Quick Reference Guide
Table Of Contents
- Contents
- About This Reference
- Checking Out Your Computer
- Setting Up and Getting Started
- Working safely and comfortably
- Preparing power connections
- Connecting to a broadband modem or network
- Connecting a dial-up modem
- Starting your computer
- Turning off your computer
- Restarting (rebooting) your computer
- Using the keyboard
- Using the mouse
- Using optical drives
- Using the memory card reader
- Using the diskette drive
- Adjusting the volume
- Installing a printer, scanner, or other device
- Upgrading Your Computer
- Preventing static electricity discharge
- Opening and closing the case
- Replacing the optical disc drive
- Replacing the diskette drive
- Replacing the memory card reader
- Replacing the hard drive
- Installing memory
- Adding or replacing an expansion card
- Replacing the heat sink and processor
- Replacing the system battery
- Replacing the power supply
- Replacing the system board
- Maintaining Your Computer
- Troubleshooting
- Safety guidelines
- First steps
- Troubleshooting
- Add-in cards
- Audio
- CD or DVD drives
- Diskette drive
- The diskette drive is not recognized
- You cannot save a file to diskette or you see the message “disk is full or write-protected”
- You see an “Access Denied” or “Write protect” error message
- You see a “Disk is full” error message
- You see a “Non-system disk” or “Disk error” error message
- The diskette drive LED is lit continuously
- Display
- DVD drives
- Ethernet
- Expansion cards
- File management
- Floppy drive
- Hard drive
- Internet
- Keyboard
- Media Center
- Memory
- Memory card reader
- Modem (cable or DSL)
- Modem (dial-up)
- Your modem does not dial or does not connect
- You cannot connect to the Internet
- Your 56K modem does not connect at 56K
- Your fax communications program only sends and receives faxes at 14,400 bps when you have a 56K modem
- The modem is not recognized by your computer
- The modem is noisy when it dials and connects
- Monitor
- Mouse
- Networks
- Passwords
- Power
- Printer
- Sound
- Recovering your Windows Vista system
- Recovering pre-installed software and drivers
- Using Microsoft System Restore
- Recovering your system to its factory condition
- Recovering your system using the Windows DVD
- Recovering your Windows XP system
- Telephone support
- Legal Notices
- Index
CHAPTER 6: Troubleshooting
102
Modem (dial-up)
See also “Internet” on page 98.
Your modem does not dial or does not connect
• Make sure that the modem cable is plugged into the
modem jack and not the Ethernet network jack. See
your setup poster to make sure that the connections
have been made correctly.
• Make sure that your computer is connected to the
telephone line and the telephone line has a dial tone.
• Make sure that the modem cable is less than 6 feet
(1.8 meters) long.
• Remove any line splitters or surge protectors from your
telephone line, then check for a dial tone by plugging
a working telephone into the telephone wall jack.
• If you have additional telephone services such as call
waiting, call messaging, or voice mail, make sure that
all messages are cleared and call waiting is disabled
before using the modem. Contact your telephone
service to get the correct code to temporarily disable
the service. Also make sure that the modem dialing
properties are set correctly.
To check the dialing properties in Windows Vista:
1 Click (Start), then click Control Panel. The
Control Panel window opens.
2 Click Hardware and Sound, then click Phone and
Modem Options. The Phone and Modem Options
dialog box opens.
3 If this is the first time you have accessed this
category, the Location Information dialog box
opens. Enter the information for your area, then
click OK.
4 Click the Dialing Rules tab, click the location from
which you are dialing, then click Edit.
5 Make sure that all settings are correct.
Help
For more information about dialing properties, click Start, then
click Help and Support. Type the keyword dialing in the Search Help
box, then press E
NTER.
8512138.book Page 102 Friday, March 16, 2007 4:33 PM