Quick Reference Guide
Table Of Contents
- Contents
- About This Reference
- Checking Out Your Computer
- Setting Up and Getting Started
- Working safely and comfortably
- Preparing power connections
- Connecting to a broadband modem or network
- Connecting a dial-up modem
- Starting your computer
- Turning off your computer
- Restarting (rebooting) your computer
- Using the keyboard
- Using the mouse
- Using optical drives
- Using the memory card reader
- Using the diskette drive
- Adjusting the volume
- Installing a printer, scanner, or other device
- Upgrading Your Computer
- Preventing static electricity discharge
- Opening and closing the case
- Removing and installing the front bezel
- Installing memory
- Replacing an optical or diskette drive or a card reader
- Replacing the hard drive
- Adding or replacing an expansion card
- Replacing the front fan
- Replacing the rear fan
- Replacing the front I/O board
- Replacing the processor
- Replacing the system battery
- Replacing the power supply
- Replacing the system board
- Maintaining Your Computer
- Troubleshooting
- Safety guidelines
- First steps
- Troubleshooting
- Add-in cards
- Audio
- CD or DVD drives
- Diskette drive
- The diskette drive is not recognized
- You cannot save a file to diskette or you see the message “disk is full or write-protected”
- You see an “Access Denied” or “Write protect” error message
- You see a “Disk is full” error message
- You see a “Non-system disk” or “Disk error” error message
- The diskette drive LED is lit continuously
- Display
- DVD drives
- Ethernet
- Expansion cards
- File management
- Floppy drive
- Hard drive
- Internet
- Keyboard
- Memory
- Memory card reader
- Modem (cable or DSL)
- Modem (dial-up)
- Your modem does not dial or does not connect
- You cannot connect to the Internet
- Your 56K modem does not connect at 56K
- Your fax communications program only sends and receives faxes at 14,400 bps when you have a 56K modem
- The modem is not recognized by your computer
- The modem is noisy when it dials and connects
- Monitor
- Mouse
- Networks
- Passwords
- Power
- Printer
- Sound
- Recovering your system
- Telephone support
- Legal Notices
- Index
www.gateway.com
85
Ethernet
You cannot see the other computers on your network
• Make sure that your Ethernet cable is plugged into the
Ethernet jack on your computer, as shown in your setup
poster. Make sure that the other end is plugged into a
network router, switch, hub, or other network device.
• Make sure that all computers are plugged into a
powered electrical outlet and turned on.
• Make sure that the router (if you are using one) is
plugged into a powered electrical outlet and turned on.
Most routers have lights that indicate they are working.
For more information, see the documentation that came
with your router.
• If you are using a router, try rebooting it by unplugging
its power cord, waiting five seconds, then plugging it
back in.
• Make sure that all computers on your network have the
same workgroup name.
• Make sure that all computers are using the same Subnet
Mask.
• If you assigned IP addresses to the computers, make sure
that all computers have different IP addresses. For home
networks, IP addresses should be 192.168.N.N where N
is a number you assign between 0 and 254. The first N
should be the same for all computers on your network
and the second N should be different for all computers
on your network.
The computer does not recognize an Ethernet expansion
card
• Shut down and restart your computer.
• Make sure that you have installed the required software.
For more information, see the documentation that came
with your Ethernet card.
• Reseat the card. For more information about reseating
the card, see “Adding or replacing an expansion card” on
page 47. For more information about your Ethernet card,
see the documentation that came with your Ethernet
card.
8512735.book Page 85 Thursday, September 27, 2007 1:03 PM