Cockpit Reference Guide
Table Of Contents
- Flight Instruments
- Selecting the Altimeter Barometric Pressure Setting
- Selecting Standard Barometric Pressure
- Change Altimeter Barometric Pressure Setting Units
- Synchronizing the Altimeter Barometric Pressure Settings
- Synchronize CDI
- Change Navigation Sources
- Enable/Disable OBS Mode While Navigating with GPS
- Generic Timer
- Configure Vspeed Bugs Individually
- Turn Vspeed Bugs On or Off by Category
- Set Barometric/Radar Altimeter (Optional) Minimum Descent Altitude
- Displaying Wind Data
- Engine & Airframe Systems
- Nav/Com/Transponder/Audio Panel
- Automatic Flight Control System
- GPS Navigation
- Flight Planning
- Weight Planning
- Trip Planning
- Create a User Waypoint Defined by Latitude & Longitude
- Create a User Waypoint Defined by Radials from Other Waypoints
- Create a User Waypoint Defined by a Radial & Distance from Another Waypoint
- Delete a User Waypoint
- Create a Flight Plan
- Import a Flight Plan from an SD Card
- Insert a Waypoint in the Active Flight Plan
- Enter an Airway in a Flight Plan
- Invert An Active Flight Plan
- Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- Store a Flight Plan
- Edit a Stored Flight Plan
- Delete a Waypoint from the Flight Plan
- Invert and Activate a Stored Flight Plan
- Copy a Flight Plan
- Delete a Flight Plan
- Graphical Flight Plan Creation
- Export a Flight Plan to an SD Card
- Procedures
- Hazard Avoidance
- Additional Features
- Abnormal Operation
- Annunciations & Alerts
- CAS Messages
- Comparator Annunciations
- Reversionary Sensor Annunciations
- TAWS-A Alerts
- TAWS-B Alerts
- TCAS II Alerts and Annunciations
- Other Prodigy® Aural Alerts
- Flight Plan Import/Export Messages
- Pilot Profile Import/Export Messages
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347D Message Advisories
- GIA 63W Message Advisories
- GSD 41 Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GSR 56 Message Advisories
- GDL 59 Message Advisories
- GDL 69A Message Advisories
- GWX 68 Alert Messages
- GDC 74B Message Advisories
- GMC 715 Message Advisories
- Miscellaneous Message Advisories
- Appendix
- Index
Cockpit Reference Guide for the Prodigy
®
Flight Deck 300
190-00761-02 Rev. A 93
Additional Features
Flight
Instruments EAS
Nav/Com/
XPDR/Audio AFCS GPS Nav
Flight
Planning Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts Appendix Index
6)
Press the ENT Key.
7)
With ‘DELETE’ highlighted, press the ENT Key.
8)
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
9)
Press the FMS Knob to deactivate the cursor.
Importing a Profile from an SD Card
1)
Insert an SD card containing the pilot profile(s) into the top card slot on the
MFD.
2)
Turn the FMS Knob to select the AUX - System Setup Page.
3)
Select the IMPORT Softkey.
4)
The system displays the Pilot Profile Importing Window with ‘IMPORT’
highlighted. To change the selected profile to be imported from the SD card
(shown as ‘SELECT FILE’), turn the large FMS Knob to highlight the profile
file name, then turn the small FMS Knob to highlight a profile from the list,
and press the ENT Key.
5)
If desired, the profile name to be used after profile has been imported can
be changed by turning the FMS Knob to highlight the ‘PROFILE NAME’
field, then use the large and small FMS Knobs to enter the name, and press
the ENT Key. Imported profile names cannot begin with a blank space or
be named ‘DEFAULT’, ‘GARMIN DEFAULTS’ or ‘DEFAULT SETTINGS’.
6)
With ‘IMPORT’ highlighted, press the ENT Key.
7)
If the imported profile name is the same as an existing profile on the
system, the system displays an ‘Overwrite existing file? OK or CANCEL’
prompt. Press the ENT Key to replace profile on the system with the profile
imported from the SD card, or turn the FMS Knob to highlight ‘CANCEL’
and press the ENT Key to return to the Pilot Profile Importing Window.
8)
If successful, the system displays ‘Pilot profile import succeeded.’ in the
IMPORT RESULTS window below. With ‘OK’ highlighted, press the ENT or
CLR Keys or press the FMS Knob to return to the AUX - System Setup Page.
The imported profile becomes the active profile.