Product Manual

GENERAL INFORMATION
GAS CONSUMPTION g/h MJ/h BTU FM Jet
Small Lantern 2011 58 g/h 3MJ/h 2850BTU 0.10mm
Medium Lanterns 2012 & 2012PL 58 g/h 3MJ/h 2850BTU 0.10mm
SAFE APPLIANCE LOCATIONS
Thisapplianceshallonlybeusedinanabove
groundopen-airsituationwithnaturalventilation,
withoutstagnantareas,wheregasleakageand
products of combustion are rapidly dispersed by
windandnaturalconvection.
Any enclosure in which the appliance is used
shall comply with the following:
An enclosure with walls on all sides, but at least
onepermanentopeningatgroundlevelandno
overheadcover(seeExample1).
Within a partial enclosure that includes an
overheadcoverandnomorethantwowalls
(seeExample2&3).
Within a partial enclosure that includes an
overhead cover and more than two walls, the
following will apply:
atleast25%ofthetotalwallareaiscompletely
open,andatleast30%oftheremainingwallarea
isopenandunrestricted(seeExample4&5).
In the case of balconies, at least 20% of the
total wall area shall be and remain open and
unrestricted.
DIAGRAMMATIC REPRESENTATIONS OF OUTDOOR AREAS
Thefollowingguresarediagrammaticrepresentationsofoutdoorareas.Rectangularareashavebeen
usedinthesegures–thesameprinciplesapplytoanyothershapedarea.
INSTRUCTIONS FOR USE
1. Removelanternfromcartonandremoveany
transit protection material.
2. Thelanternmustbeplacedonastable
horizontal surface.
 a. Theapplianceareamustbekeptclearand
free of combustible materials, gasoline and
  otherflammablevapoursandliquids.
 b. Gasorificesandburnermustbekept
clear of dirt and cobwebs. Flow of
  combustionandventilationairthroughthe
perforated portions of the appliance must
not be obstructed.
c. Any cleaning agent used on the appliance
should be of a non-combustible and
  non-corrosivenature.
3. Properclearancefromcombustiblematerials
must be maintained at all times. The minimum
 clearancesareasfollows:
Minimum Clearance from Combustibles:
Side600mm Top600mm
Combustible materials are considered to be
wood, compressed paper, plant fibres, plastic,
plexiglasorothermaterialscapableofbeing
ignited and burned.
Such materials shall be considered combustible
eventhoughflameproofed,fire-retardant
treated or plastered. Additional clearance may
be required for glass, painted surfaces and other
materials which may be damaged by radiant or
convectionheat.
4. Attach the lantern to the specified camping
 cylinderandensurethatcontrolvalveisfully
closed.
TO ATTACH MANTLE
Tieorclipmantlesaroundgrooveinburnertube.
Distributefoldsonthemantleevenly.Cutoff
surplus string. Be careful that mantle does not
snag on electrodes and tear.
LIGHTING AND BURNING OFF MANTLE
Light the mantle with a lighted match with gas
turned on slightly. Allow the mantle to burn until
itstopsshrinkingthenopenthevalvefurther
untilthemantletakesitscorrectshape.Close
controlvalveandallowmantletocool,thenitis
readyforuse.NOTE:Themantleisnowvery
brittle and should not be touched.
RELIGHTING AND REGULATING
Once the mantle has been burned off, the lantern
can be relit by inserting a lighted match through
the lighting hole or pressing the piezo ignition
button (if equipped) while simultaneously opening
thecylindervalve.Whenmantleislit,turnknob
anti-clockwisetoincreaselightintensity,and
clockwisetodecreaseintensityorextinguish.
Donotopenvalvebeyondthepointwhere
maximumintensityisreachedasthismaycause
unnecessary flaring, and waste of gas.
REPLACING JETS
Ifthejetshouldbecomeblockedorneed
replacement,removethelanternconnector
assemblytowhichthejetisassembled.The
jetcannowberemoved.Toclearblockedjets
washinpetrol.Donotusewiresorprickers.
If
washingisunsuccessful,fitnewjet.When
refittingthejet,makesureitistight.
REPLACING MANTLE
Carefullyremovealltracesofoldmantle.Fitthe
new mantle by tying or clipping firmly into the
grooveoftheburnertubeandspreadevenlyall
around. The mantle can then be burned off as
describedpreviously.
ANNUAL MAINTENANCE
Clean the body of your appliance using a cotton
clothsoakedinsoapyhotwater.Neveruse
abrasiveorflammablecleaningproducts.Usea
soft brush to clean the burner.
STORAGE
When the appliance is not used it must be
stored in a suitable area to protect it from any
riskofdeterioration.Keepitinawellventilated
area and out of reach of children.
HANDY HINTS
a.Inspectthe“O”Ringandrubberwasher
regularly and replace if worn or damaged.
b. Neverconnectordisconnectthelantern
near an open flame.
c. CheckforgasleakswithSOAPYWATER.
DO NOT USE A FLAME.
d.
Ensure that the area in which the lantern is
tobeusediswellventilatedandDONOTuse
lanternasaspaceheaterintent,caravan,
etc.
e. Ensurethelanterniscompletelyextinguished
before disconnecting from the gas cylinder.
f. DONOTplacethelanterncloserthan60cm
from ceiling or flammable material.
g. Avoidmovingthelanternduringuseasthis
can cause large flames.
THINGS YOU SHOULD KNOW
1. Alwayshaveasparesetofmantles.Once
burned, a mantle is fragile and can be
damaged if touched or dropped.
2.Ifyourlanternburnswithayellowsmokey
flame,checktheburnerandairtubefor
spider webs.
3.Thislanternconsumesair(oxygen).DONOT
USEinunventilatedareas.Ampleventilation
mustbeprovided.
4. Provideadditionalventilationforanyother
fuel burning appliances which may be
operating within the same enclosed area.
5. Neverallowtents,sleepingbags,oranyother
flammable material to come within 5 metres
of this appliance.
SPARE PARTS - MANUAL MODELS
Model No. 2011 and 2012
01 Cover
02 Burnertube
03 Frame
04 Handle
05 ‘E’Jet(0.10mm)
06 Airmixingcollar
07 Shieldcup
08 Locknut
GM200 Mantlefor2011or2012
G01FG Heatresistantglassfor2011
G02FG Heatresistantglassfor2012
AD9-01 3/8”BSP.LHconnector
AD9-02 O-ringforconnector
SPARE PARTS - PIEZO MODELS
Model No. 2012PL
01 Cover
02 Burnertube
03 Frame
04 Handle
05 Airmixingcollar
06 ‘E’Jet(0.10mm)
07 Piezoignitorwithbutton
08 Electrode
09 Base
10 Locknut
11 Locknutforburnertube
GM200 Mantlefor2012PL
G02FG Heatresistantglassfor2012PL
AD9-01 3/8”BSP.LHconnector
AD9-02 O-ringforconnector
01
GO1FG
GO2FG
03
04
07
06
05
AD9-01
AD9-02
08
02
GM200
04
02
11
GM200
GO2FG
01
03
08
05
07
10
09
06
AD9-01
AD9-02