Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Synchronizing the Altimeter Barometric Pressure Settings
- Synchronize CDI
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs Individually
- Turn Vspeed Bugs On or Off by Category
- Set Barometric/Radar Altimeter (Optional) Minimum Descent Altitude
- Displaying Wind Data
- Engine & Airframe Systems
- Nav/Com/Transponder/Audio Panel
- Automatic Flight Control System
- GPS Navigation
- Flight Planning
- Weight Planning
- Trip Planning
- Create a User Waypoint Defined by Latitude & Longitude
- Create a User Waypoint Defined by Radials from Other Waypoints
- Create a User Waypoint Defined by a Radial & Distance from Another Waypoint
- Delete a User Waypoint
- Create a Flight Plan
- Import a Flight Plan from an SD Card
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Export a Flight Plan to an SD Card
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- CAS Messages
- Comparator Annunciations
- Reversionary Sensor Annunciations
- TAWS-A Alerts
- TAWS-B Alerts
- TCAS II Alerts and Annunciations
- Other Prodigy® Aural Alerts
- Flight Plan Import/Export Messages
- Pilot Profile Import/Export Messages
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347D Message Advisories
- GIA 63W Message Advisories
- GSD 41 Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GSR 56 Message Advisories
- GDL 59 Message Advisories
- GDL 69A Message Advisories
- GWX 68 Alert Messages
- GDC 74B Message Advisories
- GMC 715 Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Cockpit Reference Guide for the Prodigy
®
Flight Deck 300
190-00761-02 Rev. A
62
Hazard Avoidance
Flight
InstrumentsEAS
Nav/Com/
XPDR/AudioAFCSGPS Nav
Flight
PlanningProcedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
AlertsAppendixIndex
Adjusting Antenna Bearing
Move the
Joystick
right or left to adjust the azimuth position of the antenna right
or left. Monitor the displayed bearing value in the BEARING field.
When scanning horizontally, a Bearing Line may be displayed to aid in positioning
the antenna for the vertical scan. If the Bearing Line is not displayed, perform the fol-
lowing steps:
1)
Press the MENU Key
2)
Turn the large FMS Knob to select ‘Show Bearing Line’.
3)
Press the ENT Key.
Vertically Scan a Storm Cell
1) While in the Horizontal Scan view, move the Joystick to place the Bearing
Line on the desired storm cell, or other area, to be vertically scanned.
2)
Select the VERTICAL Softkey. A vertical “slice” of the selected area will
now be displayed.
3)
Move the Joystick right or left to move the scanned “slice” a few degrees
right or left.
4)
Turn the Joystick to adjust the range.
5)
To select a new area to be vertically scanned, select the HORIZON Softkey
to return to the Horizontal Scan view and repeat the previous steps.
Adjusting Gain
WARNING: Changing the gain in Weather Mode will cause precipitation
intensity to be displayed as a color not representative of the true intensity.
Remember to return the gain setting to ‘Calibrated’ for viewing the actual
intensity of precipitation.
1)
Select the GAIN Softkey to activate the cursor in the ‘GAIN’ field.
2)
Turn the small FMS Knob to adjust the gain for the desirable level. The
gain setting is visible in the gain field as a movable horizontal bar in
a flashing box. The line pointer is a reference depicting the calibrated
position.
3)
Press the FMS Knob to remove the cursor.
4)
Select the GAIN Softkey again to recalibrate the gain. ‘CALIBRATED’ will be
displayed in the ‘GAIN’ field.