G1000 ® Integrated Flight Deck Cockpit Reference Guide for the Piper PA-46 Meridian System Software 0720.
Flight Instruments EICAS Nav/Com/Transponder/Audio Panel Automatic Flight Control System GPS Navigation Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annunciations & Alerts Appendix INDEx
Copyright © 2007, 2009 Garmin Ltd. or its subsidiaries. All rights reserved. This manual reflects the operation of System Software version 0720.05 or later for the Piper PA-46 Meridian. Some differences in operation may be observed when comparing the information in this manual to earlier or later software versions. Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel: 913/397.8200 Fax: 913/397.8282 Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Warnings, Cautions & Notes WARNING: Navigation and terrain separation must NOT be predicated upon the use of the terrain avoidance feature. The terrain avoidance feature is NOT intended to be used as a primary reference for terrain avoidance and does not relieve the pilot from the responsibility of being aware of surroundings during flight. The terrain avoidance feature is only to be used as an aid for terrain avoidance. Terrain data is obtained from third party sources.
Warnings, Cautions & Notes Warning: NEXRAD weather data is to be used for long-range planning purposes only. Due to inherent delays in data transmission and the relative age of the data, NEXRAD weather data should not be used for short-range weather avoidance. WARNING: The Garmin G1000, as installed in the Piper PA-46 Meridian aircraft, has a very high degree of functional integrity.
Warnings, Cautions & Notes WARNING: Lamp(s) inside this product may contain mercury (HG) and must be recycled or disposed of according to local, state, or federal laws. For more information, refer to our website at www.garmin.com/aboutGarmin/ environment/disposal.jsp. WARNING: Because of anomalies in the earth’s magnetic field, operating the G1000 within the following areas could result in loss of reliable attitude and heading indications. North of 70° North latitude and south of 70° South latitude.
Warnings, Cautions & Notes NOTE: This product, its packaging, and its components contain chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. This notice is being provided in accordance with California’s Proposition 65. If you have any questions or would like additional information, please refer to our web site at www.garmin.com/prop65.
Warnings, Cautions & Notes Blank Page Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Record of Revisions Part Number 190-00764-00 Rev A Change Summary Initial release 190-00764-01 Added Synthetic Vision System and GDU 9.05 Revision Date of Revision Affected Pages A January, 2009 All 190-00764-01 Rev.
Record of Revisions Blank Page RR-2 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Table of Contents Flight Instruments. ............................................................................................................... 1 Selecting the Altimeter Barometric Pressure Setting....................................................... 1 Selecting Standard Barometric Pressure (29.92 in Hg)..................................................... 1 Change Altimeter Barometric Pressure Setting Units.......................................................
Table of Contents Enter an Airway in a Flight Plan........................................................................................... 28 Invert An Active Flight Plan................................................................................................... 29 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan...................... 29 Store a Flight Plan...................................................................................................................
Table of Contents Annunciations & Alerts................................................................................................... 59 CAS Messages........................................................................................................................... 59 Comparator Annunciations.................................................................................................... 62 Reversionary Sensor Annunciations.....................................................................
Table of Contents Blank Page iv Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Flight Instruments Flight Instruments Flight Instruments Selecting the Altimeter Barometric Pressure Setting EICAS Turn the BARO Knob to select the desired setting. Nav/Com/ XPDR/Audio Selecting Standard Barometric Pressure (29.92 in Hg) 1) Select the PFD Softkey to display the second-level softkeys. AFCS 2) Select the STD BARO Softkey. Change Altimeter Barometric Pressure Setting Units GPS Nav 1) Select the PFD Softkey to display the second-level softkeys. 2) Select the ALT UNIT Softkey.
Change Navigation Sources 1) Select the CDI Softkey to change from GPS to VOR1 or LOC1. This places the light blue tuning box over the NAV1 standby frequency in the upper left corner of the PFD. EICAS Flight Instruments Flight Instruments 3) Select the CDI Softkey a third time to return to GPS. Enable/Disable OBS Mode While Navigating with GPS 1) Select the OBS Softkey to select OBS Mode.
Flight Instruments Flight Instruments 4) Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF field 5) Turn the small FMS Knob clockwise to ON or counterclockwise to OFF. EICAS 6) To remove the window, press the CLR Key or the TMR/REF Softkey. Turn ALL Vspeed Bugs On or Off Nav/Com/ XPDR/Audio 1) Select the TMR/REF Softkey. 2) Press the MENU Key. AFCS 3) Turn the FMS Knob to highlight the desired option. 4) Press the ENT Key. Select the TMR/REF Softkey to remove the window.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Flight Instruments Blank Page 4 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
EICAS 1 Flight Instruments Engine Indication & Crew Alerting System 1 EICAS 8 Nav/Com/ XPDR/Audio 2 2 9 GPS Nav 10 AFCS 3 3 4 4 5 12 5 Procedures 6 Flight Planning 11 6 13 8 14 9 15 10 Hazard Avoidance 7 13 Abnormal Operation 14 15 EIS Display (Reversionary Mode) Torque 6 Oil Temperature 11 Fuel Flow 2 7 CAS Display 12 Fuel Temperature 3 Interturbine Temperature Propeller Speed 8 13 4 Generator Speed 9 Cabin Pressure Altitude and Change Rate Differential P
Crew Alerting System (CAS) NOTE: Refer to the Annunciations and Alerts section for specific CAS messages. NOTE: Refer to the Pilot’s Operating Handbook (POH) for emergency procedures.
EICAS Flight Instruments EICAS Nav/Com/ XPDR/Audio When a new yellow caution message appears on the CAS display, it appears as black text on a yellow background. Pressing the Master Caution Indicator acknowledges all unacknowledged yellow messages, extinguishing the master caution light. The caution message is displayed as yellow text on black after it is acknowledged. Messages are displayed until the issue is corrected.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments EICAS Blank Page 8 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Nav/Com/XPDR/Audio Panel Flight Instruments Nav/Com/Transponder/Audio Panel Enter a Transponder Code EICAS 1) Select the XPDR Softkey to display the transponder mode selection softkeys. GPS Nav Selecting a COM Radio Flight Planning Transmit/Receive Procedures Press the COM1 MIC, COM2 MIC, or COM3 MIC Key (optional COM, if installed) on the audio panel. Receive Only Press the COM1, COM2, or COM3 Key (optional COM, if installed) on the audio panel.
NAV/COM Tuning 1) Press the small tuning knob to select the desired radio for tuning. A light blue box highlights the radio frequency to be tuned. EICAS Flight Instruments Nav/Com/XPDR/Audio Panel 3) Press the Frequency Transfer Key to place the frequency into the active frequency field. Digital Clearance Recorder and Player GPS Nav AFCS Nav/Com/ XPDR/Audio 2) Turn the respective tuning knobs to enter the desired frequency into the standby frequency field.
Nav/Com/XPDR/Audio Panel Press the PILOT and/or COPLT Key on either audio panel to select those isolated from hearing the Nav/Com radios and music.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Nav/Com/XPDR/Audio Panel Blank Page 12 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
AFCS Note: If the attitude information required for the default flight director modes becomes invalid or unavailable, the autopilot automatically disengages.
Vertical Modes Vertical Mode Pitch Hold Selected Altitude Armed Altitude Hold Vertical Speed VNAV VNAV Target Altitude Armed Abnormal Operation Glidepath Glideslope Go Around Control Annunciation Holds the current aircraft pitch attitude; may be used to climb/descend to the (default) Selected Altitude AFCS armed to capture the altitude displayed in the Selected Altitude * window Holds the current Altitude Reference ALT Key Maintains the current aircraft vertical speed; may be used to climb/descend VS K
AFCS Lateral Mode Heading Select Captures and tracks Selected Heading HDG GPS Captures and tracks selected navigation source (GPS, VOR, LOC) NAV Key VOR Flight Planning LOC BC Key BC Hazard Avoidance Captures and tracks a localizer signal for backcourse approaches Procedures GPS Captures and tracks selected navigation APR Key source (GPS, VOR, LOC) Additional Features VAPP Abnormal Operation LOC Disengages autopilot and commands a constant pitch angle and wings level GA Switch Annun/ Aler
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments AFCS Blank Page 16 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
GPS Navigation Flight Instruments GPS Navigation Direct-to Navigation EICAS Direct-to Navigation using the MFD ) Key. Nav/Com/ XPDR/Audio 1) With the MFD selected on the controller, press the Direct-to ( 2) Enter the waypoint identifier. 5) Turn the large FMS Knob to place the cursor over the ‘VNV’ altitude field. 6) Enter the desired altitude. Flight Planning 7) Press the ENT Key. If the waypoint entered is an airport, the option to select MSL or AGL is now displayed.
GPS Navigation Flight Instruments 7) Turn the small FMS Knob to enter the desired altitude. EICAS 8) Press the ENT Key. If the waypoint entered is an airport, the option to select MSL or AGL is now displayed. If the waypoint is not an airport, proceed to step 10. 9) Turn the small FMS Knob to select ‘MSL’ or ‘AGL’. Nav/Com/ XPDR/Audio 10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field.
GPS Navigation Flight Instruments Stop Navigating a Flight Plan 1) Press the FPL Key to display the Active Flight Plan Page. 2) Press the MENU Key to display the Page Menu Window. AFCS GPS Nav The navigation database only contains altitudes for procedures that call for “Cross at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the database. In this case the altitude may be entered manually.
Altitudes associated with approach procedures are “auto-designated”. This means the system will automatically use the altitudes loaded with the approach for giving vertical flight path guidance outside the FAF. Note these altitudes are displayed as small light blue text. Altitudes associated with arrival procedures are “manually-designated”. This means the system will not use the altitudes loaded with the arrival for giving vertical flight path guidance until designated to do so by the pilot.
GPS Navigation Flight Instruments White Text Altitude has been entered by the pilot. Altitude is designated for use in giving vertical flight path guidance. Altitude does not match the published altitude in navigation database or no published altitude exists. The system cannot use this altitude in determining vertical flight path guidance. Small Text Altitude is not designated to be used in determining vertical flight path guidance.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments GPS Navigation Blank Page 22 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Flight Planning Flight Instruments Flight Planning Weight & Fuel Planning EICAS All procedures apply to the MFD unless otherwise stated. Entering Weight Parameters Procedures Hazard Avoidance Additional Features 3) Select the FOB SYNC Softkey to enter the fuel on board quantity as read from the aircraft fuel quantity sensors. Abnormal Operation Manually enter the desired fuel quantity. Flight Planning 2) Turn the large FMS Knob to place the cursor in the ‘Fuel On Board’ field.
Flight Planning Flight Instruments 4) For Direct-to planning: a) Select the WPTS Softkey and verify that the starting waypoint field indicates ‘P.POS’ (present position). EICAS b) If necessary, press the MENU Key and select ‘Set WPT to Present Position’ to display ‘P.POS’. Nav/Com/ XPDR/Audio c) Press the ENT Key and the flashing cursor moves to the ending waypoint field.
Flight Planning 9) The flashing cursor moves to the calibrated airspeed field. Enter a calibrated airspeed. Press the ENT Key when finished. Nav/Com/ XPDR/Audio 8) The flashing cursor moves to the fuel onboard field. Modify the fuel onboard. Press the ENT Key when finished. In ‘AUTOMATIC’ mode, fuel onboard is provided by the entry made on the Weight Planning Page. EICAS 7) Enter the fuel flow. Press the ENT Key when finished. Note that in ‘automatic’ page mode, fuel flow is provided by the system.
Flight Planning Flight Instruments a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list is displayed. EICAS b) Turn the small FMS Knob to the right to display the ‘RECENT’ waypoints. c) Turn the large FMS Knob to select the desired waypoint. Nav/Com/ XPDR/Audio d) Press the ENT Key. 7) After pressing the ENT Key, the cursor is displayed in the ‘RAD’ (radial) field. Enter the desired radial from the reference waypoint. AFCS 8) Press the ENT Key. 10) Press the ENT Key.
Flight Planning Flight Instruments Using the MFD 1) Press the FPL Key. 2) Turn the small FMS Knob to display the Flight Plan Catalog Page. 3) Select the NEW Softkey to display a blank flight plan for the first empty storage location. EICAS 4) Turn the small FMS Knob to display the Waypoint Information Window. Nav/Com/ XPDR/Audio 5) Enter the identifier of the departure waypoint. 6) Press the ENT Key. NOTE: If a flight plan is active, an additional flight plan cannot be entered using the PFD.
Flight Instruments Flight Planning Insert a Waypoint in the Active Flight Plan 1) Press the FPL Key to display the active flight plan. EICAS 2) If necessary, press the FMS Knob to activate the cursor. 3) Turn the large FMS Knob to highlight the desired flight plan waypoint. The new waypoint is inserted before the highlighted waypoint. Nav/Com/ XPDR/Audio 4) Turn the small FMS Knob. The Waypoint Information Window is now displayed.
Flight Planning GPS Nav Invert An Active Flight Plan Flight Planning 1) Press the FPL Key to display the active flight plan. 2) Press the MENU Key to display the Page Menu. Procedures 3) Turn the large FMS Knob to highlight ‘Invert Flight Plan’. 4) Press the ENT Key. The original flight plan remains intact in its flight plan catalog storage location. Or, for a stored flight plan: Annun/ Alerts a) Press the MFD FPL Key and turn the small FMS Knob to select the Flight Plan Catalog Page.
Flight Planning 4) With ‘OK’ highlighted, press the ENT Key to remove the selected procedure or airway. Store a Flight Plan 1) After creating a flight plan on either the PFD or MFD, it may be saved by pressing the MENU Key. Nav/Com/ XPDR/Audio EICAS Flight Instruments 3) Press the CLR Key to display a confirmation window. 2) Turn the large FMS Knob to highlight ‘Store Flight Plan’ and press the ENT Key. AFCS 3) With ‘OK’ highlighted, press the ENT Key to store the flight plan.
Flight Planning 4) With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel the delete request, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key. Flight Instruments 5) Once all changes have been made, press the FMS Knob to remove the cursor. EICAS Nav/Com/ XPDR/Audio Invert and Activate a Stored Flight Plan 1) Press the FPL Key for the MFD. AFCS 2) Turn the small FMS Knob to select the Flight Plan Catalog Page. 3) Press the FMS Knob to activate the cursor.
Flight Planning 6) With ‘OK’ highlighted, press the ENT Key to delete the flight plan. To cancel, turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key. Graphical Flight Plan Creation Nav/Com/ XPDR/Audio EICAS Flight Instruments 5) Select the DELETE Softkey. A ‘Delete flight plan #?’ confirmation window is displayed. 1) Press the FPL Key to display the Active Flight Plan Page on the MFD. AFCS 2) Press the Joystick to activate the map pointer.
Procedures Flight Instruments Procedures Load and Activate a Departure Procedure EICAS 1) Press the PROC Key. 3) Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a list of available departures. 5) Press the ENT Key. A list of runways may be displayed for the departure. If so, turn either FMS Knob to select the desired runway. Flight Planning 7) Turn the large FMS Knob to highlight the desired transition. GPS Nav 6) Press the ENT Key.
Procedures Flight Instruments 4) Turn the large FMS Knob to highlight the desired arrival. 5) Press the ENT Key. A list of transitions is displayed for the selected arrival. 6) Turn either FMS Knob to select the desired transition. EICAS 7) Press the ENT Key. A list of runways may be displayed for the selected arrival. Nav/Com/ XPDR/Audio 8) Turn the large FMS Knob to highlight the desired runway. 9) Press the ENT Key. 10) With ‘LOAD?’ highlighted, press the ENT Key.
Procedures Flight Instruments the approach and will provide navigation guidance relative to the final approach course. EICAS 7) Press the ENT Key. ‘LOAD? or ACTIVATE?’ is now displayed with ‘LOAD?’ highlighted. 8) Turn the large FMS Knob to select either ‘LOAD?’ or ‘ACTIVATE?’. Selecting ‘LOAD?’ enters the selected approach procedure into the active flight plan, but is not currently active.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Procedures Blank Page 36 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Hazard Avoidance Flight Instruments Hazard Avoidance Customizing the Hazard Displays on the Navigation Map EICAS 3) Press the small FMS Knob to return to the Navigation Map Page. GPS Nav STORMSCOPE® (Optional) Hazard Avoidance 1) Select the MAP Softkey. Additional Features 2) Select the STRMSCP Softkey. Select the STRMSCP Softkey again to remove Stormscope Lightning Data from the Navigation Map Page.
Hazard Avoidance Flight Instruments 3) Turn the small FMS Knob to display the ‘Cell/Strike’ window. 4) Turn either FMS Knob to select ‘Cell’ or ‘Strike’. Press the ENT Key. EICAS 5) Push the FMS Knob to return to the Navigation Map Page. Clear Stormscope Lightning Data from the Navigation Map Page Nav/Com/ XPDR/Audio 1) Press the MENU Key (with the Navigation Map Page displayed). 2) Turn either FMS Knob to highlight the ‘Clear Stormscope® Lightning’ field and press the ENT Key.
Hazard Avoidance Nav/Com/ XPDR/Audio Displaying XM Weather on the Navigation Map Page EICAS WARNING: Use of XM weather for hazardous weather penetration is not recommended. Weather information provided by XM Radio Service is approved only for weather avoidance, not penetration. Flight Instruments XM Weather (Optional) 1) Select the MAP Softkey. AFCS 2) Select the NEXRAD or XM LTNG Softkey to display the desired weather.
Hazard Avoidance Flight Instruments information but allows the user to press the ENT Key and select that Airport’s Information Page to display the text of the report. Pressing the ENT Key when panning over a TFR displays TFR specific information.
Hazard Avoidance NOTE: Traffic Information Service (TIS) is only available when the aircraft is within the service volume of a TIS capable terminal radar site. Displaying Traffic on the Traffic Map Page Nav/Com/ XPDR/Audio NOTE: If the G1000 is configured to use an optional Traffic Advisory System (TAS), TIS is not available for use. EICAS Flight Instruments Traffic Information Service (TIS) AFCS 1) Turn the large FMS Knob to select the Map Page Group.
Hazard Avoidance Flight Instruments Displaying Traffic on the Traffic Map Page 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the second rectangular page icon. EICAS 3) Select the NORMAL Softkey to begin displaying traffic. ‘OPERATING’ is displayed in the Traffic Mode field. AFCS Nav/Com/ XPDR/Audio 4) Select the ALT MODE Softkey to change the altitude volume.
Hazard Avoidance Flight Instruments 3) Press the ENT Key. During the test ‘TAWS TEST’ is displayed in the center of the TAWS-B Page. When all is in working order, “TAWS System Test, OK” is heard. EICAS Display Terrain on the TAWS-B Page Nav/Com/ XPDR/Audio 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the TAWS-B Page. AFCS 3) If desired, select the VIEW Softkey to access the ARC and 360 softkeys.
Hazard Avoidance Nav/Com/ XPDR/Audio EICAS Flight Instruments Inhibit TAWS While the TAWS-B Page is displayed, select the INHIBIT Softkey. Or: 1) Press the MENU Key. 2) Turn the small FMS Knob to select ‘Inhibit TAWS’. 3) Press the ENT Key. Airborne Color Weather Radar Procedures Flight Planning GPS Nav AFCS Enable TAWS While the TAWS-B Page is displayed, select the INHIBIT Softkey. Or: 1) While the TAWS-B Page is displayed, press the MENU Key.
Hazard Avoidance Flight Instruments Or: EICAS If the aircraft is already airborne, select the WEATHER or GROUND Softkey. The one-minute warm-up period will be initiated, after which the radar will begin transmitting. The horizontal scan is initially displayed. 5) Turn the Joystick to select the desired range. Nav/Com/ XPDR/Audio 6) If desired, select the VERTICAL Softkey for vertical scanning.
Hazard Avoidance Flight Instruments 5) To select a new area to be vertically scanned, select the HORIZON Softkey to return to the Horizontal Scan view and repeat the previous steps. EICAS Adjusting Gain Nav/Com/ XPDR/Audio WARNING: Changing the gain in Weather Mode will cause precipitation intensity to be displayed as a color not representative of the true intensity. Remember to return the gain setting to ‘Calibrated’ for viewing the actual intensity of precipitation.
Hazard Avoidance Flight Instruments Antenna Stabilization 1) To activate or deactivate the antenna stabilization, select the MODE Softkey. EICAS 2) Select the STAB ON Softkey to activate antenna stabilization or select the STAB OFF Softkey to deactivate. The current stabilization condition is shown in the upper right of the weather radar display.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Hazard Avoidance Blank Page 48 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Additional Features Flight Instruments Additional Features Synthetic Vision GPS Nav Flight Planning Procedures Hazard Avoidance Pathways Flight Path Marker Horizon Heading Marks Terrain and Obstacle Alerting Three-dimensional Traffic Airport Signs Runway Display AFCS Additional Features Abnormal Operation • • • • • • • Nav/Com/ XPDR/Audio Synthetic Vision System (SVS) functionality is offered as an optional enhancement to the G1000 Integrated Flight Deck System.
Additional Features Flight Instruments 3) If not already enabled, press the SYN TERR Softkey. 4) Press the PATHWAY Softkey. EICAS 5) Press the BACK Softkey to return to the previous page. Displaying Heading on the Horizon Nav/Com/ XPDR/Audio 1) Press the PFD Softkey. 2) Press the SYN VIS Softkey. 3) If not already enabled, press the SYN TERR Softkey. AFCS 4) Press the HRZN HDG Softkey. 5) Press the BACK Softkey to return to the previous page.
Additional Features Procedures Hazard Avoidance Additional Features 1) Select the SHW CHRT Softkey when displayed. Or: Move the map pointer to point to a desired point on the map and select the SHW CHRT Softkey. Appendix 3) Select the GO BACK Softkey to return to the previous page. Annun/ Alerts 2) Select the DP, STAR, APR, WX, and NOTAM softkeys to access charts for departures, arrivals, approaches, weather and NOTAMs Note that NOTAMS are only available with ChartView.
Additional Features Flight Instruments View Charts from the Active Flight Plan Page 1) While viewing the Active Flight Plan Page, press the FMS Knob to activate the cursor. EICAS 2) Turn the large FMS Knob to select the departure airport, destination airport, departure, arrival, or approach. Nav/Com/ XPDR/Audio 3) Select the SHW CHRT Softkey. The appropriate chart is displayed, if available for the item selected. 4) Select the GO BACK Softkey to return to the previous page.
Additional Features Selecting a Category Flight Planning Procedures Hazard Avoidance 2) Select the CH + Softkey to go up through the list in the Channel Box, or move down the list with the CH – Softkey. Or: GPS Nav 1) While on the XM Radio Page, select the CHNL Softkey. AFCS Select an Available Channel within the Selected Category Nav/Com/ XPDR/Audio The Category Box of the XM Radio Page displays the currently selected category of audio. 1) Select the CATGRY Softkey on the XM Radio Page.
Additional Features Flight Instruments Assigning Channel Presets GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Up to 15 channels from any category can be assigned a preset number. 1) On the XM Radio Page, with the desired channel active, select the PRESETS Softkey to access the first five preset channels (PS1 - PS5). 2) Select the MORE Softkey to access the next five channels (PS6 – PS10), and again to access the last five channels (PS11 – PS15).
Abnormal Operation Flight Instruments Abnormal Operation Reversionary Mode Abnormal Operation Annun/ Alerts If GPS position is lost, or becomes invalid, selected hazards being displayed on the Navigation Map Page are removed until GPS position is again established. Additional Features Hazard Displays with Loss of GPS Position Hazard Avoidance When a COM tuning failure is detected by the system, the emergency frequency (121.
Unusual Attitudes The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary functions are displayed in these situations.
Abnormal Operation GPS Nav Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’ superimposed in yellow over the ‘own aircraft’ symbol as shown in the following figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly above and to the right of the aircraft symbol on the CDI as shown in the following figure.
EICAS Flight Instruments Abnormal Operation Symbolic Aircraft (Map pages and Inset Map) Dead Reckoning Indications As a result of operating in DR Mode, all GPS-derived data is computed based upon an estimated position and is displayed as yellow text on the display to denote degraded navigation source information.
Annunciations & Alerts Flight Instruments Annunciations & Alerts CAS Messages EICAS Display Inhibits GROUND ESI TOPI AIR LOPI ESDI X X X Abnormal Operation X Additional Features X Appendix X Annun/ Alerts Index 190-00764-01 Rev.
Warning Messages Description FUEL QTY LOW GENERATOR FAIL GENERATOR OFF GENERATOR AMPS HYDR PUMP ON ITT OIL PRESSURE NG OVERSPEED OIL TEMPERATURE L/R PITOT HT FAIL PROP HEAT FAIL PROP SPEED SURF DE-ICE FAIL TORQUE VOLTS Fuel quantity is less than 100 lbs Generator has failed Generator is off Generator current is too high Hydraulic pump is on.
Annunciations & Alerts Description HYDR PUMP ON OXYGEN X Nav/Com/ XPDR/Audio X AFCS X X X X X X Flight Planning * Only affected side (L, R) displayed in CAS message; noted CAS messages display L/R as an example. Advisory Messages Abnormal Operation Annun/ Alerts X X X X Appendix Alternator is off Propeller is operating in Beta mode Door is ajar Emergency bleed is on Propeller is feathered Left or right fuel pump is on.
GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Annunciations & Alerts Comparator Annunciations Comparator Window Text ALT MISCOMP Condition Difference in altitude sensors is > 200 ft. If both airspeed sensors detect < 35 knots, this is inhibited. IAS MISCOMP If either airspeed sensor detects > 35 knots, and the difference in sensors is > 10 kts. If either airspeed sensor detects > 80 knots, and the difference in sensors is > 7 kts.
Annunciations & Alerts Alert Condition Annunciation Yaw servo providing sustained force in the indicated direction. Aircraft rudder retrim after substantial pitch and power changes required.
TAWS Alerts Alert Type PFD/MFD TAWS-B Page Annunciation MFD Pop-Up Alert Aural Message Excessive Descent Rate Warning (EDR) “Pull Up” Reduced Required Terrain Clearance Warning (RTC) “Terrain, Terrain; Pull Up, Pull Up” Imminent Terrain Impact Warning (ITI) Terrain Ahead, Pull Up; Terrain Ahead, Pull Up” Reduced Required Obstacle Clearance Warning (ROC) “Obstacle Ahead, Pull Up; Obstacle Ahead, Pull Up” Imminent Obstacle Impact Warning (IOI) “Obstacle, Obstacle; Pull Up, Pull Up” Reduced Requi
Annunciations & Alerts PFD/MFD TAWS-B Page Annunciation Flight Instruments TAWS System Status Annunciations Aural Message TAWS System Test Fail None “TAWS System Failure” TAWS Alerting is disabled None None No GPS position or excessively degraded GPS signal None “TAWS Not Available” “TAWS Available” will be heard when sufficient GPS signal is re-established.
MFD & PFD Message Advisories Message DATA LOST – Pilot stored data was lost. Recheck settings. XTALK ERROR – A flight display crosstalk error has occurred. PFD1 SERVICE – PFD1 needs service. Return unit for repair. PFD2 SERVICE – PFD2 needs service. Return unit for repair. MFD1 SERVICE – MFD1 needs service. Return unit for repair. MANIFEST – PFD1 software mismatch, communication halted. MANIFEST – PFD2 software mismatch, communication halted. MANIFEST – MFD1 software mismatch, communication halted.
Annunciations & Alerts Comments EICAS The PFD and/or MFD is overheating and is reducing power consumption by dimming the display. If problem persists, the G1000 system should be serviced. Nav/Com/ XPDR/Audio AFCS A key is stuck on the PFD and/or MFD bezel. Attempt to free the stuck key by pressing it several times. The G1000 system should be serviced if the problem persists. GPS Nav Flight Planning The PFD1 configuration module backup memory has failed. The G1000 system should be serviced.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Annunciations & Alerts Database Message Advisories (Cont.) Message MFD1 DB ERR – MFD1 basemap database error exists. PFD1 DB ERR – PFD1 basemap database error exists. PFD2 DB ERR – PFD2 basemap database error exists. MFD1 DB ERR – MFD1 terrain database error exists. PFD1 DB ERR – PFD1 terrain database error exists.
Annunciations & Alerts Comments The MFD and/or PFD detected a failure in the airport terrain database. Ensure that the data card is properly inserted. Replace data card. If problem persists, The G1000 system should be serviced. EICAS Nav/Com/ XPDR/Audio AFCS The airport terrain database is present on another LRU, but is missing on the specified LRU.
Database Message Advisories (Cont.) Message DB MISMATCH – Aviation database type mismatch. Xtalk is off. Comments The PFDs and MFD have different aviation database types installed (Americas, European, etc.). Crossfill is off. Install correct aviation database type in all displays. DB MISMATCH – Terrain database The PFDs and MFD have different terrain version mismatch. database versions installed. Install correct terrain database version in all displays.
Annunciations & Alerts Comments The audio panel has incorrect software installed. The G1000 system should be serviced. Nav/Com/ XPDR/Audio AFCS The audio panel self-test has detected a problem in the unit. Certain audio functions may still be available, and the audio panel may still be usable. The G1000 system should be serviced when possible. GPS Nav GIA 63W Message Advisories The GIA1 and/or GIA2 configuration settings do not match backup configuration memory. The G1000 system should be serviced.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Annunciations & Alerts GIA 63W Message Advisories (Cont.) Message HW MISMATCH – GIA hardware mismatch. GIA1 communication halted. HW MISMATCH – GIA hardware mismatch. GIA2 communication halted. MANIFEST – GIA1 software mismatch, communication halted. MANIFEST – GIA2 software mismatch, communication halted.
Annunciations & Alerts Abort approach due to loss of GPS navigation. Vertical guidance generated by WAAS is unavailable, use LNAV only minimums. Displayed after passing the first waypoint of a true north approach when the nav angle is set to ‘AUTO’. GPS Nav Flight Planning Abnormal Operation The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”) state. Press the transfer switch again to cycle its operation. If the problem persists, the G1000 system should be serviced.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Annunciations & Alerts GIA 63W Message Advisories (Cont.) Message G/S1 SERVICE – G/S1 needs service. Return unit for repair. G/S2 SERVICE – G/S2 needs service. Return unit for repair. Comments A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver may still be available.
Annunciations & Alerts Comments The #1 transponder should be serviced when possible. The #2 transponder should be serviced when possible. There is no communication with the #1 transponder. There is no communication with the #2 transponder. EICAS Nav/Com/ XPDR/Audio AFCS Message XPDR1 SRVC – XPDR1 needs service. Return unit for repair. XPDR2 SRVC – XPDR2 needs service. Return unit for repair. XPDR1 FAIL – XPDR1 is inoperative. XPDR2 FAIL – XPDR2 is inoperative.
GRS 77 Message Advisories (Cont.) Message Comments AHRS1 GPS – AHRS1 not receiving The #1 AHRS is not receiving backup GPS backup GPS information. information. The G1000 system should be serviced. AHRS2 GPS – AHRS2 not receiving The #2 AHRS is not receiving backup GPS backup GPS information. information. The G1000 system should be serviced. AHRS1 GPS – AHRS1 operating The #1 AHRS is operating exclusively in no-GPS exclusively in no-GPS mode. mode. The G1000 system should be serviced.
Annunciations & Alerts AFCS GPS Nav The GMU 44 has incorrect software installed. The G1000 system should be serviced. Flight Planning MANIFEST – GMU1 software mismatch, communication halted. MANIFEST – GMU2 software mismatch, communication halted. Nav/Com/ XPDR/Audio HDG FAULT – AHRS2 magnetometer fault has occurred. Comments A fault has occurred in the #1 GMU 44. Heading is flagged as invalid. The AHRS uses GPS for backup mode operation. The G1000 system should be serviced.
GWX 68 Alert Messages Message GWX CONFIG – GWX config error. Config service req’d. GWX FAIL – GWX is inoperative. GWX SERVICE – GWX needs service. Return unit for repair. MANIFEST – GWX software mismatch, communication halted. Comments GWX 68 configuration settings do not match those of the GDU configuration. The G1000 system should be serviced. The GDU is not recieving status packet from the GWX 68 or the GWX 68 is reporting a fault. The GWX 68 radar system should be serviced.
Annunciations & Alerts Flight Planning Comments Procedures Error in the configuration of the GMC 710. Hazard Avoidance A failure has been detected in the GMC 710. The GMC 710 is unavailable. The GMC 710 has incorrect software installed. The G1000 system should be serviced. A key is stuck on the GMC 710 bezel. Attempt to free the stuck key by pressing it several times. The G1000 system should be serviced if the problem persists. Additional Features Abnormal Operation MANIFEST – GMC software mismatch.
Miscellaneous Message Advisories Message FPL WPT LOCK – Flight plan waypoint is locked. Comments Upon power-up, the G1000 system detects that a stored flight plan waypoint is locked. This occurs when an aviation database update eliminates an obsolete waypoint. The flight plan cannot find the specified waypoint and flags this message. This can also occur with user waypoints in a flight plan that is deleted.
Annunciations & Alerts Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix Index 81 GPS Nav Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian AFCS 190-00764-01 Rev. A Nav/Com/ XPDR/Audio Comments This occurs when a newly installed aviation database eliminates an obsolete approach or arrival used by a stored flight plan. The obsolete procedure is removed from the flight plan. Update flight plan with current arrival or approach.
Miscellaneous Message Advisories (Cont.) Message PTK FAIL – Parallel track unavailable: bad geometry. PTK FAIL – Parallel track unavailable: invalid leg type. PTK FAIL – Parallel track unavailable: past IAF. UNABLE V WPT – Can’t reach current vertical waypoint. VNV – Unavailable. Unsupported leg type in flight plan. VNV – Unavailable. Excessive track angle error. VNV – Unavailable. Excessive crosstrack error. VNV – Unavailable. Parallel course selected.
Annunciations & Alerts GPS Nav Flight Planning Procedures SCHEDULER [#] – . AFCS SVS – SVS DISABLED: Terrain DB resolution too low. Nav/Com/ XPDR/Audio SVS – SVS DISABLED: Out of available terrain region. Comments A data path connected to the GDU or the GIA 63/W has failed. The GDU’s internal model cannot determine the exact magnetic variance for geographic locations near the magnetic poles. Displayed magnetic course angles may differ from the actual magnetic heading by more than 2°.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Annunciations & Alerts Blank Page 84 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Appendix Flight Instruments Appendix PFD Softkey Map EICAS Nav/Com/ XPDR/Audio AFCS GPS Nav Top Level PFD Softkeys Flight Planning TRFC-1 Procedures STRMSCP Hazard Avoidance Select the BACK or OFF Softkey to return to the top-level softkeys.
Appendix Cycles through traffic display options: TRFC-1: Traffic displayed on inset map TRFC-2: Traffic Map Page is displayed in the inset map window Displays topographical data (e.g.
Appendix Flight Instruments SYN VIS ALT UNIT EICAS Select the BACK Softkey to return to the top-level softkeys Nav/Com/ XPDR/Audio IN AFCS METERS HPA GPS Nav SYN TERR HRZN HDG APTSIGNS Flight Planning PATHWAY PFD Annun/ Alerts Displays compass heading along the Zero-Pitch line Displays position markers for airports within approximately 15 nm of the current aircraft position. Airport identifiers are displayed when the airport is within approximately 9 nm.
Appendix Flight Instruments WIND EICAS OPTN 1 OPTN 2 Nav/Com/ XPDR/Audio OPTN 3 Flight Planning GPS Nav AFCS OFF Select to display the DME information window BRG1 Cycles the Bearing 1 Information Window through NAV1 or GPS/ waypoint identifier and GPS-derived distance information. Cycles the Bearing 2 Information Window through NAV2 or GPS/ waypoint identifier and GPS-derived distance information.
Appendix Flight Instruments MSG EICAS Select the BACK Softkey to return to the top-level softkeys. Nav/Com/ XPDR/Audio MSG AFCS Select the BACK Softkey to return to the top-level softkeys.
Appendix 0—7 Manually selects Ground Mode, the transponder does not allow Mode A and Mode C replies, but it does permit acquisition squitter and replies to discretely addressed Mode S interrogations. Automatically enters the VFR code (1200 in the U.S.A.
Appendix CAS ↑ TRAFFIC Nav/Com/ XPDR/Audio MAP EICAS CAS ↓ Flight Instruments Scroll up (Displayed only when a sufficient number of items are displayed in the Crew Alerting System Display to warrant scrolling) Scroll down (Displayed only when a sufficient number of items are displayed in the Crew Alerting System Display to warrant scrolling) Enables second-level Navigation Map softkeys Displays traffic information on Navigation Map Displays topographical data (e.g.
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Appendix Blank Page 92 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Index D AFCS GPS Nav Flight Planning E Edit a flight plan 30 Engine display 5 Procedures F Appendix Gain 46 Generator Speed 5 Annun/ Alerts Cabin pressure altitude 5 CDI 1, 2, 9, 81 Cell 37, 38 Cell mode 38 Channel Presets 54 ChartView 50, 51 Clearance player 10 Clearance recorder 10 Abnormal Operation G Additional Features C Hazard Avoidance Barometric Altitude Minimums 3 Barometric pressure 88 Battery Voltage 5 Bearing line 45, 46 H Horizon heading 49 Horizontal scan 46 Garmin G1000 Cockp
GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Index I Inhibit 44 Inhibit TAWS 44 Inset Map 85, 86 Intercom isolation 11 Interturbine Temperature (ITT) 5 IOI 64 Flight Planning Procedures Hazard Avoidance Additional Features Abnormal Operation Annun/ Alerts Appendix P J Pathways 49 PIT 62 Propeller speed 5 Jeppesen 51 R L Reversionary Mode EICAS 5, 6 Reversionary mode 55 ROC 64 Lightning 37, 38, 86 M Index Oil, engine Pressure 5 Temperature 5 Overspeed Protection 14 Map panning
Index Flight Instruments Torque 5 Traffic 37, 41, 91 Traffic advisory 41 Traffic map page 41, 42 Transponder 9, 89, 90 EICAS Nav/Com/ XPDR/Audio V AFCS Vertical speed guidance 21 Vertical track 65 VNV 17, 56, 82 Vspeed 2 GPS Nav W Flight Planning WAAS 72 WATCH® 47 Weather Attenuated Color Highlight 47 Weather data link page 39 Weather radar 44 Wind data 88 Procedures X Hazard Avoidance XM lightning 86, 91 XM weather 39 Additional Features Abnormal Operation Annun/ Alerts Appendix Index 190-00
Index Appendix Annun/ Alerts Abnormal Operation Additional Features Hazard Avoidance Procedures Flight Planning GPS Nav AFCS Nav/Com/ XPDR/Audio EICAS Flight Instruments Index Blank Page Index-4 Garmin G1000 Cockpit Reference Guide for the Piper PA-46 Meridian 190-00764-01 Rev.
Garmin International, Inc. 1200 East 151st Street Olathe, KS 66062, U.S.A. p: 913.397.8200 f: 913.397.8282 Garmin AT, Inc. 2345 Turner Road SE Salem, OR 97302, U.S.A. p: 503.391.3411 f: 503.364.2138 Garmin (Europe) Ltd Liberty House, Bulls Copse Road Hounsdown Business Park Southampton, SO40 9RB, U.K. p: 44/0870.8501241 f: 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road Shijr, Taipei County, Taiwan p: 886/2.2642.9199 f: 886/2.2642.9099 www.garmin.com © 2007, 2009 Garmin Ltd.
