Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Synchronizing the Altimeter Barometric Pressure Settings
- Synchronize CDI
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs Individually
- Turn Vspeed Bugs On or Off by Category
- Set Barometric/Radar Altimeter (Optional) Minimum Descent Altitude
- Displaying Wind Data
- Engine & Airframe Systems
- Nav/Com/Transponder/Audio Panel
- Automatic Flight Control System
- GPS Navigation
- Flight Planning
- Weight Planning
- Trip Planning
- Create a User Waypoint Defined by Latitude & Longitude
- Create a User Waypoint Defined by Radials from Other Waypoints
- Create a User Waypoint Defined by a Radial & Distance from Another Waypoint
- Delete a User Waypoint
- Create a Flight Plan
- Import a Flight Plan from an SD Card
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Export a Flight Plan to an SD Card
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- CAS Messages
- Comparator Annunciations
- Reversionary Sensor Annunciations
- TAWS-A Alerts
- TAWS-B Alerts
- TCAS II Alerts and Annunciations
- Other Prodigy® Aural Alerts
- Flight Plan Import/Export Messages
- Pilot Profile Import/Export Messages
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347D Message Advisories
- GIA 63W Message Advisories
- GSD 41 Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GSR 56 Message Advisories
- GDL 59 Message Advisories
- GDL 69A Message Advisories
- GWX 68 Alert Messages
- GDC 74B Message Advisories
- GMC 715 Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Cockpit Reference Guide for the Prodigy
®
Flight Deck 300
190-00761-02 Rev. A 127
Annunciations & Alerts
Flight
Instruments EAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
GIA 63W MESSAGE ADVISORIES (CONT.)
Message Comments
GIA1 SERVICE
– GIA1 needs service.
Return the unit for repair.
The GIA1 and/or GIA2 self-test has detected
a problem in the unit. The system should be
serviced.
GIA2 SERVICE
– GIA2 needs service.
Return the unit for repair.
HW MISMATCH
– GIA hardware
mismatch. GIA1 communication halted.
A GIA mismatch has been detected, where
only one is SBAS capable.
HW MISMATCH
– GIA hardware
mismatch. GIA2 communication halted.
MANIFEST
– GIA1 software
mismatch, communication halted.
The GIA1 and/or GIA 2 has incorrect software
installed. The system should be serviced.
MANIFEST
– GIA2 software
mismatch, communication halted.
MANIFEST
– GFC software
mismatch, communication halted.
Incorrect servo software is installed, or gain
settings are incorrect.
COM1 TEMP
– COM1 over temp.
Reducing transmitter power.
The system has detected an over temperature
condition in COM1 and/or COM2. The
transmitter is operating at reduced power. If the
problem persists, the system should be serviced.
COM2 TEMP
– COM2 over temp.
Reducing transmitter power.
COM1 SERVICE
– COM1 needs
service. Return unit for repair.
The system has detected a failure in COM1
and/or COM2. COM1 and/or COM2 may still
be usable. The system should be serviced when
possible.
COM2 SERVICE
– COM2 needs
service. Return unit for repair.
COM1 PTT
– COM1 push-to-talk key
is stuck.
The COM1 and/or COM2 external push-to-talk
switch is stuck in the enable (or “pressed”)
position. Press the PTT switch again to cycle its
operation. If the problem persists, the system
should be serviced.
COM2 PTT
– COM2 push-to-talk key
is stuck.
COM1 RMT XFR
– COM1 remote
transfer key is stuck.
The COM1 and/or COM2 transfer switch is
stuck in the enabled (or “pressed”) position.
Press the transfer switch again to cycle its
operation. If the problem persists, the system
should be serviced.
COM2 RMT XFR
– COM2 remote
transfer key is stuck.