Brochure

Gastite Division, Titeflex Corporation
1116 Vaughn Parkway / Portland, TN 37148
800.662.0208 / www.gastite.com / [e-mail]
80
April 2015
Section 7: Sizing Tables and Pressure Drop Charts
Table 7-11
Maximum Capacity of FlashShield™ Flexible Gas Piping in Cubic Feet Per Hour of Natural Gas
with a Gas Pressure of 5.0 PSI and a Pressure Drop of 3.5 PSI
(based on a 0.60 specific gravity gas)
Tubing Tubing Length (ft)
EHD Size 5 10 15 20 25 30 40 50 60 70 80 90 100 125 150
13 3/8" 760 527 425 365 324 295 253 225 204 188 175 165 156 138 126
18 1/2" 1775 1261 1032 896 802 733 636 570 521 483 452 426 405 363 331
23 3/4" 2838 2064 1713 1501 1355 1246 1092 986 906 844 794 752 717 647 595
31 1" 7311 5239 4312 3755 3373 3090 2691 2417 2214 2056 1929 1822 1732 1556 1426
37 1-1/4" 11587 8248 6761 5872 5263 4813 4180 3747 3426 3177 2976 2809 2667 2391 2186
48 1-1/2" 24713 17563 14382 12482 11182 10221 8871 7947 7264 6733 6304 5949 5648 5060 4625
60 2" 58818 41150 33391 28790 25662 23361 20142 17954 16344 15096 14092 13262 12561 11196 10192
Tubing Tubing Length (ft)
EHD Size 200 250 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
13 3/8" 108 96 87 75 66 60 56 52 49 46 44 42 40 39 37
18 1/2" 287 257 235 204 183 167 155 145 137 130 124 119 114 110 106
23 3/4" 521 471 433 379 342 315 293 276 261 249 238 229 221 213 207
31 1" 1242 1115 1022 890 799 732 680 638 603 573 547 525 505 487 471
37 1-1/4" 1899 1702 1556 1352 1212 1108 1027 962 908 863 823 789 758 731 707
48 1-1/2" 4014 3596 3287 2853 2556 2336 2165 2027 1913 1816 1733 1660 1596 1539 1487
60 2" 8788 7833 7131 6148 5480 4989 4608 4301 4048 3834 3650 3490 3349 3224 3111
Caution: Capacities shown in the elevated pressure tables may exceed the capacity of the line regulator. Refer to Section 4 for Regulator
Capacities and Pressure Drops.
Table 7-12
Maximum Capacity of FlashShield™ Flexible Gas Piping in Cubic Feet Per Hour of Natural Gas
with a Gas Pressure of 10.0 PSI and a Pressure Drop of 7.0 PSI
(based on a 0.60 specific gravity gas)
Tubing Tubing Length (ft)
EHD Size 5 10 15 20 25 30 40 50 60 70 80 90 100 125 150
13 3/8" 1097 760 613 527 468 425 365 324 295 271 253 238 225 200 181
18 1/2" 2499 1775 1453 1261 1129 1032 896 802 733 679 636 600 570 510 466
23 3/4" 3902 2838 2356 2064 1863 1713 1501 1355 1246 1161 1092 1034 986 890 818
31 1" 10201 7311 6016 5239 4707 4312 3755 3373 3090 2869 2691 2543 2417 2171 1989
37 1-1/4" 16276 11587 9498 8248 7394 6761 5872 5263 4813 4463 4180 3945 3747 3359 3071
48 1-1/2" 34773 24713 20237 17563 15734 14382 12482 11182 10221 9474 8871 8370 7947 7120 6508
60 2" 84071 58818 47727 41150 36680 33391 28790 25662 23361 21577 20142 18956 17954 16003 14568
Tubing Tubing Length (ft)
EHD Size 200 250 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500
13 3/8" 156 138 126 108 96 87 80 75 70 66 63 60 58 56 54
18 1/2" 405 363 331 287 257 235 218 204 193 183 174 167 161 155 150
23 3/4" 717 647 595 521 471 433 403 379 359 342 328 315 303 293 284
31 1" 1732 1556 1426 1242 1115 1022 949 890 841 799 763 732 705 680 658
37 1-1/4" 2667 2391 2186 1899 1702 1556 1443 1352 1276 1212 1156 1108 1065 1027 993
48 1-1/2" 5648 5060 4625 4014 3596 3287 3047 2853 2692 2556 2438 2336 2246 2165 2093
60 2" 12561 11196 10192 8788 7833 7131 6586 6148 5786 5480 5218 4989 4787 4608 4447
Caution: Capacities shown in the elevated pressure tables may exceed the capacity of the line regulator. Refer to Section 4 for Regulator
Capacities and Pressure Drops.
Tables include losses for four 90° bends and two end fittings. Tubing runs with a larger number of bends and/or fittings shall be increased
by an equivalent length of tubing to the following equation: L=1.3n where L is additional length of tubing and n is the number of
additional fittings and/or bends.