Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs
- Set Barometric Minimum Descent Altitude
- Displaying Wind Data
- Changing HSI Format
- Engine Indication System
- Nav/Com/Transponder/Audio Panel
- GFC 700 Automatic Flight Control System (Optional)
- GPS Navigation
- Flight Planning
- Trip Planning
- Create a New User Waypoint
- Delete a User Waypoint
- Create a New Flight Plan
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- WARNING Annunciation
- CAUTION Annunciation
- Annunciation Advisory Alerts
- Alert Message
- AFCS Alerts
- Terrain-SVS Alerts
- Voice Alerts
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347 Message Advisories
- GIA 63 Message Advisories
- GIA 63W Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GDC 74A Message Advisories
- GDL 69A Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Garmin G1000 Cockpit Reference Guide for the DA42-L360
190-01062-01 Rev. A
2
Flight Instruments
Flight
InstrumentsEIS
Nav/Com/
XPDR/AudioAFCSGPS Nav
Flight
PlanningProcedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
AlertsAppendixIndex
ENABLE/DISABLE OBS MODE WHILE NAVIGATING WITH GPS
1)
Press the OBS Softkey to select OBS Mode.
2)
Turn a CRS Knob to select the desired course to/from the waypoint. Press a
CRS Knob to synchronize the Selected Course with the bearing to the next
waypoint.
3)
Press the OBS Softkey again to disable OBS Mode.
GENERIC TIMER
1)
Press the TMR/REF Softkey, then turn the large FMS Knob to select the
time field (hh/mm/ss). Turn the FMS Knobs to set the desired time, then
press the ENT Key. The UP/DOWN field is now highlighted.
2)
Turn the small FMS Knob to display the UP/DOWN window. Turn the FMS
Knob to select ‘UP’ or ‘DOWN’, then press the ENT Key. ‘START?’ is now
highlighted.
3)
Press the ENT Key to START, STOP, or RESET the timer (if the timer is
counting DOWN, it starts counting UP after reaching zero). Press the CLR
Key or the TMR/REF Softkey to remove the window.
CONFIGURE VSPEED BUGS
1)
Press the TMR/REF Softkey.
2)
Turn the
large
FMS Knob to highlight the desired Vspeed.
3)
Use the small FMS Knob to change the Vspeed in 1-kt increments (when a
speed has been changed from a default value, an asterisk appears next to
the speed).
4)
Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF
field
5)
Turn the
small
FMS Knob clockwise to ON or counterclockwise to OFF.
6)
To remove the window, press the CLR Key or the TMR/REF Softkey.