Corporate Headquarters Magnum CSG14 Gigabit Converter Switches GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539-7437 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Email: support@garrettcom.com Installation and User Guide www . GarrettCom . com www . GarrettCom .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Magnum™ CSG14 Series Gigabit Converter Switch Installation and User Guide Part #: 84-00102Z Rev. A Trademarks GarrettCom, Magnum, Link-Loss-Learn, S-Ring, Convenient Switch, Converter Switch are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc. Ethernet is a trademark of Xerox Corporation NEBS is a trademark of Telcordia Technologies UL is a registered trademark of Underwriters Laboratories www .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Important: The Magnum CSG14 Series 10/100/1000 Mb/s Converter Switches contain no user serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. If problems are experienced with Magnum CSG14 10/100/1000 Mb/s Converter Switch products, consult Section 5, Troubleshooting, of this User Guide. Copyright © 2008 GarrettCom, Inc. All rights reserved.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Federal Communications Commission Radio Frequency Interference Statement This equipment generates, uses and can radiate frequency energy and if not installed and used properly, that is in strict accordance with the manufacturer's instructions, may cause interference to radio communication.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Contacting GarrettCom, Inc Please use the mailing address, phone and fax numbers and email address listed below: GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539 Phone (510) 438-9071 Fax (510) 438-9072 Website: http://www.GarrettCom.com Email: support@garrettcom.com www . GarrettCom .
CSG14 Series Gigabit Converter Switch TABLE OF CONTENTS Installation and User Guide (05/08) Page 1.0 SPECIFICATIONS ............................................................................... 1 1.1 Technical Specifications ...................................................................... 1 1.2 Summary of models and descriptions: ............................................... 11 2.0 INTRODUCTION ............................................................................... 14 2.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 3.6 Powering the CSG14H and CSG14P (DC internal) .......................... 45 3.7 CSG14H and P Series , DC-powered, Installation............................. 47 3.8 Connecting Ethernet Media ............................................................... 48 3.8.1 Connecting Twisted Pair ............................................................ 50 3.8.2 Connecting Fiber Optic LC-type, “Small Form factor (SFF)” ... 51 3.8.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 5.4 Shipping and Packaging Information................................................. 67 APPENDIX A: WARRANTY INFORMATION ......................................... 69 Revisions Rev A 05/08: Initial release of this user manual for CSG14 Converter Switches GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice. www . GarrettCom .
CSG14 Series Gigabit Converter Switch 1.0 1.1 Installation and User Guide (05/08) SPECIFICATIONS Technical Specifications Ports Performance Data Rate: 10Mbps, 100Mbps, 1000Mbps Network Standards 1000Mb: Ethernet IEEE 802.3ab and 802.3z 1000Base-T, -SX, -LX and -ZX 100Mb: Ethernet IEEE 802.3u, 100BASE-TX, 100BASE-FX 10 Mb: Ethernet IEEE 802.3, 10BASE-T Auto-sensing for speed: IEEE 802.3z Packet-Processing Between Domains Filter and Forward Rate from 1000Mbps ports: 1,488,000 pps max.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Packet buffers memory: 64KB, dynamically shared on all domains Latency (not including packet time): 100 to 10 Mbps: 5μs 10 to 100Mbps: 15μs Path Delay Value: 50 BT on all ports Maximum Ethernet Segment (or Domain) Lengths 10BASE-T (Unshielded twisted pair) 10BASE-FL, Fiber optic 10BASE-FL, Single-mode Fiber optic 100BASE-TX (CAT 5 UTP) 100BASE-FX, half-duplex: (multi-mode) 100BASE-FX, full duplex: (multi-mode) 100BASE-FX, half-duple
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 1000BASE-ZX, full duplex, single-mode (9um) >70 km (229,659 ft) Operating Environment CSG14H: -13ºF to 140ºF (-25ºC to 60ºC) Long term per agency tests (UL).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Note: CSG14 models are designed for NEBS compliance, including, vibration, shock and altitude. Packaging: Enclosure: Rugged sheet metal (Steel). Dimensions of the Switch unit: 3.5 in H x 3.0 in W x 1.0 in D (8.9 cm x 7.6 cm x 2.5 cm) Weight: all models: 4.6 oz. (130g); Power supply, –Hd, and Hi: 5.8 oz (165g) –Pd, and -Pi: 7.9 oz (225g) Cooling Method: Convection on the CSG14 Series models.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) POWER SUPPLY These products are intended to be supplied by a Listed, Direct Plug-In power unit, marked “Class 2”, or a Listed ITE Power Supply, marked “LPS”, which has suitably rated output voltage (i.e. 9vdc, 12vdc, 24vdc, 48vdc), and suitably rated output current (i.e. 100mA to 500mA). When connected to a 48 V centralized dc source these products shall be provided with a Listed 5A DC fuses in the supply circuit.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) International (-Hi) models. Factory floor temperature rated. Input: IEC 320 connector on the 100-240vac 47-63Hz external power adapter. Requires a user supplied power cord Output: 12vdc, 1.25Amps. Temperature un-controlled Premium (P) Ratings (-40 to 75°C) North America (-Pd) models. Outdoor temperature rated. Input: 6ft AC power cord to IEC 320 connector on the100-240vac 47-63Hz external power adapters. Output: 12vdc, 2Amps.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 24V DC internal (range of 18 to 36V DC). -48V DC internal (range of 36 to 60V DC), -, ground. Power Consumption: See Section 3.6. Note 1: the 8-15V DC jack can be used for dual source DC input using an AC adapter and the DC terminal block. Power supply protection is provided by internal diodes. Note 2: The Direct DC power floats. The user may ground either “+” or “-” if desired. www . GarrettCom .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Port Connectors: Two RJ-45 Ports: support 10/100/1000Mbps with auto cross (MDIX). They are shielded 8-pin female connectors for shielded (STP) and unshielded (UTP) Cat 3, 4, 5 cables. One Fiber optic port: The CSG14 series is 1000Base-SX / -LX / -ZX with a “fiber flavor” choice of multimode SC or SLC connectors Switches Fiber port default is FDX (Full-Duplex) RJ45’s are triple-speed auto-negotiating www . GarrettCom .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) LED Indicators (Two sets) top-front and end with ports Top-Front: POWER: Steady ON when power applied Gb per RJ45 port: Steady ON for 1000Mbps; OFF for 100Mbps or 10Mb speed LK/ACT per port: Steady ON for LINK (LK) with no traffic, BLINKING for Activity End with Ports: POWER: Steady ON when power applied 10/100/1000Mb per port: Steady ON for 100Mb, OFF for 10Mb, BLINKING for 1000Mb Fiber port: LK/ACT: Steady ON for Link with no traf
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Agency Approvals and Standards Compliance: UL Listed (UL 60950), cUL, CE, Emissions meets FCC Part 15 Class A. NEBS L3 and ETSI compliant. P model: IEEE P1613 Env. Std for Electric Power Substations P model: NEMA TS-2 and TEES for traffic control equipment P model: designed for UL 2043 above-the-ceiling installation IEC61850 EMC and Operating Conditions Class C Power Substations Warranty: Three years, return to factory www .
CSG14 Series Gigabit Converter Switch 1.2 Installation and User Guide (05/08) Summary of models and descriptions: CSG14H (Hardened Model) for 1000Mb fiber CSG14H-ff-Hd, Hi = CSG14H-ff-12VDC = CSG14H-ff-24VDC = CSG14HR-ff-24VDC = CSG14H-ff-48VDC = Hardened (H), two 10/100/1000Mb RJ-45+ one 1000Mb Fiber port for factory floor (-25 to 60C) using a direct DC ( 8-15VDC) and/or external AC hardened power supply (included).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) CSG14P (Premium Model) for 1000Mb fiber CSG14P-ff-Pd, Pi = CSG14P-ff-12VDC = CSG14P-ff-24VDC = CSG14PR-ff-24VDC = CSG14P-ff-48VDC = Premium (P), two 10/100/1000Mb RJ-45+ one 1000Mb Fiber port for uncontrolled(outdoor) (-40 to 75C) using direct DC (8-15VDC) and/or external AC premium power supply (included). Same as CSG14P-Pd, Pi, except AC Premium Power Supply is not included.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) “LX25” = 1000Base-LX-SLC: 1310nm multi-mode fiber optic with LC type connector, 25 km “ZX40” = 1000Base-ZX-SLC: 1550nm single-mode fiber optic with LC type connector, 40 km “ZX70”= 1000Base-ZX-SLC: 1550nm single-mode fiber optic with LC type connector, 70 km “SFP” = open SFP transceiver slot in the fiber position.
CSG14 Series Gigabit Converter Switch 2.0 Installation and User Guide (05/08) INTRODUCTION This section describes CSG14 Series models, including appearance, features and typical applications. 2.1 Inspecting the Package and the Product Examine the shipping container for obvious damage prior to installing this product; notify the carrier immediately of any damage, which you believe occurred during shipment or delivery.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 1 set Metal panel mounting clips and screws (2 each) 1 User Guide (this manual) Remove the Magnum CSG14 Series Converter Switch from the shipping container. Be sure to keep the shipping container should you need to ship the unit at a later date. In the event there are items missing or damaged contact your supplier. If you need to return the unit, use the original shipping container.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) fiber connector types plus AC or DC input power selection and multiple application environments, and you have the Magnum CSG14 Converter Switch family. The Magnum CSG14 family of Converter Switches with a 1000Mb, 100Mb or 10Mb Fiber port built in covers the full range of application environments, with Hardened (factory floor), and Premium-rated (outdoor) versions.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The Magnum CSG14H Hardened units are for the office and factory floor applications. The CSG14H models are built with high-grade components and are constructed using special thermal techniques and a metal case for heavy-duty industrial jobs. In addition to a Hardened AC power option and jack, terminals for internal DC power choices at 8 to15V, 24V or -48V DC are included.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) the CSG14H Hardened units. In addition to a Premium-rated AC power option and jack, terminals for internal DC power choices at 8 to15V, 24V or -48V DC are included. When used outdoors, the CSG14P should be protected from falling rain. Mounting options include stand-alone panel mounting, DIN-rail, or rack-mount tray.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Fig 2.2a CSG14H with 1000Mb SC connector Fig 2.2b The ORANGE labeled Magnum CSG14H hardened units (as shown in Fig 2.2a) are designed for office and wiring closet environments and factory floor/Industrial applications. Using special thermal techniques and a sealed rugged metal case for heavy-duty industrial applications no air inflow is required for cooling, so the CSG14H resist dust, dirt, moisture, smoke and insects.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Fig 2.2.b CSG14P with 1000Mb LC connector The RED labeled Magnum CSG14P Series (as shown in Fig. 2.2b) are premium rated units suitable for temperature un-controlled outdoor applications. Specially designed with premium-grade extended temperature components, the CSG14P units use similar thermal techniques to the CSG14H hardened units for cooling. Mounting options include panel mounting, DIN-rail, or rack-mount tray.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The front side of the unit has two twisted-pair 10/100/1000Mb switch ports and one 10, 100 or 1000Mb fiber port. Both the RJ-45 ports of the CSG14 Series Converter switches support auto cross (MDIX) operation performing the autocross function under auto-negotiation mode only. The CSG14 models are factory configured at Full Duplex.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The single fiber port on the CSG14 is multi-mode with an SC connector or small form-factor connector (LC single-mode). The external DC power plug connector and/or “jack” and the internal DC input terminal is provided on the rear of the unit. 2.3 Frame Buffering and Latency The Magnum CSG14 Series Converter Switches are store-and-forward switches.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) minimal frame latency, they will also permit bad frames to propagate out to the Ethernet segments connected. The "cut-through" technique permits collision fragment frames, which are a result of late collisions, to be forwarded to add to the network traffic.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) all ports, resulting in a small, fixed number of packets to be stored per port. When the port buffer fills up, dropped packets result.) This dynamic buffer allocation provides the capability for the maximum resources of the Magnum CSG14 Series unit to be applied to all traffic loads, even when the traffic activity is unbalanced across the ports.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) a second and is transparent to an observer. See Section 4.6 for additional details. Another feature implemented in Magnum CSG14 Series Converter Switches is a collision-based flow-control mechanism (when operating at half-duplex only).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 2.4 Features and Benefits Full 1000Mb, 100Mb or 10 Mb switching services for high performance Ethernet LANs Magnum CSG14 Series Switches provide Fast Ethernet switching on all ports. They perform high-speed filter/forward operations on the traffic, giving each port’s segment a full 1000Mb, 100Mb or 10 Mb of bandwidth.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) and the other RJ-45 port can be used as diagnostic port or for more connectivity. Installation is “Plug and Play”, operation is transparent to software The Magnum CSG14 Series Switches operate as hardware switches, only forwarding those packets from each domain that are needed on the other domains.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Qualified to use for temperature un-controlled “outdoor” application The Magnum CSG14P Premium rated versions of Converter Switches have an ambient temperature rating between –40C to +75C for DC models and qualify for temperature un-controlled “outdoor” application.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 2.5 Applications for CSG14 Series Converter Switches Enriched with the two tier “O-R” hardness rating flavors (Orange –“Hardened”, Red“Premium rated (outdoor)”), the multifunctional, multi-media and multi-environmental, Magnum CSG14 Series Converter Switches fit very well in almost any environment enabling users to scale their networks quickly and cost effectively.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) copper ports together with the 10, 100 or 1000Mbps fiber port choices and the availability the industry standard fiber connectors, enable easy interfacing with existing cable plant and equipment. The Magnum CSG14Ps fit very well in high temperature locations experiencing a need to scale the LAN quickly and cost effectively.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Example 1: Indoor Office CSG14 Magnum 6K25 W W W .G a r r e tt C o m .C o m Router G arr M ag num e ttC om mP6 2 G a r re M ag Server Server num ttC o mP6 m Server 2 Server IBM Compatible t tC om om 2 Port 3 A LA2 FF Port 2 .C ch L A1 F/H LK/ACT 3 L A3 PWR LK/ACT 10/ 100 re C SN w it FH1 12 V dc 0.5 Am p F/H POWER ar rS 14 u re ttC om .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) In this example, the indoor office location is a Data Mining function with an ongoing demand to grow the network. This need can be easily met using the economical Magnum CSG14 Converter Switch. Additional functionality includes the ability to transfer data across large distances with multi- or single–mode fiber while securing the LAN from EMI and wire-tapping. www . GarrettCom .
CSG14 Series Gigabit Converter Switch Example 2: CSG14H Installation and User Guide (05/08) Magnum 6K25 W WW .Gar rettCom.Com Router 12V, 1.5Amps 12V, 1.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) In this application, where in expanding an industrial network environment, the new PLC units are deployed on an existing network and each needs one (or two for redundancy) Ethernet ports to carry status and control data to the control center the hardened version of Magnum CSG14H is typically used. .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Example 3: CSG14P Magnum 6K25 W W W .G a r r e t t C o m .C o m Router 12V, 1.5Amps Magnum DS80C Personal HubDual Speed Tx F 12V, 1.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) In this example, the Magnum CSG14P Premium Converter Switches are deployed to serve as a secure corporate or transportation surveillance system. CCTV cameras may be spread out over many miles in temperature un-controlled locations and with pan, tilt and zoom (PTZ) controlled through an Ethernet copper port .
CSG14 Series Gigabit Converter Switch 3.0 Installation and User Guide (05/08) INSTALLATION This section describes the installation of the Magnum CSG14 Series Converter Switches, including location; mountings and power supply options and media connection. 3.1 Locating the Converter Switch Unit All the CSG14 Series Switches operate in transparent half-and full-duplex mode.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The compact and lightweight design of the Magnum CSG14 Series allows it to be easily installed in almost any location. A Velcro strip may be used for mounting the unit on a vertical surface such as a wall or cabinet, or for securing the unit on a table-top or shelf. Alternatively, metal mounting clips and screws are included for a rugged and secure mounting in any orientation.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 3.2 MC14-TRAY for Rack Mounting of CSG14 Series Switches For 19” rack-mounting of Magnum CSG14 Series Converter Switches, a rackmount tray is available, the MC14-TRAY. The Converter Switches are mounted with the DC power jack in the back, with the fiber and the RJ-45 connectors in the front. Any mix of the Converter Switches and/or Media Converters may be placed on a tray, up to a maximum of 16 units.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) In a typical installation, the MC14-TRAY, 19” rack-mount tray will hold a few (three to eight) CSG14 Series Converter Switches, with their power supplies plugged into power strips (not included) in the rear area of the tray. Metal mounting screws in the bottom-front hold the Converter Switches firmly in place.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The MC14-TR+PS9X2 Model has two groups of eight units per power supply. The power supplies have auto-ranging AC input for use worldwide. The side-view below is an example of an installation of the model MC14TR+PS9, 19” rack-mount tray, holding a few CSG14, FT14 and 14E Media Converters, each with their power input plugged into the built-in common AC power supply in the rear area of the tray.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Metal mounting screws in the bottom-front hold each of the media converters securing them in the tray and enabling separate removal for service. The dual LEDs permit viewing of Switch status from any angle. 3.4 DIN-Rail mounting option The Magnum CSG14HR and CSG14PR Converter Switches, designed for use in “Factory Floor” Industrial Ethernet environments, are also available for DIN-Rail mounting in an enclosure having DIN Rails.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The Magnum CSG14 models with “HR” have 24VDC power, and have the DINRail-MC2 bracket included and assembled with the MC unit at the factory. 3.5 Power Requirements, Power Supply Types for CSG14 Series Switches Magnum CSG14 Series Switches are power-efficient and can work with an external AC power supply. Magnum CSG14 Series require a nominal 12VDC input version.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) withstand higher temperature environments, and provide the DC power choices to the user to deploy in uncontrolled temperature environments. 12VDC 24VDC -48VDC The Direct DC (Internal) 12V DC (8 – 15V DC) has a built-in terminal block for +, -, ground. The 9V DC jack is also present. Detail information about the 12 VDC, the 24V DC and the –48V DC is provided in the Technical Specifications Section 1.1.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 3.6 Powering the CSG14H and CSG14P (DC internal) with 12V, 24V or –48VDC power input Each Magnum CSG14H/CSG14PSeries is reliably equipped with an internal DC power supply, and has built-in screw terminals for secure attachment of the power leads. Three models support a range of power input types. The three model choices are for use with 12VDC, 24VDC or -48VDC power. DC power input may be chosen for high-availability.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) also present and optionally can be used with an external AC power supply. DC Power Terminals: “+”, “-”, gnd GND: Terminal for “earth” or ground wire connection to the CSG14H chassis Input Voltage: 8 - 15V DC (12V DC) 18 – 36V DC (24V DC) 36 – 60V DC (-48V DC) Input current: 0.8 amp.(12V DC) 0.4 amp max.(24V DC) 0.2 amp max.(-48V DC) Power Consumption: 4 watts typical, 5 watts max. www . GarrettCom .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 3.7 CSG14H and P Series, DC-powered, -48VDC, 24VDC and 12VDC Installation This section describes the proper connection of the -48VDC leads (or 24VDC, 12VDC leads) to the DC power terminal block on the Magnum CSG14H hardened media converter (as shown in Figure). The DC terminal block on the Magnum CSG14H is located on the left side of the unit and is equipped with three (3) screw-down lead posts.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) The connection procedure is straightforward. Simply insert the DC leads to the CSG14H’s power terminals, positive (+) and negative (-) screws. The use of Ground (GND) optional; it connects to the CSG14H chassis. Ensure that each lead is securely tightened from the top, as shown here. NOTE: Always use a voltmeter to measure the voltage of the incoming power supply and figure out the +ve potential lead or -ve potential lead.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) used when making 1000BASE-T connections. When the ports are used as 10BASE-T ports, CAT 3 may be used. In either case, the maximum distance for unshielded twisted pair cabling is 100 meters (328 ft). For fiber port 10BASE-FL, 100BASE-FX or 1000BASE-SX multi-mode, 50/125 or 62.5/125 microns cabling can be used, whereas for single-mode, 9/125 microns cabling should be used.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) NOTE : It is recommended that high quality CAT. 5E cables (which work for 10Mbps, 100Mbps and 1000Mbps) be used whenever possible in order to provide flexibility in a mixed-speed network, since P80-series switch ports are autosensing for either 10,100 or 1000Mbps. Note that the auto-cross function does not operate, if the port is fixed or not supporting auto-negotiation. 3.8.
CSG14 Series Gigabit Converter Switch 4. 3.8.2 Installation and User Guide (05/08) illuminated when the unit is powered and proper connection is established. If this does not help, ensure that the cable is connected properly and that the device on the other end is powered and is not defective. For Port # 1 or 1SW, if the LINK LED is not illuminated, move the switch which has a cross-over or up-link for linking to another hub or Switch.
CSG14 Series Gigabit Converter Switch 3.8.4 Installation and User Guide (05/08) Connecting Single-Mode Fiber Optic When using single-mode fiber cable, be sure to use single-mode fiber port connectors. Single-mode fiber cable has a smaller diameter than multi-mode fiber cable (9/125 microns for single-mode, 50/125 or 62.5/125 microns for multi-mode where xx/xx are the diameters of the core and the core plus the cladding respectively).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Worst case OPB = OPB - 1dB(for LED aging) - 1dB(for insertion loss) Worst case distance = {Worst case OPB, in dB} / [Cable Loss, in dB/Km] where the “Cable Loss” for 62.5/125 and 50/125μm (m.m.) is 2.8 dB/km, and the “Cable Loss” for 100/140 (Multi-mode) is 3.3 dB/km, and the “Cable Loss” for 9/125 (Single-mode) is 0.
CSG14 Series Gigabit Converter Switch Fiber Port Module CSG14SX Speed, Std. Mode Installation and User Guide (05/08) Std. km Wavel Cable X’mitr R’cvr Worst Worst* typical typical* fdx ength Size Output Sens. OPB, distance OPB, distance (hdx) nm dB Km, fdx μm PT , dB PR ,dB dB Km, fdx 1000Mb Multimode 0.55 SX 850 62.5/125 50/125 -9.5 -17 5.5 2 12.5 4 1000Mb Single -mode LX 10 1310 9/125 -9.5 -20 8.5 17 10.5 21 CSG14LX25 1000Mb Single -mode LX 25 1310 9/125 -4.0 -21 15 37.5 17.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) * Note: The use of either multi-mode or single-mode fiber to operate at 1000Mbps speed over long distances (i.e., over approx. 400 meters) can be achieved only if the following factors are both applied: • The 1000Mb fiber segment must operate in full-duplex (FDX) mode, and • The worst-case OPB of the fiber link must be greater than the fiber cable’s passive Attenuation.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) steady ON and is OFF, for 10 or 100Mbps traffic. 4.0 OPERATION 4.1 Triple-Speed Functionality, and Switching The Magnum CSG14 Series Converter Switches provide three switched ports. The architecture supports a triple speed-switching environment, with standard autonegotiation capability. The switched RJ-45 ports are full- or half-duplex auto-sensing for mode and speed, and auto cross for plug polarity. (See Section 2.2).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) configuring to be done at installation or for maintenance. The only hardware configuration settings are user options for port #2, to configure it FF/AN. The internal functions of both are described below. Switching, Filtering and Forwarding Each time a packet arrives on one of the switched ports, the decision is taken to either filter or to forward the packet.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) eliminates bad packets and enables peak performance to be achieved when there is heavy traffic on the network. Switching, Address Learning The Magnum CSG14 Series units have address table capacity of 1K node addresses, and are suitable for use in large networks. They are self-learning, so that as nodes are added or removed or moved from one segment to another, the CSG14 Series switch automatically keeps up with node locations.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) connecting the CSG14’s to other unmanaged switches, legacy hubs, managed switches, media-converters etc. Please note that there can be conditions with managed switches where the switch manager fixes the port settings via software, and the result of the autonegotiation is changed in the managed switch by the manager commands.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) the devices connected, this will result in agreement to operate at 10Mbps, 100Mbps or 1000Mbps speed, and full- or half-duplex mode. 4.3 Dual LEDs, Front-panel and side-panel LED Description PWR Illuminates GREEN to indicate power applied. LK/ ACT Steady ON for LINK w/no traffic, blinking for activity per port.
CSG14 Series Gigabit Converter Switch 5.0 Installation and User Guide (05/08) TROUBLESHOOTING All Magnum Ethernet products are designed to provide reliability and consistently high performance in all network environments. The installation of Magnum CSG14 Series 10/100/1000 Mb/s Switches is a straightforward procedure (see INSTALLATION, Section 3.0); the operation is also straightforward and is discussed in Section 4.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) supplier for assistance or contact GarrettCom Customer Support. 5.1 Before Calling for Assistance 1. If difficulty is encountered when installing or operating the unit, refer back to the Installation Section of the applicable chapter of this manual. Also check to make sure that the various components of the network are interoperable. 2.
CSG14 Series Gigabit Converter Switch 4. Installation and User Guide (05/08) If the problem is isolated to a network device other than the Magnum CSG14 Series 10/100/1000 Mb/s switch product, it is recommended that the problem device is replaced with a known good device. Verify whether or not the problem is corrected. If not, go to Step 5 below. If the problem is corrected, the Magnum CSG14 Series Switch and its associated cables are functioning properly. 5.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) 5.2 When Calling for Assistance Please be prepared to provide the following information. 1. A complete description of the problem, including the following points: a. b. c. d. The nature and duration of the problem; Situations when the problem occurs; The components involved in the problem; Any particular application that, when used, appears to create the problem; 2.
CSG14 Series Gigabit Converter Switch 4. Installation and User Guide (05/08) A record of changes that have been made to your network configuration prior to the occurrence of the problem. Any changes to system administration procedures should all be noted in this record. 5.3 Return Material Authorization (RMA) Procedure All returns for repair must be accompanied by a Return Material Authorization (RMA) number. To obtain an RMA number, please use this URL https://rma.garrettcom.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) Packing List Number (or Sales Order Number) Date of installation Failure symptoms, including a full description of the problem. GarrettCom will carefully test and evaluate all returned products, will repair products that are under warranty at no charge, and will return the warrantyrepaired units to the sender with shipping charges prepaid (see Warranty Information, Appendix A, for complete details).
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) No Problem Found. GarrettCom reserves the right to charge for the testing of non-defective units under warranty. Testing and repair of product that is not under warranty will result in a customer (user) charge. 5.4 Shipping and Packaging Information Should you need to ship the unit back to GarrettCom, please follow these instructions: 1. Package the unit carefully. It is recommended that you use the original container if available.
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) CAUTION: Do not pack the unit in Styrofoam "popcorn" type packing material. This material may cause electro-static shock damage to the unit. 2. Clearly mark the Return Material Authorization (RMA) number on the outside of the shipping container. 3. GarrettCom is not responsible for your return shipping charges. 4. Ship the package to: GarrettCom, Inc. 47823 Westinghouse Drive Fremont, CA 94539 Attn.: Customer Service www .
CSG14 Series Gigabit Converter Switch Installation and User Guide (05/08) APPENDIX A: WARRANTY INFORMATION GarrettCom, Inc. warrants its products to be free from defects in materials and workmanship for a period of three (3) years from the date of shipment by GarrettCom.
