Quick Reference Guide
Table Of Contents
- Contents
- About This Reference
- Checking Out Your Computer
- Setting Up and Getting Started
- Working safely and comfortably
- Preparing power connections
- Connecting to a broadband modem or network
- Connecting a dial-up modem
- Starting your computer
- Turning off your computer
- Restarting (rebooting) your computer
- Using the keyboard
- Using the mouse
- Using optical drives
- Using the memory card reader
- Using the diskette drive
- Adjusting the volume
- Installing a printer, scanner, or other device
- Upgrading Your Computer
- Preventing static electricity discharge
- Opening and closing the case
- Replacing the optical disc drive
- Replacing the diskette drive
- Replacing the memory card reader
- Replacing the hard drive
- Installing memory
- Adding or replacing an expansion card
- Replacing the heat sink and processor
- Replacing the system battery
- Replacing the power supply
- Replacing the system board
- Maintaining Your Computer
- Troubleshooting
- Safety guidelines
- First steps
- Troubleshooting
- Add-in cards
- Audio
- CD or DVD drives
- Diskette drive
- The diskette drive is not recognized
- You cannot save a file to diskette or you see the message “disk is full or write-protected”
- You see an “Access Denied” or “Write protect” error message
- You see a “Disk is full” error message
- You see a “Non-system disk” or “Disk error” error message
- The diskette drive LED is lit continuously
- Display
- DVD drives
- Ethernet
- Expansion cards
- File management
- Floppy drive
- Hard drive
- Internet
- Keyboard
- Media Center
- Memory
- Memory card reader
- Modem (cable or DSL)
- Modem (dial-up)
- Your modem does not dial or does not connect
- You cannot connect to the Internet
- Your 56K modem does not connect at 56K
- Your fax communications program only sends and receives faxes at 14,400 bps when you have a 56K modem
- The modem is not recognized by your computer
- The modem is noisy when it dials and connects
- Monitor
- Mouse
- Networks
- Passwords
- Power
- Printer
- Sound
- Recovering your Windows Vista system
- Recovering pre-installed software and drivers
- Using Microsoft System Restore
- Recovering your system to its factory condition
- Recovering your system using the Windows DVD
- Recovering your Windows XP system
- Telephone support
- Legal Notices
- Index
www.gateway.com
137
Canada
Industry Canada (IC) Unintentional emitter per
ICES-003
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital
apparatus as set out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites
applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage
radioélectrique édicté par Industrie Canada.
Telecommunications per Industry Canada CS-03 (for
products fitted with an IC-compliant modem)
The Industry Canada label identifies certified equipment. This certification means that the
equipment meets certain telecommunications network protective, operation, and safety
requirements. The Department does not guarantee the equipment will operate to the users’
satisfaction.
Before installing this equipment, users should make sure that it is permissible to be connected
to the facilities of the local telecommunications company. The equipment must also be installed
using an acceptable method of connection. In some cases, the inside wiring associated with a
single-line individual service may be extended by means of a certified connector assembly. The
customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user
to disconnect the equipment.
Users should make sure, for their own protection, that the electrical ground connections of the
power utility, telephone lines, and internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural areas.
The
Ringer Equivalence Number
(REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices subject
only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does
not exceed 5.
Laser safety statement
All Gateway systems equipped with CD and DVD drives comply with the appropriate safety
standards, including IEC 825. The laser devices in these components are classified as “Class 1
Laser Products” under a US Department of Health and Human Services (DHHS) Radiation
Performance Standard. Should the unit ever need servicing, contact an authorized service
location.
Warning
To avoid electrical shock or equipment malfunction do not attempt to
make electrical ground connections by yourself. Contact the appropriate
inspection authority or an electrician, as appropriate.
Warning
Use of controls or adjustments or performance of procedures other than
those specified in this manual may result in hazardous radiation exposure. To
prevent exposure to laser beams, do not try to open the enclosure of a CD or
DVD drive.
8512138.book Page 137 Friday, March 16, 2007 4:33 PM