Pilot's Guide
Table Of Contents
- Section 1 System Overview
- Section 2 Flight Instruments
- Section 3 Engine Indication System (EIS)
- Section 4 Audio Panel and CNS
- Section 5 Flight Management
- 5.1 Introduction
- 5.2 Using Map Displays
- 5.3 Waypoints
- 5.4 Airspaces
- 5.5 Direct-to-Navigation
- 5.6 Flight Planning
- Flight Plan Creation
- Adding Waypoints to an Existing Flight Plan
- Adding Airways to a Flight Plan
- Adding Procedures to a Stored Flight Plan
- Flight Plan Storage
- Flight Plan Editing
- Along Track Offsets
- Parallel Track
- Activating a Flight Plan Leg
- Inverting a Flight Plan
- Flight Plan Views
- Closest Point of FPL
- User-Defined Holding Patterns
- 5.7 Vertical Navigation
- 5.8 Procedures
- 5.9 Trip Planning
- 5.10 RAIM Prediction
- 5.11 Navigating a Flight Plan
- 5.12 Abnormal Operation
- Section 6 Hazard Avoidance
- Section 7 Automatic Flight Control System
- Section 8 Additional Features
- 8.1 Synthetic Vision Technology (SVT) (Optional)
- 8.2 SafeTaxi
- 8.3 ChartView (Optional)
- 8.4 FliteCharts
- 8.5 Airport Directory
- 8.6 Satellite Telephone Services
- 8.7 SiriusXM Satellite Radio (Service Optional)
- 8.8 Scheduler
- 8.9 Electronic Checklists
- 8.10 Flight Data Logging
- 8.11 Auxiliary Video (Optional)
- 8.12 Abnormal Operation
- Appendices
- Index
190-00498-08 Rev. A
Garmin G1000 Pilot’s Guide for Cessna Nav III
61
FLIGHT INSTRUMENTS
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE
AFCS
ADDITIONAL
FEATURES
APPENDICES INDEX
When a bearing pointer is displayed, the associated information window is also displayed. The Bearing
Information Windows (Figure 2-18) are displayed at the lower sides of the HSI and give the following
information:
• Bearing source (NAV, GPS, ADF)
• Pointer icon (BRG1 = single line,BRG2 = double
line)
• Frequency (NAV, ADF)
• Station/waypoint identifier (NAV, GPS)
• GPS-derived great circle distance to bearing
source
When the NAV radio is tuned to an ILS frequency the bearing source and the bearing pointer is removed
from the HSI. When NAV1 or NAV2 is the selected bearing source, the frequency is replaced by the station
identifier when the station is within range. If GPS is the bearing source, the active waypoint identifier is
displayed instead of a frequency.
The bearing pointer is removed from the HSI and NO DATA is displayed in the information window if
the NAV radio is not receiving a VOR station or if GPS is the bearing source and an active waypoint is not
selected.
Selecting bearing display and changing sources:
1) Press the PFD Softkey.
2) Press a BRG Softkey to display the desired bearing pointer and information window with a NAV source.
3) Press the BRG Softkey again to change the bearing source to GPS.
4) To remove the bearing pointer and information window, press the BRG Softkey again.
DME INFORMATION WINDOW
The DME Information Window is displayed above the BRG1 Information Window on the 360˚ HSI and in
a box above and along side the Arc HSI. It shows the DME label, tuning mode (NAV1, NAV2, or HOLD),
frequency, and distance. When a signal is invalid, the distance is replaced by –.– – NM Refer to the Audio
Panel and CNS Section for information on tuning the DME.
NOTE: DME installation is optional.
Displaying the DME Information Window:
1) Press the PFD Softkey.
2) Press the DME Softkey to display the DME Information Window.
3) To remove the DME Information Window, press the DME Softkey again.