Vector and Vector S ™ Owner’s Manual September 2014 Printed in Taiwan 190-01450-00_0D
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product. Garmin®, Edge®, and the Garmin logo are trademarks of Garmin Ltd.
Table of Contents Introduction.................................................................... 1 Thank You .................................................................................. 1 Getting Started ........................................................................... 1 Tools Needed ............................................................................. 1 Installing the Vector Components .............................................. 1 Preparing the Crank Arms ......................
Introduction NOTE: Do not use more than two washers. WARNING Read all instructions carefully before installing and using the Vector system. Improper use could result in serious injury. See the Important Safety and Product Information guide in the product box for product warnings and other important information. NOTICE Go to www.garmin.com/vectorowner for the latest information including bike compatibility, software updates, and video tutorials.
NOTE: Garmin recommends torque of 25 to 30 lbf-ft. (34 to 40 N-m). 7 Firmly plug the cable into the spindle. 8 Rotate the crank arm to check for clearance. Installing the Right Pedal 3 On the pedal spindle, stack the pedal pod and any required washers Â. TIP: You must carefully bend the cable à out of the way. 4 Insert the spindle into the crank arm Ä. 5 Hand tighten the spindle. NOTE: The left pedal spindle has a left-handed (reverse) thread.
3 From the home screen, select > Sensors > Add Sensor > Power. 4 Rotate the crank arm a few times. When the sensor is paired with your Edge device, the sensor status is Connected. You can customize a data field to display Vector data. Your First Ride Before you ride with Vector for the first time, you must enter the crank length, set the installation angle of the sensors inside the pedals, and calibrate the static zero reference. You must also calibrate the system if you move Vector to another bike.
Analyze your data: You can view more detailed information about your activity, including time, distance, elevation, heart rate, calories burned, cadence, an overhead map view, pace and speed charts, and customizable reports. NOTE: Some data requires an optional accessory such as a heart rate monitor. Plan your training: You can choose a fitness goal and load one of the day-by-day training plans.
Apply a layer of bike grease to the spindle. 10 Insert the spindle into the cartridge. 11 Wipe away any excess grease. 12 Install the new washer and nut on the end of the spindle. NOTE: Always replace both batteries at the same time. 1 Locate the circular battery cover À on the back of the pedal pod. NOTE: The nut for the right spindle has a left-handed (reverse) thread. 13 Use the hex nut driver to tighten the nut. WARNING Garmin recommends torque of 7 lbf-ft. (10 N-m).
When the sensor is paired with your Edge device, the sensor status is Connected. You can customize a data field to display Vector data. Entering the Crank Length The crank length is often printed on the crank arm. 1 Rotate the pedals a few times in order to activate Vector. 2 From the home screen, select > Bike Profiles. 3 Select a profile. 4 Select Crank Length > Manual. 5 Enter the crank length, and select .
Balance - 10s Avg.: The 10-second moving average of the left/ right power balance. Balance - 30s Avg.: The 30-second moving average of the left/ right power balance. Balance - 3s Avg.: The three-second moving average of the left/right power balance. Balance - Avg.: The average left/right power balance for the current activity. Balance - Lap: The average left/right power balance for the current lap. Cadence: The number of revolutions of the crank arm or number of strides per minute.
Index B battery life 5 replacing 5 type 5 C calibrating 3, 6 cleaning the device 4 cleats 2 compatibility 7 customizing the device 3, 6 D data storing 3 transferring 3 data fields 3, 6 E Edge 2, 5, 6 G Garmin Connect 3 H history 3 sending to computer 3 I installing 1, 2 M memory 3 P pairing 2, 5, 6 pedal pods 1, 2, 4, 5 pedals 1–4 power 3 product registration 5 R registering the device 5 replacement parts 4 S software, updating 7 specifications 5 storing data 3 storing the device 4, 5 T tools 1 t
www.garmin.
