VECTOR™ 3 AND VECTOR 3S Owner’s Manual
© 2017 Garmin Ltd. or its subsidiaries All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
Table of Contents Introduction.....................................................................1 Thank You .................................................................................. 1 Getting Started ............................................................................ 1 Tools Needed ............................................................................. 1 Installing the Vector Components ............................................... 1 Installing the Shoe Cleats ..................
Introduction WARNING Read all instructions carefully before installing and using the Vector system. Improper use could result in serious injury. See the Important Safety and Product Information guide in the product box for product warnings and other important information. 4 Hand tighten the spindle. 5 Use the pedal wrench to tighten the spindle. NOTE: For more information, go to www.garmin.com/manuals /vector3 or www.support.garmin.com. Thank You Thank you for your Vector 3 or Vector 3S purchase.
Entering the Crank Length The crank length is often printed on the crank arm. This procedure contains instructions for the Edge 1030. If you have another compatible device, see Other Compatible Devices, page 6, or see your owner's manual. 1 Rotate the pedals a few times in order to activate Vector. > Sensors. 2 Select 3 Select your sensor. 4 Select Sensor Details > Crank Length. 5 Enter the crank length, and select . 3 Use a 4 mm hex key to loosely attach each bolt to the sole of the shoe.
• Use the USB cable that came with your Edge 1030 to send ride data to your Garmin Connect account on your computer. Garmin Connect 3 If necessary, hold a data field à to change it (Customizing the Data Fields, page 2). NOTE: The two data fields at the bottom of the screen can be customized. You can send the ride to the Garmin Connect Mobile app to view additional cycling dynamics data (Sending Your Ride to Garmin Connect, page 3). You can connect with your friends on Garmin Connect.
Device Information Vector Device Care NOTICE Keep the components clean and free of debris. Do not use a sharp object to clean the device. Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes. Do not submerge or pressure wash the components. Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Replace components with Garmin parts only. See your Garmin dealer or the Garmin website.
3 Set the battery cover and batteries Á aside. 4 Use a small Phillips screwdriver (PH 00) to remove the two screws  from inside the battery carriage Ã. 5 Remove the battery carriage. 6 While securely holding the wrench flats with a pedal wrench, use the 12 mm socket wrench to unscrew the spindle nut Ä. NOTE: The right pedal has a black spindle nut and a reverse thread. The left pedal has a silver spindle nut. The left spindle has a line on the wrench flats. 7 Slide the spindle Å out of the pedal body.
20 Install the pedals (Installing the Pedals, page 1). Vector Storage If you are transporting your bicycle or not using Vector for an extended period of time, Garmin recommends removing Vector and storing it in the product box. Other Compatible Devices Edge 1000 Instructions Pairing Vector with the Edge 1000 1 Bring the Edge device within range (3 m) of the sensor. NOTE: Stay 10 m away from other ANT+ sensors while pairing. 2 Turn on the Edge device.
Power Data Fields NOTE: This list contains power data fields for the Edge 1030 device. If you have another compatible device, see your device owner's manual. NOTE: Data fields that display pedal smoothness, torque effectiveness, and balance data are not supported by the Vector S system. Balance: The current left/right power balance. Balance - 10s Avg.: The 10-second moving average of the left/ right power balance. Balance - 30s Avg.: The 30-second moving average of the left/ right power balance.
Troubleshooting Updating the Vector Software Using the Edge 520, 820, 1000, or 1030 Before you can update the software, you must pair your Edge device to your Vector system. NOTE: The left pedal receives the software update. The left pedal sends the update to the right pedal. 1 Send your ride data to your Garmin Connect account. Garmin Connect automatically looks for software updates and sends them to your Edge device. 2 Bring your Edge device within range (3 m) of the sensor.
Index B battery 1 life 4 replacing 4 C calibrating 2, 6 cleaning the device 4 cleats 1 customizing the device 2 cycling dynamics 2 D data storing 3 transferring 3 data fields 2, 7 E Edge 2, 6 F fēnix 6 Forerunner 6 G Garmin Connect 3 H history 3 sending to computer 3 I installing 1 M maintenance 4 memory 3 P pairing 1, 2, 6 smartphone 3 pedals 1, 2, 4 platform center offset 3 power 2 power (force), meters 2 power phase 3 product registration 6 R registering the device 6 resetting the device 8 S s
support.garmin.
