Quick Setup Guide
USING YOUR LIGHTSTRIP
[REVIEWERS: If you turn off or unplug your lightstrip, will it remember your
last brightness and color settings?]
Aim your remote at the control box to adjust your
lightstrip’s settings:
• Press a color button to change the color. There are 16
selectable colors, including white.
• Press (brightness up) or (brightness down) to adjust
the brightness when using a single color. There are eight
brightness levels.
• Press (speed up) or (slow down) to adjust how
quickly the lights cycle through colors. There are eight
speed levels for the Sunrise/Sunset, Jump 3/Jump 7, Fade
3/Fade 7, and Flash/Auto modes.
• Press a mode button to change a color mode. There are
eight modes:
• Sleep timer: Press to schedule the lightstrip to turn
• Reactive music: Lights change based on the preset
tempo beat of music. There are four modes (classical,
gentle, dynamic, and disco).
• Sunrise/Sunset: Lights cycle from dark to bright
(sunrise) or bright to dark (sunset).
• Jump 3
• Jump 7
• Fade 3
• Fade 7
• Flash 7
• Auto
Jump 7, Fade 3, Fade 7, and Flash 7). Each mode is
repeated three times, then automatically moves to the
next mode.
Adhesive backing
Note: You can secure your lightstrip in place with its adhesive
backing or cable clips.
CAUTION: To avoid damage to the lightstrip, do not sharply twist or
bend the lightstrip 90° or more.
1
lights where you want them.
2 Optional: Attach the double-sided tape to the back of the
light control, then attach it where you want it.
Notes:
• Make sure that the lightstrip is unrolled, otherwise it can
if the LED tape detaches from the surface. Small pieces of clear
tape can be used.
Cable clips
1 Make sure that your mounting location is clean, dry, and
free of oils.
2 Remove the adhesive backing on a cable clip, and push it
3 Align the lightstrip with the cable clip.
4 Slide the cable clip through the buckle and pull to tighten.
5 Repeat steps 1-4 to attach the second cable clip.
SPECIFICATIONS
• Input: 12V DC, 2A
AC100-240V, 50/60Hz
• LED tape length: 16.4 ft. (5 m)
• LED quantity: 150
• LED life: 30,000 hours (approximate)
• Remote control battery: CR2025
• Remote control range: 30 ft. (9.1 m)
• Wattage: 16.8W
• AC adapter cable length: 6 ft. (1.8 m)
TROUBLESHOOTING
LEDs will not turn on.
• Press the power button to make sure that your light is
turned on, then select the color or mode you want.
• Make sure that all of the connectors are connected properly
and the AC adapter is plugged into a power outlet.
• Make sure that you have removed the plastic battery-saver
tab from the remote before use. If you already removed the
battery-saver tab, make sure that the battery still works. If
the battery does not work, replace the battery and try
again.
• Make sure that the power cable is not damaged.
V1 ENGLISH 22-0366
SAFETY INFORMATION
• To avoid damage to the lightstrip, do not sharply twist or
bend the lightstrip 90° or more.
• Do not cut the silver solder markings. Only cut in the
center of the copper-colored pads.
• Do not plug in your lights when they are coiled. This can
generate excess heat, which can result in product
LEGAL NOTICES
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful i
nterference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
party responsible for compliance could void the user’s authority to operate the
equipment.
WARNING: Chemical Burn Hazard. Keep batteries away from children.
This product contains a lithium button/coin cell battery. If a new or
used lithium button/coin cell battery is swallowed or enters the body,
it can cause severe internal burns and can lead to death in as little as
two hours. Always completely secure the battery compartment. If the battery
compartment does not close securely, stop using the product, remove the battery,
and keep it away from children. If you think batteries might have been swallowed o
r
placed inside any part of the body, seek immediate medical attention.
The cells must be disposed of properly, including keeping them away from children.
Even used cells may cause injury.
ICES statement
CAN ICES-5(B)/NMB-5(B)
Visit www.insigniaproducts.com for details
CONTACT INSIGNIA:
For customer service, call 1-877-467-4289 (U.S.
and Canada)
www.insigniaproducts.com
Distributed by Best Buy Purchasing, LLC
©2022 Best Buy. All rights reserved.
Cable clip
Adhesive back
Wire
GW: it will remember last setting.