G1000 ® Integrated Flight Deck Cockpit Reference Guide for the Piper PA-44-180 Seminole
FLIGHT INSTRUMENTS ENGINE INDICATION SYSTEM NAV/COM/TRANSPONDER/AUDIO PANEL GPS NAVIGATION FLIGHT PLANNING PROCEDURES HAZARD AVOIDANCE ADDITIONAL FEATURES ABNORMAL OPERATION ANNUNCIATIONS & ALERTS APPENDIX INDEX
Copyright © 2013 Garmin Ltd. or its subsidiaries. All rights reserved. This manual reflects the operation of System Software version 1648.01 or later for the Piper PA-44-180 Seminole. Some differences in operation may be observed when comparing the information in this manual to earlier or later software versions. Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel: 913/397.8200 Fax: 913/397.8282 Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A. Tel: 503/391.
AOPA Membership Publications, Inc. and its related organizations (hereinafter collectively “AOPA”) expressly disclaim all warranties, with respect to the AOPA information included in this data, express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. The information is provided “as is” and AOPA does not warrant or make any representations regarding its accuracy, reliability, or otherwise.
Warnings, Cautions & Notes WARNING: Do not use the terrain avoidance feature as the sole means of navigation and terrain separation. The terrain avoidance feature is only to be used as and aid to terrain avoidance. Garmin obtains terrain database content from third party sources and is not able to independently verify the accuracy of the terrain data. WARNING: Do not rely on the displayed minimum safe altitude (MSAs) as the sole source of obstacle and terrain avoidance information.
Warnings, Cautions & Notes WARNING: Do not use data link weather information for maneuvering in, near or around areas of hazardous weather. Information contained within data link weather products may not accurately depict current weather conditions. WARNING: Do not use the indicated data link weather product age to determine the age of the weather information shown by the data link weather product.
Warnings, Cautions & Notes WARNING: To reduce the risk of unsafe operation, carefully review and understand all aspects of the Pilot’s Guide documentation and the Airplane Flight Manual. Thoroughly practice basic operation prior to actual use. During flight operations, carefully compare indications from the system to all available navigation sources, including the information from other NAVAIDs, visual sightings, charts, etc.
Warnings, Cautions & Notes CAUTION: The PFD and MFD displays use a lens coated with a special anti-reflective coating that is very sensitive to skin oils, waxes, and abrasive cleaners. CLEANERS CONTAINING AMMONIA WILL HARM THE ANTIREFLECTIVE COATING. It is very important to clean the lens using a clean, lint-free cloth and an eyeglass lens cleaner that is specified as safe for antireflective coatings. CAUTION: The system does not contain any user-serviceable parts.
Warnings, Cautions & Notes NOTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our web site at www.garmin.com/prop65.
Warnings, Cautions & Notes Blank Page Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Record of Revisions Part Number 190-01462-00 Change Summary Initial release Revision Date of Revision Affected Pages A June, 2013 All 190-01462-00 Rev.
Record of Revisions Blank Page RR-2 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Table of Contents FLIGHT INSTRUMENTS................................................................................................................. 1 Selecting the Altimeter Barometric Pressure Setting....................................................... 1 Selecting Standard Barometric Pressure (29.92 in Hg)..................................................... 1 Change Altimeter Barometric Pressure Setting Units....................................................... 1 Change Navigation Sources..........
Table of Contents Enter an Airway in a Flight Plan........................................................................................... 31 User-Defined Holding Patterns............................................................................................. 31 Invert An Active Flight Plan................................................................................................... 34 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan......................
Table of Contents ABNORMAL OPERATION.......................................................................................................... 69 Reversionary Mode................................................................................................................. 69 Abnormal COM Operation..................................................................................................... 69 Hazard Displays with Loss of GPS Position................................................................
Table of Contents Blank Page iv Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Flight Instruments Flight Instruments FLIGHT INSTRUMENTS SELECTING THE ALTIMETER BAROMETRIC PRESSURE SETTING EIS Turn the BARO Knob to select the desired setting. Nav/Com/ XPDR/Audio SELECTING STANDARD BAROMETRIC PRESSURE (29.92 IN HG) 1) Press the PFD Softkey. 2) Press the STD BARO Softkey to set standard barometric pressure. GPS Nav CHANGE ALTIMETER BAROMETRIC PRESSURE SETTING UNITS Flight Planning 1) Press the PFD Softkey to display the second-level softkeys.
ENABLE/DISABLE OBS MODE WHILE NAVIGATING WITH GPS 1) Press the OBS Softkey to select OBS Mode. 2) Turn a CRS Knob to select the desired course to/from the waypoint. Press the CRS Knob to synchronize the Selected Course with the bearing to the next waypoint. 3) Press the OBS Softkey again to disable OBS Mode. GENERIC TIMER 1) Press the TMR/REF Softkey, then turn the large FMS Knob to select the time field (hh/mm/ss). Turn the FMS Knobs to set the desired time, then press the ENT Key.
Flight Instruments Flight Instruments 5) If TEMP COMP was selected, press the ENT Key or turn the large FMS Knob to highlight the next field and then enter the destination airport temperature (-59˚C to 59˚C). The temperature compensated altitude minimum is displayed below the previously enter minimum altitude value. EIS 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Nav/Com/ XPDR/Audio DISPLAYING WIND DATA 1) Press the PFD Softkey.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Flight Instruments Blank Page 4 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
EIS Flight Instruments ENGINE INDICATION ENGINE DISPLAY EIS Nav/Com/ XPDR/Audio 1 GPS Nav 2 3 Flight Planning 4 5 Procedures 6 Hazard Avoidance 7 8 Additional Features 9 10 Abnormal Operation 11 Annun/Alerts 12 Engine Display when Engine Page is displayed Appendix Engine Display Index 190-01462-00 Rev.
1 Engine Manifold Pressure Gauge (MAN IN HG) Displays manifold pressure in inches of Mercury (in Hg) to indicate engine power 2 Tachometer (RPM) Displays propeller speed in revolutions per minute (rpm) 3 Propeller Sync Indicator Points towards the higher-speed propeller when the propellers are out of sync.
EIS Press the ENGINE Softkey or turn the large FMS Knob and select the EIS - Engine Page. 13 12 EIS 14 Flight Instruments ENGINE PAGE Nav/Com/ XPDR/Audio 1 2 3 GPS Nav 4 5 Flight Planning 11 6 10 Procedures 7 9 Hazard Avoidance 8 Engine Page Displays propeller speed in revolutions per minute (rpm) 3 Propeller Sync Indicator Points towards the higher-speed propeller when the propellers are out of sync.
6 Oil Pressure Indicator (OIL PSI) 7 Displays oil temperature in degrees Fahrenheit (°F) Oil Temperature Indicator (OIL °F) 8 Displays landing gear status Landing Gear Status (LANDING GEAR) 9 Fuel Calculations Group (FUEL CALC) Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments EIS 10 Electrical Group Procedures (ELECTRICAL) 11 Engine Hours Hazard Avoidance (TACH TIME) 12 Exhaust Gas Additional Features 13 Cylinder Head Abnormal Operation Temperature (EGT °F) 14 Fuel Qu
EIS NOTE: Fuel calculations do not use the aircraft fuel quantity indicators and are calculated from the last time the fuel was reset. Flight Instruments Fuel Calculations EIS Flight Planning Procedures Resetting the fuel totalizer: On the Engine Page, select the RST FUEL Softkey; this resets displayed fuel remaining (GAL REM) to the maximum fuel capacity for the aircraft and fuel used to zero.
Flight Instruments EIS LANDING GEAR INDICATIONS Landing Gear statuses are shown using the indications in the following table. EIS Engine Page EIS Position GPS Nav Nav/Com/ XPDR/Audio Up & Locked Procedures Flight Planning In Transition Additional Features Hazard Avoidance Down and Locked Abnormal Operation Gear Failure Index Appendix Annun/Alerts Landing Gear Indications 10 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Nav/Com/XPDR/Audio Panel Flight Instruments NAV/COM/TRANSPONDER/AUDIO PANEL ENTER A TRANSPONDER CODE Flight Planning DME TUNING GPS Nav 3) Press the digit softkeys to enter the code in the code field. When entering the code, the next key in sequence must be pressed within 10 seconds, or the entry is cancelled and restored to the previous code. Five seconds after the fourth digit has been entered, the transponder code becomes active.
NAV/COM TUNING 1) Press the small tuning knob to select the desired radio for tuning. A light blue box highlights the radio frequency to be tuned. 2) Turn the respective tuning knobs to enter the desired frequency into the standby frequency field. The large knob enters MHz and the small knob enters kHz. 3) Press the Frequency Transfer Key to place the frequency into the active frequency field.
Nav/Com/XPDR/Audio Panel Press the PILOT and/or COPLT Key to select those isolated from hearing the Nav/ Com radios.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Nav/Com/XPDR/Audio Panel Blank Page 14 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
GPS Navigation Flight Instruments GPS NAVIGATION DIRECT-TO NAVIGATION EIS Direct-to Navigation using the MFD 2) 3) 6) 7) 11) 12) Additional Features 10) Hazard Avoidance 9) Procedures 8) Flight Planning 5) GPS Nav 4) ) Key on the MFD. Enter the waypoint identifier. Press the ENT Key to confirm the identifier. The ‘Activate?’ field is highlighted. If no altitude constraint or course is desired, press the ENT Key to activate. To enter an altitude constraint, proceed to step 5.
GPS Navigation Flight Instruments 7) Turn the small FMS Knob to enter the desired altitude. 8) Press the ENT Key. If the waypoint entered is an airport, the option to select MSL or AGL is now displayed. If the waypoint is not an airport, proceed to step 10. EIS 9) Turn the small FMS Knob to select ‘MSL’ or ‘AGL’. Nav/Com/ XPDR/Audio 10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field. 11) Turn the small FMS Knob to enter the desired target altitude offset from the selected Direct-to.
GPS Navigation Flight Instruments STOP NAVIGATING A FLIGHT PLAN 1) Press the FPL Key to display the Active Flight Plan Page. 2) Press the MENU Key to display the Page Menu Window. NOTE: Temperature Compensated (TEMP COMP) altitudes are depicted as slanted text. Flight Planning GPS Nav The navigation database only contains altitudes for procedures that call for “Cross at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the database.
Altitudes associated with approach procedures are “auto-designated”. This means the system will automatically use the altitudes loaded with the approach for giving vertical flight path guidance outside the FAF. Note these altitudes are displayed as small light blue text. Altitudes associated with arrival procedures are “manually-designated”. This means the system will not use the altitudes loaded with the arrival for giving vertical flight path guidance until designated to do so by the pilot.
GPS Navigation Light Blue Text Light Blue Subdued Text Large Text Altitude calculated by the system estimating the altitude of the aircraft as it passes over the navigation point. This altitude is provided as a reference and is not designated to be used in determining vertical flight path guidance. Altitude has been entered by the pilot. Altitude is designated for use in giving vertical flight path guidance.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments GPS Navigation Blank Page 20 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Flight Planning Flight Instruments FLIGHT PLANNING WEIGHT PLANNING EIS All procedures apply to the MFD unless otherwise stated. Entering Weight Parameters Procedures Hazard Avoidance 3) Turn the small FMS Knob to enter the desired fuel quantity. 4) Press the ENT Key. The cursor is now in the ‘FUEL RESERVES’ field. Abnormal Operation 5) Turn the small FMS Knob to enter the desired reserve fuel quantity.
Flight Planning Flight Instruments 4) For Direct-to planning: a) Press the WPTS Softkey and verify that the starting waypoint field indicates ‘P.POS’ (present position). EIS b) If necessary, press the MENU Key and select ‘Set WPT to Present Position’ to display ‘P.POS’. Nav/Com/ XPDR/Audio c) Press the ENT Key and the flashing cursor moves to the ending waypoint field. GPS Nav d) Enter the identifier of the ending waypoint and press the ENT Key to accept the waypoint.
Flight Planning Abnormal Operation Annun/Alerts 2) Turn the small FMS Knob to select the User WPT Information Page. Appendix 3) Press the NEW Softkey. A waypoint is created at the current aircraft position. 4) Enter the desired waypoint name. Index 5) Press the ENT Key. 6) The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint can be made temporary (deleted automatically when the system is turned off). If the waypoint is to remain in the system, proceed to step 7.
Flight Planning Flight Instruments a) Turn the large FMS Knob one click to the left to highlight ‘TEMPORARY’. EIS b) Press the ENT Key to place a check-mark in the box. Turn the large FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field. 8) Turn the small FMS Knob to select LAT/LON (latitude and longitude). 9) Press the ENT Key. CREATE A USER WAYPOINT DEFINED BY RADIALS FROM OTHER WAYPOINTS 1) Turn the large FMS Knob on the MFD to select the ‘WPT’ page group.
Flight Planning Or: a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed. EIS b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to the aircraft’s current position. Nav/Com/ XPDR/Audio c) Turn the large FMS Knob to select the desired waypoint. d) Press the ENT Key. Or: Flight Planning b) Turn the small FMS Knob to the right to display the ‘RECENT’ waypoints. GPS Nav a) Turn the small FMS Knob to the left.
Flight Planning Flight Instruments 3) Press the NEW Softkey. A waypoint is created at the current aircraft position. 4) Enter the desired waypoint name. EIS 5) Press the ENT Key. Nav/Com/ XPDR/Audio 6) The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint can be made temporary (deleted automatically when the system is turned off). If the waypoint is to remain in the system, proceed to step 7. GPS Nav a) Turn the large FMS Knob one click to the left to highlight ‘TEMPORARY’.
Flight Planning Flight Instruments c) Turn the large FMS Knob to select the desired waypoint. d) Press the ENT Key. Or: c) Turn the large FMS Knob to select the desired waypoint. d) Press the ENT Key. Flight Planning 12) Press the ENT Key. 13) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired distance from the reference waypoint. Procedures 14) Press the ENT Key. 15) Press the FMS Knob to remove the flashing cursor.
Flight Planning Flight Instruments 7) If desired, change the storage method of the waypoint to “TEMPORARY” or “NORMAL” by moving the cursor to “TEMPORARY” and pressing the ENT Key to check or uncheck the box. 9) Press the GO BACK Softkey to return to the map page. DELETE A USER WAYPOINT 1) Turn the large FMS Knob to select the ‘WPT’ page group. 2) Turn the small FMS Knob to select the User WPT Information Page. GPS Nav Nav/Com/ XPDR/Audio EIS 8) Press the FMS Knob to remove the flashing cursor.
Flight Planning Hazard Avoidance Additional Features Abnormal Operation 5) Turn either FMS Knob to highlight an empty or existing flight plan. 6) Press the IMPORT Softkey. If an empty flight plan is selected, a list of the available flight plans on the SD card will be displayed. Annun/Alerts Procedures 4) Press the FMS Knob to activate the cursor. Flight Planning 3) Turn the small FMS Knob to select the Flight Plan Catalog Page.
Flight Planning EIS Flight Instruments 7) Turn the small FMS Knob to highlight the desired flight plan for importing. 8) Press the ENT Key. INSERT A WAYPOINT IN THE ACTIVE FLIGHT PLAN 1) Press the FPL Key to display the active flight plan. Nav/Com/ XPDR/Audio 2) If necessary, press the FMS Knob to activate the cursor. GPS Nav 3) Turn the large FMS Knob to highlight the desired flight plan waypoint.
Flight Planning Flight Instruments c) Turn the large FMS Knob to select the desired user waypoint. d) Press the ENT Key. 6) Press the ENT Key again to “accept” the waypoint. EIS ENTER AN AIRWAY IN A FLIGHT PLAN 2) Press the FMS Knob to activate the cursor (not required on the PFD). Abnormal Operation USER-DEFINED HOLDING PATTERNS 1) Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active Flight Plan Window (PFD).
Flight Planning Flight Instruments 3) Press the MENU Key, highlight ‘Hold At Waypoint’, and press the ENT Key. The HOLD AT window appears with the course field highlighted. 4) Use the FMS Knobs to edit the entry course, and press the ENT Key. EIS 5) Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course direction, and press the ENT Key. Nav/Com/ XPDR/Audio 6) Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press the ENT Key.
Flight Planning Flight Instruments Creating a user-defined hold at a Direct To waypoint: 1) Press a Direct-to Key and set up the Direct To waypoint as desired, but select ‘HOLD?’ instead of ‘ACTIVATE?’ when finished (MFD or PFD). EIS 2) Use the FMS Knobs to edit the entry course, and press the ENT Key. 4) Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press the ENT Key. GPS Nav 5) Use the FMS Knobs to edit the length, and press the ENT Key.
Flight Instruments Flight Planning INVERT AN ACTIVE FLIGHT PLAN 1) Press the FPL Key to display the active flight plan. 2) Press the MENU Key to display the Page Menu. EIS 3) Turn the large FMS Knob to highlight ‘Invert Flight Plan’. 5) With ‘OK’ highlighted, press the ENT Key to invert the flight plan. REMOVE A DEPARTURE, ARRIVAL, APPROACH, OR AIRWAY FROM A FLIGHT PLAN 1) Press the FPL Key to display the active flight plan. Press the FMS Knob to activate the cursor.
Flight Planning 1) Press the FPL Key for the MFD and turn the small FMS Knob to display the Flight Plan Catalog Page. EIS 2) Press the FMS Knob to activate the cursor. Flight Instruments EDIT A STORED FLIGHT PLAN 3) Turn the large FMS Knob to highlight the desired flight plan. Nav/Com/ XPDR/Audio 4) Press the EDIT Softkey. 5) Turn the large FMS Knob to place the cursor in the desired location. GPS Nav 6) Enter the changes, then press the ENT Key.
Flight Instruments Flight Planning INVERT AND ACTIVATE A STORED FLIGHT PLAN 1) Press the FPL Key for the MFD. EIS 2) Turn the small FMS Knob to select the Flight Plan Catalog Page. 3) Press the FMS Knob to activate the cursor. Nav/Com/ XPDR/Audio 4) Turn the large FMS Knob to highlight the desired flight plan. 5) Press the INVERT Softkey. ‘Invert and activate stored flight plan?’ is displayed. COPY A FLIGHT PLAN 1) Press the FPL Key for the MFD.
Flight Planning Flight Instruments GRAPHICAL FLIGHT PLAN CREATION 1) Press the FPL Key to display the Active Flight Plan Page on the MFD. 2) Press the FPL Key on the Control Unit to display the Active Flight Plan Page on the MFD. Additional Features 3) Turn the small FMS Knob to select the Flight Plan Catalog Page. Hazard Avoidance 1) Insert the SD card into the top card slot on the MFD.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Flight Planning Blank Page 38 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Procedures Flight Instruments PROCEDURES LOAD AND ACTIVATE A DEPARTURE PROCEDURE EIS 1) Press the PROC Key. 3) Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a list of available departures. 5) Press the ENT Key. A list of runways may be displayed for the departure. If so, turn either FMS Knob to select the desired runway. Flight Planning 6) Press the ENT Key. The cursor is displayed in the ‘TRANSITION’ field with a list of available transitions.
Procedures Flight Instruments 4) Turn the large FMS Knob to highlight the desired arrival. 5) Press the ENT Key. A list of transitions is displayed for the selected arrival. 6) Turn either FMS Knob to select the desired transition. EIS 7) Press the ENT Key. A list of runways may be displayed for the selected arrival. Nav/Com/ XPDR/Audio 8) Turn the large FMS Knob to highlight the desired runway. 9) Press the ENT Key. 10) With ‘LOAD?’ highlighted, press the ENT Key.
Procedures EIS b) Use the FMS Knob to enter the approach channel number, and press the ENT Key to accept the approach channel number. The airport and approach are selected. Flight Instruments a) If necessary, push the FMS Knob to exit the approach list, and use the large FMS Knob to move the cursor to the APPROACH CHANNEL field. Nav/Com/ XPDR/Audio 4) A list of available transitions for the selected approach procedure is now displayed.
ACTIVATE AN APPROACH IN THE ACTIVE FLIGHT PLAN 1) Press the PROC Key. 2) Turn the large FMS Knob to highlight ‘ACTIVATE APPROACH’. 3) Press the ENT Key. ACTIVATE A VECTOR TO FINAL APPROACH FIX 1) Press the PROC Key. 2) Turn the large FMS Knob to highlight ‘ACTIVATE VECTOR-TO-FINAL’. GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Procedures 3) Press the ENT Key. ACTIVATE A MISSED APPROACH IN THE ACTIVE FLIGHT PLAN 1) Press the PROC Key.
Procedures Flight Instruments Enabling temperature compensated altitude: 1) From the Active Flight Plan Page, press the MENU Key. The Page Menu is displayed. 2) Turn the FMS Knob to highlight ‘Temperature Compensation’. 3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is displayed. EIS compensated altitude is computed as the temperature is selected. GPS Nav 5) Press the ENT Key. ‘ACTIVATE COMPENSATION?’ is highlighted.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Procedures Blank Page 44 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Hazard Avoidance Flight Instruments HAZARD AVOIDANCE Customizing THE HAZARD DISPLAYS ON THE NAVIGATION MAP EIS 3) Press the small FMS Knob to return to the Navigation Map Page. Flight Planning SIRIUSXM WEATHER (OPTIONAL) GPS Nav 2) Press the ENT Key. The Map Setup Menu is displayed. Turn the small FMS Knob to select ‘Weather’ to customize the display of weather features. Select ‘Traffic’ to customize the display of traffic.
Hazard Avoidance Flight Instruments Displaying Weather on the SiriusXM Weather Data Link Page 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the SiriusXM Weather Data Link Page. EIS 3) Press the available softkeys to select the desired SiriusXM Weather product. Nav/Com/ XPDR/Audio 4) Press the LEGEND Softkey to view the legends for the selected products. If necessary, turn either FMS Knob to scroll through the list.
Hazard Avoidance Wx Product Status Icons Flight Instruments SiriusXM Weather Products and Symbols Description EIS NEXRAD - Available for the US and Canada. The age of the displayed data for each is shown at the right. Nav/Com/ XPDR/Audio ECHO TOP - The age of the displayed data is shown at the right. Not displayed when CLOUD TOP is displayed. GPS Nav CLOUD TOP - The age of the displayed data is shown at the right. Not displayed when ECHO TOP is displayed.
Flight Instruments Hazard Avoidance Wx Product Status Icons EIS PIREP - The age of the displayed data is shown at the right. Urgent Pireps are displayed in yellow. Nav/Com/ XPDR/Audio TURBULENCE - The age of the displayed data is shown at the right. The altitude selection is shown at the bottom. GPS Nav ICING POTENTIAL - The age of the displayed data is shown at the right. The altitude selection is shown at the bottom.
Hazard Avoidance Flight Instruments Traffic Symbol Description Traffic Advisory (TA) (closing rate, distance, and vertical separation meet TA criteria) EIS Traffic Advisory Off Scale Nav/Com/ XPDR/Audio Traffic Symbol Description GPS Nav Traffic Information Service (TIS) NOTE: Traffic Information Service (TIS) is only available when the aircraft is within the service volume of a TIS capable terminal radar site.
Hazard Avoidance Flight Instruments GTS 800 (Optional) Nav/Com/ XPDR/Audio EIS WARNING: The Traffic Advisory System (TAS) is intended for advisory use only to aid the pilot in visually acquiring traffic. No avoidance maneuvers should be based solely upon TAS traffic information. It is the responsibility of the pilot in command to see and maneuver to avoid traffic. Flight Planning GPS Nav NOTE: Pilots should be aware of TAS system limitations.
Hazard Avoidance Flight Instruments 6) Turn the RANGE Knob clockwise to display a larger area or counterclockwise to display a smaller area. Displaying Traffic on the Navigation Map EIS 1) Ensure TAS is operating. Nav/Com/ XPDR/Audio 2) With the Navigation Map displayed, press the MAP Softkey. 3) Press the TRAFFIC Softkey. Traffic is now displayed on the map. NOTE: A 1090 MHz extended squitter transponder is required to display ADS-B symbology for aircraft providing ADS-B data.
Flight Instruments Hazard Avoidance TERRAIN AND OBSTACLE PROXIMITY NOTE: Terrain data is not displayed when the aircraft is outside the installed terrain database coverage area. EIS Nav/Com/ XPDR/Audio Displaying Terrain and Obstacles on the Terrain Proximity Page 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the Terrain Proximity Page. GPS Nav 3) If desired, press the VIEW Softkey to access the ARC and 360 Softkeys.
Hazard Avoidance NOTE: Terrain-SVS is only available when the Synthetic Vision Technology (SVT) option is installed and the TAWS-B option has not been installed. NOTE: Terrain data is not displayed when the aircraft is outside the installed terrain database coverage area. EIS Flight Instruments TERRAIN-SVS GPS Nav 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the Terrain-SVS Page.
Hazard Avoidance Flight Instruments Terrain-SVS Inhibit Nav/Com/ XPDR/Audio EIS Inhibit Terrain While the Terrain-SVS Page is displayed, press the INHIBIT Softkey. Or: 1) Press the MENU Key. 2) Turn the small FMS Knob to select ‘Inhibit Terrain’. 3) Press the ENT Key. Procedures Flight Planning GPS Nav Enable Terrain While the Terrain-SVS Page is displayed, press the INHIBIT Softkey. Or: 1) While the Terrain-SVS Page is displayed, press the MENU Key.
Hazard Avoidance NOTE: TAWS-B operation is only available when the G1000 is configured for a TAWS-B installation. Flight Planning Manual System Test 1) While the TAWS-B Page is displayed, press the MENU Key. Procedures 2) Turn the small FMS Knob to select ‘Test TAWS’. 3) Press the ENT Key. During the test ‘TAWS TEST’ is displayed in the center of the TAWS-B Page. Hazard Avoidance When all is in working order, “TAWS System Test, OK” is heard.
Hazard Avoidance Flight Instruments Enable/Disable Aviation Data 1) While the TAWS-B Page is displayed, press the MENU Key. EIS 2) Turn the small FMS Knob to select “Show (or Hide) Aviation Data”. 3) Press the ENT Key.
Additional Features Flight Instruments ADDITIONAL FEATURES SYNTHETIC VISION (OPTIONAL) Procedures Hazard Avoidance Additional Features Abnormal Operation Pathways Flight Path Marker Horizon Heading Marks Terrain and Obstacle Alerting Three-dimensional Traffic Airport Signs Runway Display Flight Planning Annun/Alerts • • • • • • • GPS Nav Synthetic Vision Technology (SVT) functionality is offered as an optional enhancement to the G1000 Integrated Flight Deck System.
Additional Features Flight Instruments Displaying Pathways 1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. EIS 3) If not already enabled, press the SYN TERR Softkey. Nav/Com/ XPDR/Audio 4) Press the PATHWAY Softkey. 5) Press the BACK Softkey to return to the previous page. Displaying Heading on the Horizon GPS Nav 1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. Flight Planning 3) If not already enabled, press the SYN TERR Softkey. 4) Press the HRZN HDG Softkey.
Additional Features Index 3) Press the GO BACK Softkey to return to the previous page. 190-01462-00 Rev. A Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole Appendix 2) Press the DP, STAR, APR, WX, and NOTAM softkeys to access charts for departures, arrivals, approaches, weather and NOTAMs Note that NOTAMS are only available with ChartView. Annun/Alerts Move the map pointer to point to a desired point on the map and press the SHW CHRT Softkey.
Additional Features Flight Instruments View Charts from the Active Flight Plan Page 1) While viewing the Active Flight Plan Page, press the FMS Knob to activate the cursor. EIS 2) Turn the large FMS Knob to select the departure airport, destination airport, departure, arrival, or approach. Nav/Com/ XPDR/Audio 3) Press the SHW CHRT Softkey. The appropriate chart is displayed, if available for the item selected. GPS Nav 4) Press the GO BACK Softkey to return to the previous page.
Additional Features Flight Instruments View Airport Directory Information EIS While viewing the WPT-Airport Information Page, if necessary, press the INFO-1 Softkey to change the softkey label to display INFO-2. Airport information is displayed on the right half of the display. The XM Radio Page provides information and control of the audio entertainment features of the SiriusXM Satellite Radio.
Additional Features Flight Instruments Or: Press the FMS Knob to highlight the channel list and turn the large FMS Knob to scroll through the channels. EIS 3) With the desired channel highlighted, press the ENT Key. Nav/Com/ XPDR/Audio Entering a Channel Directly 1) While on the XM Radio Page, press the CHNL Softkey. GPS Nav 2) Press the DIR CH Softkey. The channel number in the Active Channel Box is highlighted.
Additional Features 4) Use the FMS Knob to enter the message text to be displayed in the Messages Window and press the ENT Key. 6) Turn the small FMS Knob to select the message type: Hazard Avoidance • Event—Message issued at the specified date/time • One-time—Message issued when the message timer reaches zero (default setting) 8) For periodic and one-time message, use the FMS Knob to enter the timer value (HH:MM:SS) from which to countdown and press the ENT Key.
Additional Features Flight Instruments Deleting a Scheduler Message 1) Select the AUX - Utility Page. EIS 2) Press the FMS Knob momentarily to activate the flashing cursor. 4) Press the CLR Key to clear the message text. If the CLR Key is pressed again, the message is restored. 5) Press the ENT Key while the message line is cleared to clear the message time. When a scheduler message is waiting, the MSG Softkey flashes.
Additional Features Flight Instruments 8) With ‘CREATE’ highlighted, press the ENT Key to create the profile Or: EIS Use the large FMS Knob to select ‘CREATE and ACTIVATE’ and press the ENT Key to activate the new profile. Selecting an active profile: GPS Nav 1) Use the FMS Knob to select the AUX - System Setup Page. Nav/Com/ XPDR/Audio 9) To cancel the process, select ‘CANCEL’ with the large FMS Knob and press the ENT Key. 2) Press the FMS Knob momentarily to activate the flashing cursor.
Additional Features Flight Instruments Deleting a profile: 1) Use the FMS Knob to select the AUX - System Setup Page. EIS 2) Press the FMS Knob momentarily to activate the flashing cursor. 3) Turn the large FMS Knob to highlight ‘DELETE’ in the Pilot Profile Box. Nav/Com/ XPDR/Audio 4) Press the ENT Key. 5) In the ‘Delete Profile’ window, turn the FMS Knob to select the profile to delete. GPS Nav 6) Press the ENT Key. 7) With ‘DELETE’ highlighted, press the ENT Key.
Additional Features 2) Use the FMS Knob to select the AUX - System Setup Page. 4) Press the EXPORT softkey. GPS Nav 5) With ‘EXPORT’ highlighted press the ENT Key. Nav/Com/ XPDR/Audio 3) Activate the desired Pilot Profile to export. Only the active Pilot Profile can be exported. EIS 1) Insert the SD card for storing the Pilot Profile into the top card slot on the MFD. Flight Instruments Exporting a profile: 6) “Pilot profile export succeeded.” is shown in the export results box.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Additional Features Blank Page 68 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Abnormal Operation Flight Instruments ABNORMAL OPERATION REVERSIONARY MODE GPS Nav • MFD failure – PFD automatically enters reversionary mode. Flight Planning • Reversionary display mode can be manually activated by pressing the DISPLAY BACKUP Button on the audio panel. When the DISPLAY BACKUP Button is selected both displays enter reversionay display mode. NOTE: The PA-44-180 Seminole Pilot’s Operating Handbook (POH) always takes precedence over the information found in this section.
UNUSUAL ATTITUDES The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary functions are displayed in these situations.
Abnormal Operation Nav/Com/ XPDR/Audio GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/Alerts DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’ superimposed in yellow over the ‘own aircraft’ symbol as shown in the following figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly above and to the right of the aircraft symbol on the CDI as shown in the following figure.
As a result of operating in DR Mode, all GPS-derived data is computed based upon an estimated position and is displayed as yellow text on the display to denote degraded navigation source information.
Annunciations & Alerts Flight Instruments ANNUNCIATIONS & ALERTS G1000 SYSTEM ANNUNCIATIONS GPS Nav Comment Nav/Com/ XPDR/Audio System Annunciation EIS When an LRU or an LRU function fails, a large red “X” is typically displayed on windows associated with the failed data. Refer to the PA-44-180 Archer Pilot’s Operating Handbook (POH) for additional information regarding pilot responses to these annunciations Flight Planning Attitude and Heading Reference System is aligning.
System Annunciation Comment Display system is not receiving airspeed input from air data computer. GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Procedures Flight Planning Display system is not receiving altitude input from the air data computer. Additional Features Hazard Avoidance Display system is not receiving vertical speed input from the air data computer.
Annunciations & Alerts EIS The following annunciations are configured specifically for the PA-44-180 Seminole aircraft. See the PA-44-180 Seminole Pilot Operating Handbook (POH) for information regarding pilot responses.
Caution Annunciations Annunciation Window Text L FUEL QTY R FUEL QTY PITOT HEAT FAIL PITOT HEAT OFF GEAR SYS GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts CHECK GEAR Audio Alert Left fuel quantity in caution range Right fuel quantity in caution range Pitot heat failure Pitot heat selected OFF A failure of a gear system component has been detected Landing gear are not down and locked Hydraulic pump is running when it should not be running Double Chime Advisory Annunciati
Annunciations & Alerts Message Priority Flight Instruments VOICE ALERTS Description Flight Planning Procedures MFD Pop-Up Alert Hazard Avoidance Aural Message Reduced Required Obstacle Clearance Warning (ROC) “Warning; Obstacle, Obstacle” Imminent Obstacle Impact Warning (IOI) “Warning; Obstacle, Obstacle” Reduced Required Terrain Clearance Caution (RTC) “Caution; Terrain, Terrain” Imminent Terrain Impact Caution (ITI) “Caution; Terrain, Terrain” Reduced Required Obstacle Clearance Caution
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Alert Type PFD/MFD TERRAIN-SVT Page Annunciation MFD Pop-Up Alert Imminent Obstacle Impact Caution (IOI) Aural Message “Caution; Obstacle, Obstacle” TERRAIN-SVT SYSTEM STATUS ANNUNCIATIONS TERRAIN-SVT Page Annunciation Aural Message TERRAIN TEST None None “Terrain System Test OK” None None TERRAIN DA
Annunciations & Alerts Alert Type MFD Pop-Up Alert “Pull Up” or Imminent Obstacle Impact Warning (IOI) or or “Terrain Ahead; Terrain Ahead” or “Caution, Terrain; Caution, Terrain” or “Caution, Obstacle; Caution, Obstacle” or “Obstacle Ahead; Obstacle Ahead” Appendix Reduced Required Obstacle Clearance Caution (ROC) or “Caution, Terrain; Caution, Terrain” or “Terrain Ahead; Terrain Ahead” Annun/Alerts Imminent Terrain Impact Caution (ITI) “Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up” or
Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Alert Type PFD/MFD TAWS-B Page Annunciation Imminent Obstacle Impact Caution (IOI) Abnormal Operation Annun/Alerts Appendix Aural Message or “Obstacle Ahead; Obstacle Ahead” or “Caution, Obstacle; Caution, Obstacle” Premature Descent Alert Caution (PDA) Altitude Callout “500” “Too Low, Terrain” None None “Five-Hundred” Excessive Descent Rate Caution (
Annunciations & Alerts No GPS position Aural Message NO GPS POSITION “TAWS Not Available” None “TAWS Not Available” None “TAWS Available” Sufficient GPS signal received after loss None Nav/Com/ XPDR/Audio Excessively degraded GPS signal, Out of database coverage area EIS TAWS-B Page Annunciation Flight Instruments PFD/MFD Alert Annunciation Alert Type GPS Nav GDL 69/69A DATA LINK RECEIVER MESSAGES Message Location Description CHECK ANTENNA XM Information Page (MFD) Data Link Receiver
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts MFD & PFD MESSAGE ADVISORIES Message DATA LOST – Pilot stored data was lost. Recheck settings. XTALK ERROR – A flight display crosstalk error has occurred. PFD1 SERVICE – PFD1 needs service. Return unit for repair. MFD1 SERVICE – MFD1 needs service. Return unit for repair.
Annunciations & Alerts Flight Instruments Comments The PFD1 configuration module backup memory has failed. The system should be serviced. The PFD1 voltage is low. The system should be serviced. The MFD voltage is low. The system should be serviced. EIS Nav/Com/ XPDR/Audio Message CNFG MODULE – PFD1 configuration module is inoperative. PFD1 VOLTAGE – PFD1 has low voltage. Reducing power usage MFD1 VOLTAGE – MFD1 has low voltage.
Message MFD1 DB ERR – MFD1 obstacle database missing. PFD1 DB ERR – PFD1 obstacle database missing. MFD1 DB ERR – MFD1 airport terrain database error exists. PFD1 DB ERR – PFD1 airport terrain database error exists. MFD1 DB ERR – MFD1 airport terrain database missing. PFD1 DB ERR – PFD1 airport terrain database missing. MFD1 DB ERR – MFD1 Safe Taxi database error exists. PFD1 DB ERR – PFD1 Safe Taxi database error exists. MFD1 DB ERR – MFD1 Chartview database error exists.
Annunciations & Alerts EIS Nav/Com/ XPDR/Audio GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/Alerts Appendix Comments The PFD and MFD have different navigation database versions or regions installed. Crossfill is off. Check the AUX-SYSTEM STATUS Page to determine versions or regions. Also, check the AUX-SYSTEM STATUS Page for a database synchronization function not completed. After synchronization is complete, power must be turned off, then on.
Message DB MISMATCH – Airport Terrain database mismatch. NAV DB UPDATED – Active navigation database updated. TERRAIN DISABLED – Terrain Awareness DB resolution too low. TERRAIN DSP – [PFD1 or MFD1] Terrain awareness display unavailable. Comments The PFD and MFD have different airport terrain databases installed. Check the AUX-SYSTEM STATUS Page to determine versions or regions. Also, check the AUX-SYSTEM STATUS Page for a database synchronization function not completed.
Annunciations & Alerts The GIA1 and/or GIA2 configuration settings do not match backup configuration memory. The system should be serviced. Flight Planning The GIA1 and/or GIA2 temperature is too low to operate correctly. Allow units to warm up to operating temperature. GPS Nav The GIA1 and/or GIA2 have an error in the audio configuration. The system should be serviced. Nav/Com/ XPDR/Audio Procedures The GIA1 and/or GIA2 temperature is too high. If problem persists, the system should be serviced.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Message MANIFEST – GFC software mismatch, communication halted. MANIFEST – COM1 software mismatch, communication halted. MANIFEST – COM2 software mismatch, communication halted. MANIFEST – NAV1 software mismatch, communication halted. MANIFEST – NAV2 software mismatch, communication halted.
Annunciations & Alerts Loss of GPS navigation due to GPS failure. Abort approach due to loss of GPS navigation. Vertical guidance generated by SBAS is unavailable, use LNAV only minimums. Displayed after passing the first waypoint of a true north approach when the nav angle is set to ‘AUTO’. Flight Planning Procedures A failure has been detected in the GPS1 and/ or GPS2 receiver. The receiver may still be available. The system should be serviced.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Message G/S1 SERVICE – G/S1 needs service. Return unit for repair. G/S2 SERVICE – G/S2 needs service. Return unit for repair. TRN AUD FAIL – Trn Awareness audio source unavailable. TERRAIN AUD CFG – Trn Awareness audio config error. Service req’d.
Annunciations & Alerts Hazard Avoidance Additional Features Abnormal Operation Annun/Alerts MANIFEST – GRS1 software mismatch, communication halted. Procedures GEO LIMITS – AHRS1 too far North/South, no magnetic compass. Flight Planning AHRS1 GPS – AHRS1 not receiving backup GPS information. AHRS1 GPS – AHRS1 operating exclusively in no-GPS mode. AHRS1 SERVICE – AHRS1 needs service. Return unit for repair. AHRS1 SRVC – AHRS1 Magneticfield model needs update. AHRS1 CONFIG – AHRS1 config error.
GMU 44 MESSAGE ADVISORIES Message HDG FAULT – AHRS1 magnetometer fault has occurred. MANIFEST – GMU1 software mismatch, communication halted. Flight Planning GDL69 FAIL – GDL 69 has failed. Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Message GDL69 CONFIG – GDL 69 config error. Config service req’d. MANIFEST – GDL software mismatch, communication halted. Comments GDL 69 configuration settings do not match those of backup configuration memory. The system should be serviced.
Annunciations & Alerts Comments The GDC 74A has incorrect software installed. The system should be serviced. EIS Message MANIFEST – GDC1 software mismatch, communication halted. Flight Instruments GDC 74A MESSAGE ADVISORIES Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/Alerts Appendix Comments Upon power-up, the system detects that a stored flight plan waypoint is locked. This occurs when an navigation database update eliminates an obsolete waypoint.
Message DB CHANGE – Database changed. Verify stored airways. Comments This occurs when a stored flight plan contains an airway that is no longer consistent with the navigation database. This alert is issued only after an navigation database update. Verify use of airways in stored flight plans and reload airways as needed. FPL TRUNC – Flight plan has been This occurs when a newly installed navigation truncated. database eliminates an obsolete approach or arrival used by a stored flight plan.
Annunciations & Alerts Additional Features Abnormal Operation Annun/Alerts Appendix Index 95 Hazard Avoidance Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole Procedures 190-01462-00 Rev. A Flight Planning VNV – Unavailable. Excessive crosstrack error. VNV – Unavailable. Parallel course selected. IAF waypoint for parallel offset has been passed. IAF waypoint for parallel offset has been passed.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Message TRAFFIC FAIL – Traffic device has failed. Comments The system is no longer receiving data from the traffic system. The traffic device should be serviced. FAILED PATH – A data path has A data path connected to the GDU, GSD 41, or failed. the GIA 63W has failed.
Annunciations & Alerts Flight Instruments FLIGHT PLAN IMPORT/EXPORT MESSAGES In some circumstances, some messages may appear in conjunction with others. Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/Alerts Appendix Index 97 Flight Planning Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole GPS Nav 190-01462-00 Rev. A Nav/Com/ XPDR/Audio Description A flight plan file stored on the SD card was successfully imported as a stored flight plan.
Flight Plan Import/Export Results ‘User waypoint database full. Not all loaded.’ ‘One or more user waypoints renamed.’ ‘Flight plan successfully exported.’ ‘Flight plan export failed.’ Description The flight plan file on the SD card contains user waypoints. The quantity of stored user waypoints has exceeded system capacity, therefore not all the user waypoints on the SD card have been imported. Any flight plan user waypoints that were not imported are locked in the flight plan.
Annunciations & Alerts EIS Nav/Com/ XPDR/Audio GPS Nav Flight Planning Procedures Hazard Avoidance Pilot Profile Import/Export Results Description ‘No pilot profile plan files found to Displayed if the SD card does not have one import.’ or more valid pilot profile filenames. ‘Overwrite existing profile?’ Displayed if the profile name matches the name of existing profile. ‘Profile name invalid. Enter a different Displayed if the profile name is invalid. profile name.’ ‘All available pilot profiles in use.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Annunciations & Alerts Blank Page 100 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Appendix Flight Instruments APPENDIX PFD SOFTKEY MAP EIS CAS Nav/Com/ XPDR/Audio CAS ↑ CAS ↓ GPS Nav Flight Planning Top Level PFD Softkeys Procedures WX LGND METAR Select the BACK or OFF Softkey to return to the top-level softkeys. TRFC-2 Hazard Avoidance TRFC-1 Additional Features Inset Map Softkeys Level 2 CAS ↓ OFF 190-01462-00 Rev.
Level 1 Level 2 Description DCLTR (3) Selects desired amount of map detail; cycles through declutter levels: DCLTR (No Declutter): All map features visible DCLTR-1: Declutters land data DCLTR-2: Declutters land and SUA data DCLTR-3: Removes everything except the active flight plan WX LGND Displays icon and age on the Inset Map for the selected weather products (optional) TRAFFIC Cycles through traffic display options: TRFC-1: Traffic displayed on inset map TRFC-2: Traffic Map Page is displayed in the ins
Appendix Flight Instruments DME SYN VIS ALT UNIT HSI FMT EIS Select the BACK Softkey to return to the top-level softkeys Nav/Com/ XPDR/Audio METERS GPS Nav 360 HSI BACK ARC HSI IN HPA Flight Planning Procedures PATHWAY SYN TERR HRZN HDG APTSIGNS Level 1 Level 2 Hazard Avoidance PFD Configuration Softkeys SYN VIS SYN TERR Appendix HRZN HDG Displays compass heading along the Zero-Pitch line Annun/Alerts PATHWAY Displays second-level softkeys for additional PFD configurations Displa
Level 1 Level 2 Level 3 Description APTSIGNS Displays position markers for airports within approximately 15 nm of the current aircraft position. Airport identifiers are displayed when the airport is within approximately 9 nm.
Appendix Level 2 Level 3 METERS STD BARO Flight Planning Hazard Avoidance Select the BACK Softkey to return to the top-level softkeys. Additional Features Transponder Softkeys Level 3 Description STBY ALT Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 105 Index 190-01462-00 Rev.
Level 1 Level 2 Level 3 Description 0—7 Automatically enters the VFR code (1200 in the U.S.A. only) Displays transponder code selection softkeys 0-7 Use numbers to enter code BKSP Removes numbers entered, one at a time VFR CODE Nav/Com/ XPDR/Audio EIS Flight Instruments Appendix TMR/REF Activates/deactivates transmission of the aircraft’s three-dimensional position and aircraft heading for reception by ADS-B systems.
Appendix Level 2 ENGINE Abnormal Operation TERRAIN Additional Features TOPO Hazard Avoidance PROFILE Procedures TRAFFIC Flight Planning MAP Annun/Alerts Displays the default engine softkey level.
Level 1 Level 2 AIRWAYS Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Appendix Procedures NEXRAD Abnormal Operation Additional Features Hazard Avoidance XM LTNG Annun/Alerts METAR Index Appendix LEGEND BACK 108 Level 3 Level 4 Description Displays airways on the map; cycles through the following: AIRWAYS: No airways are displayed AIRWY ON: All airways are displayed AIRWY LO: Only low altitude airways are displayed AIRWY HI: Only high altitude airways are
Appendix Level 2 Level 3 Level 4 Description Appendix Index 109 Annun/Alerts Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole Abnormal Operation 190-01462-00 Rev. A Additional Features In some cases it may be necessary to obtain an unlock code from Garmin in order to make the database product functional. It may also be necessary to have the system configured by a Garmin authorized service facility in order to use some database features.
Error Message Description Canceled Database synchronization has been canceled by removing the bottom SD card in display being updated Card Full SD card does not contain sufficient memory Err Displayed for all other errors that may cause the synchronization process to be halted Timeout System timed-out prior to the database transfer completing Updating Basemap, SafeTaxi, Airport Terrain, Obstacle, and Airport Directory Databases These databases may be copied to one Supplemental Data Card, then automatically
Appendix Flight Instruments Updating Terrain, FliteCharts, and ChartView Databases These databases must be copied to both Supplemental Data Cards: EIS 1) With system power OFF, remove the Supplemental Data Card from the bottom card slot of the MFD and PFD. 3) Insert the updated Supplemental Data Cards into the bottom card slot of the MFD and PFD. Nav/Com/ XPDR/Audio 2) Update the terrain and/or FliteCharts or ChartView databases on each of the Supplemental Data Cards.
Loading the Jeppesen Navigation Database as the Active Navigation Database The Jeppesen Navigation Database that is loaded to internal memory as the active database will be used by the system.
Appendix Flight Instruments 5) After the update completes, the display starts in normal mode. 6) Turn the system OFF and remove the SD card from the top card slot. 7) Repeat steps 1 through 6 for the other display (PFD or MFD). 10) Turn the small FMS Knob to select the System Status Page. NOTE: After the navigation database is loaded or copied, the top SD card may be removed.
Appendix Flight Instruments 5) After the navigation database files are copied to the bottom SD card, press any key to verify, as instructed. EIS 6) After database verification is complete, press any key to continue as instructed on the display. Nav/Com/ XPDR/Audio 7) Press the NO Softkey. The display now starts in normal mode. Since the database effective date is not yet valid, it should not be loaded as the active database. The display now starts in normal mode.
Appendix EIS At startup, the system compares this version of the MV DB with that presently being used by the AHRS (GRS). If the system determines the MV DB needs to be updated, a prompt is displayed on the Navigation Map Page, as shown in the following figure.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Appendix Blank Page 116 Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole 190-01462-00 Rev.
Index Horizon heading 57 Abnormal Operation I Inhibit 54, 56 Inhibit TAWS 56 Inhibit Terrain 54 Insertion Point Indicator 31 Inset Map 101, 102 IOI 77, 78, 79, 80 Annun/Alerts Appendix J Index 190-01462-00 Rev.
Index Appendix Annun/Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav Nav/Com/ XPDR/Audio EIS Flight Instruments Index M Map panning 46 Message advisories 82, 83, 86, 87, 90, 91, 92, 93 METAR 45 MKR/MUTE 12 Mode S 105 Mode selection softkeys 11 Multi Function Display (MFD) Softkeys 106 N NAV 11, 12 NAV1 1, 11 NAV2 1, 11 Navigation database 17, 19 NEXRAD 45, 102, 108 O OBS 2 Obstacles 85, 86, 87 P Standby Navigation Database 113 Store Flight Pl
Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062, U.S.A. p: 913.397.8200 f: 913.397.8282 Garmin AT, Inc. 2345 Turner Road SE Salem, OR 97302, U.S.A. p: 503.391.3411 f: 503.364.2138 Garmin (Europe) Ltd Liberty House, Bulls Copse Road Hounsdown Business Park Southampton, SO40 9RB, U.K. p: 44/0870.8501241 f: 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road Shijr, Taipei County, Taiwan p: 886/2.2642.9199 f: 886/2.2642.9099 www.garmin.com © 2013 Garmin Ltd.
