Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Synchronizing the Altimeter Barometric Pressure Settings
- Synchronize CDI
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs Individually
- Turn Vspeed Bugs On or Off by Category
- Set Barometric/Radar Altimeter (Optional) Minimum Descent Altitude
- Displaying Wind Data
- Engine & Airframe Systems
- Nav/Com/Transponder/Audio Panel
- Automatic Flight Control System
- GPS Navigation
- Flight Planning
- Weight Planning
- Trip Planning
- Create a User Waypoint Defined by Latitude & Longitude
- Create a User Waypoint Defined by Radials from Other Waypoints
- Create a User Waypoint Defined by a Radial & Distance from Another Waypoint
- Delete a User Waypoint
- Create a Flight Plan
- Import a Flight Plan from an SD Card
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Export a Flight Plan to an SD Card
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- CAS Messages
- Comparator Annunciations
- Reversionary Sensor Annunciations
- TAWS-A Alerts
- TAWS-B Alerts
- TCAS II Alerts and Annunciations
- Other Prodigy® Aural Alerts
- Flight Plan Import/Export Messages
- Pilot Profile Import/Export Messages
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347D Message Advisories
- GIA 63W Message Advisories
- GSD 41 Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GSR 56 Message Advisories
- GDL 59 Message Advisories
- GDL 69A Message Advisories
- GWX 68 Alert Messages
- GDC 74B Message Advisories
- GMC 715 Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Cockpit Reference Guide for the Prodigy
®
Flight Deck 300
190-00761-02 Rev. A
Appendix
157
Flight
Instruments EAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
1)
With the system OFF, insert the SD card containing the new navigation
database version into the top card slot of the MFD.
2)
Verify that an SD card is inserted in the bottom slot of each PFD and the MFD.
3)
Turn the system ON. A prompt is displayed.
4)
Press the YES Softkey. The navigation database is copied to the SD card in
the bottom card slot of the MFD.
5)
After the navigation database files are copied to the bottom SD card, press
any key to continue, as instructed.
6)
Again, press any key to continue as instructed on the display.
7)
Press the NO Softkey. The display now starts in normal mode. Since the
database effective date is not yet valid, it should not be loaded as the
active database. The display now starts in normal mode. Do not remove
power while the display is starting.
8)
Press the ENT Key to acknowledge the startup screen.
9)
Turn the large FMS Knob to select the AUX Page group on the MFD.
10)
Turn the small FMS Knob to select the System Status Page.
11)
The new database is copied to the SD card in the bottom card slot of each
PFD. Progress can be monitored in the SYNC STATUS field. When copying
is finished, ‘Complete’ is displayed.
NOTE: During the synchronization process, version differences between
standby navigation databases will exist. This will result in the system
displaying a ‘DB Mismatch’ alert for the standby navigation databases. This
alert will remain until the next power cycle.
12)
Turn system power OFF.
13)
Remove the SD card from the top card slot of the MFD.
14)
Turn system power ON.
15)
Press the ENT Key to acknowledge the startup screen.
16)
Turn the large FMS Knob to select the AUX Page group on the MFD.
17)
Turn the small FMS Knob to select the System Status Page.
18)
Press the Display Database Selection Softkey to show standby navigation
database information for each display (MFD1 DB, PFD1 DB, PFD2 DB).
Verify the correct standby navigation database cycle information is shown
for each display.