Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Synchronizing the Altimeter Barometric Pressure Settings
- Synchronize CDI
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs Individually
- Turn Vspeed Bugs On or Off by Category
- Set Barometric/Radar Altimeter (Optional) Minimum Descent Altitude
- Displaying Wind Data
- Engine & Airframe Systems
- Nav/Com/Transponder/Audio Panel
- Automatic Flight Control System
- GPS Navigation
- Flight Planning
- Weight Planning
- Trip Planning
- Create a User Waypoint Defined by Latitude & Longitude
- Create a User Waypoint Defined by Radials from Other Waypoints
- Create a User Waypoint Defined by a Radial & Distance from Another Waypoint
- Delete a User Waypoint
- Create a Flight Plan
- Import a Flight Plan from an SD Card
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Export a Flight Plan to an SD Card
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- CAS Messages
- Comparator Annunciations
- Reversionary Sensor Annunciations
- TAWS-A Alerts
- TAWS-B Alerts
- TCAS II Alerts and Annunciations
- Other Prodigy® Aural Alerts
- Flight Plan Import/Export Messages
- Pilot Profile Import/Export Messages
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347D Message Advisories
- GIA 63W Message Advisories
- GSD 41 Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GSR 56 Message Advisories
- GDL 59 Message Advisories
- GDL 69A Message Advisories
- GWX 68 Alert Messages
- GDC 74B Message Advisories
- GMC 715 Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Cockpit Reference Guide for the Prodigy
®
Flight Deck 300
190-00761-02 Rev. A
Appendix
155
Flight
Instruments EAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
Error Message Description
Canceled Database synchronization has been canceled by removing the
bottom SD card in display being updated
Card Full SD card does not contain sufficient memory
Err Displayed for all other errors that may cause the synchronization
process to be halted
Timeout System timed-out prior to the database transfer completing
Loading Garmin Database Updates
1)
With system power OFF, remove the MFD database card from the bottom
card slot of the MFD.
2)
Update the Garmin databases on the MFD card.
3)
Insert the MFD database card into the bottom card slot of the MFD.
4)
Apply power to the system, check that the databases are initialized
and displayed on the power-up screen. When updating the terrain and
FliteCharts databases, a ‘Verifying’ message may be seen. If this message is
present, wait for the system to finish loading before proceeding to step 5.
5)
Acknowledge the Power-up Page agreement by pressing the ENT Key or
the right most softkey.
6)
Turn the large FMS Knob to select the AUX Page group on the MFD.
7)
Turn the small FMS Knob to select the System Status Page.
8)
Monitor the Sync Status in the Database Window. Wait for all databases to
complete synching, indicated by ‘Complete’ being displayed.
9)
Remove and reapply power to the system.
10)
Turn the large FMS Knob to select the AUX Page group on the MFD.
11)
Turn the small FMS Knob to select the System Status Page.
12)
Press the Display Database Selection Softkey to show database information
for each display (MFD1 DB, PFD1 DB, PFD2 DB). Verify the correct
database cycle information is shown for each database for each display.