41212-12-SAND 41212-32-SLATE 12 X 12 SOLARIUM ASSEMBLY INSTRUCTIONS DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS Two or more adults required for assembly Base Dimensions 12’ ½’’x12’ ½’’ Largest Dimensions 13’6’’x13’6’’ Overall Height 110” (See pg.21) APPROX. 1 ZZZ-182.41212.1126-20.GP.EN.
DO NOT DESTROY THE BOXES UNTIL COMPLETELY ASSEMBLED PLEASE VERIFY THE CONTENT OF EACH BOX AGAINST THE LIST OF PARTS 12ft x 12ft / 3.66m x 3.66m Solarium Instruction Manual IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY Consult with your local governing authority / local municipal codes regarding installation of temporary structures before purchase or assembly. Some jurisdictions may require permits for, or otherwise regulate, installation and use.
MAINTENANCE NOTES 1. In case of a defective or damaged part, or for any other questions concerning the product, please contact the manufacturer directly. 2. Please have the parts list and part numbers on hand when ordering or requesting replacement parts. 3. The product should not be installed adjacent to trees or a sloped roof. Snow and ice may slide onto the roof and cause it to collapse. 4.
Before You Assemble the Solarium Please Don't Destroy Boxes Until Completely Assembled. Tools needed: Step Ladder 6’-8’ #2 Phillips, #2 Robertson Screwdriver (not supplied) Rubber Mallet Various Files 12” piece of wood Based on the location, decide where you would like to position the two(2) door panels which can slide open to the left or to the right, your choice. Slide left to open Slide right to open 4 ZZZ-182.41212.1126-20.GP.EN.
12x12 Solarium Assembly Instructions Step 1: Before starting to assemble, please decide where you would like to position the door panels. 1. Stand up the two panels (A), using two connecting pieces (E) affix the panels (A) together. 2. Stand up a frame meant to be next to the door (B) and a door frame (D), you can chose to place the door frame on the left side or on the right side, and then use two connecting pieces (E) to affix the panel and door frame. 3.
Step 2: 1. Slide top door rail (F) into wheels of sliding door (C). 2. Slide lower door rail (G) into the plastic guide of the sliding door(C). 3. Use bolt (Bb) to affix the plastic stoppers (H) one on each end of top door rail (F). 4. Use screw (Oo) to affix upper door rail end caps (Nn) one on each end of top door rail (F). Step 3: Please note the sliding door should be installed from the inside of the solarium. 1.
Step 4: 1. Attach roof rafters (L) to the central hub (N) using bolt (Bb). (Caution: hub may be heavy, use support if needed. 2. Use screw (Z) to affix the rafters (L) onto the top of panels going through the metal piece attached to the rafter (L). Rafters must be affixed where panels connect to each other. (2) (2) Step 5: Use the same method to assemble roof rafters (K) for the angled panels.
Step 6: Use nut (Hh) and washer (Gg) to affix the top cap (M) to the central hub (N). Step 7: First remove the protective layer from the PC roof panels, then insert them (Y, Aa, Ll) into the roof rafters according to the below drawing instructions. Note: the side that had the protective layer should face down. TOP VIEW 8 ZZZ-182.41212.1126-20.GP.EN.
Step 8: After inserting the PC roof panels, insert the aluminum middle roof joints (O, P, Q) into the roof rafters. The below drawing view is from the inside of the solarium, looking up. Notes: The drain holes on the aluminum middle roof joints (O, P, Q) should be at the bottom.
Step 10: Once the PC roof is complete, use aluminum edging (S, U, W) to surround the edges of the PC roof using bolts (Bb) to fasten the rafter cap (R) and the edging, tighten securely. Step 11: Use the cross bars (T, V, X) to affix to the roof using bolts (Ff). 10 ZZZ-182.41212.1126-20.GP.EN.
Step 12: Inside each of the panels (A, B), push two plastic plugs (Ii) into the ground, and then screw down the panels using two screws (Ee) for each panel. Special notes: 1. To remove windows (08-219), pull 1 pin out of the lock position and push the frame to the end of the track, then ease the window out of the tracks one side at a time. 2. To remove screening panel, first remove windows, then unscrew the 2 screws at the top corners of the screen frame. 3. Note that this unit is not waterproof.
*Suggestions The below mentioned are only suggestions in order to permit drainage, these will vary depending on your flooring – material, flatness and slope. 12 ZZZ-182.41212.1126-20.GP.EN.
08-129-12 REGULAR FRAME A 08-131-12 2 4 3 4 2 1 08-130-12 FRAME NEXT TO DOOR B 08-132-12 SLIDING SLIDING DOOR DOOR FRAME C 3 08-133-12 E 4 8 3 1 2 1 3 1 RAIL 4 2 5 4 4 8 4 4 5 1 F Length 206 cm cm 08-137-12 08-138-12 BOTTOM 4 2 G PLASTIC STOPPER H Length 206 cm 08-139-12 08-140-12 135° ANGLED 135° ANGLED OUTSIDE INSIDE CONNECTOR 1 TOP DOOR Length 200.
08-145-12 MIDDLE ROOF JOINT 5 4 MIDDLE ROOF JOINT 5 4 RAFTER 12 5 4 5 4 5 4 5 24 5 48 CAP R 08-150-12 ROOF CROSS EDGING 5 BAR 4 Length 120.6 T Length 94.5 cm cm 08-152-12 08-151-12 ROOF CROSS EDGING 5 BAR 4 Length 120.6 V Length 94.
5 12 Cc LATCH RIGHT DOOR LATCH 5 2 SCREW 5 12 WASHER QTY IN BOX (M6x63.
AVAILABLE REPLACEMENT PARTS DESCRIPTION DRAWING DESCRIPTION 08-219-12 85-417-S PVC WINDOW ROUND SPLINE (in frame) FOR SCREENING 10-493 11-572-12 PVC WINDOW BOTTOM PLASTIC (replacement PANEL (for wall material only) panels) 85-417-P 11-822-12 ROUND SPLINE BOTTOM PLASTIC FOR PVC PANEL (for doors) WINDOW 15-123-12 15-097-12 PIN FOR PVC DOOR WHEEL WINDOW ASSEMBLY 13-033 10-458 PC WINDOW (for REPLACEMENT sliding door) WEATHERSTRIP 12-046-12 15-124-12 MOSQUITO MOUNTING SCRE
08-129-32 REGULAR 2 4 A 3 4 08-131-32 2 1 SLIDING TO DOOR B 08-132-32 1 QTY IN BOX 3 1 2 1 D 3 1 4 2 5 4 4 8 4 4 5 1 TOP DOOR 4 8 RAIL F Length 200.
08-145-32 MIDDLE ROOF JOINT 5 4 MIDDLE ROOF JOINT 5 4 RAFTER 12 5 4 5 4 5 4 5 24 5 48 CAP R 08-150-32 ROOF CROSS EDGING 5 BAR 4 Length 120.6 T Length 94.5 cm cm 08-152-32 08-151-32 ROOF CROSS EDGING 5 BAR 4 Length 120.6 V Length 94.
5 12 Cc LATCH RIGHT DOOR LATCH 5 2 SCREW 5 12 WASHER QTY IN BOX (M6x70mm) 5 39 5 20 1 4 1 4 5 4 5 12 08-193 5 1 PLASTIC PLUG Hh Ii 08-195 08-196 (47” X47 ½”) (46 ½”x43”) 1 4 BOTTOM ROOF LEFT PANEL PANEL Kk Jj 08-197 08-198 (24 ¼” X42 ¼”) (46 ½”x43”) TOP ROOF 20 Gg 08-189-32 CORNER 5 08-187 Ff BOTTOM ROOF 2 Ee 08-168-32 ACORN NUT 5 08-167-32 Dd-L BOLT DRAWING Dd-R 08-169-32 LEFT DOOR DESCRIPTION 08-165-32 08-161-32 BOLT DRAWING PACKED QTY I
AVAILABLE REPLACEMENT PARTS DESCRIPTION DRAWING DESCRIPTION 08-219-32 85-417-S PVC WINDOW ROUND SPLINE (in frame) FOR SCREENING 10-493 11-572-32 PVC WINDOW BOTTOM PLASTIC (replacement PANEL (for wall material only) panels) 85-417-P 11-822-32 ROUND SPLINE BOTTOM PLASTIC FOR PVC PANEL (for doors) WINDOW 15-123-32 15-097-32 PIN FOR PVC DOOR WHEEL WINDOW ASSEMBLY 13-033 10-458 PC WINDOW (for REPLACEMENT sliding door) WEATHERSTRIP 12-046-32 15-124-32 MOSQUITO MOUNTING SCRE
Note: The dimensions are approximate. 21 ZZZ-182.41212.1126-20.GP.EN.
