Pilot's Guide
Table Of Contents
- Section 1 System Overview
- Section 2 Flight Instruments
- Section 3 Engine Indication System (EIS)
- Section 4 Audio Panel and CNS
- Section 5 Flight Management
- 5.1 Introduction
- 5.2 Using Map Displays
- 5.3 Waypoints
- 5.4 Airspaces
- 5.5 Direct-to-Navigation
- 5.6 Flight Planning
- Flight Plan Creation
- Adding Waypoints to an Existing Flight Plan
- Adding Airways to a Flight Plan
- Adding Procedures to a Stored Flight Plan
- Flight Plan Storage
- Flight Plan Editing
- Along Track Offsets
- Parallel Track
- Activating a Flight Plan Leg
- Inverting a Flight Plan
- Flight Plan Views
- Closest Point of FPL
- User-Defined Holding Patterns
- 5.7 Vertical Navigation
- 5.8 Procedures
- 5.9 Trip Planning
- 5.10 RAIM Prediction
- 5.11 Navigating a Flight Plan
- 5.12 Abnormal Operation
- Section 6 Hazard Avoidance
- Section 7 Automatic Flight Control System
- Section 8 Additional Features
- 8.1 Synthetic Vision Technology (SVT) (Optional)
- 8.2 SafeTaxi
- 8.3 ChartView (Optional)
- 8.4 FliteCharts
- 8.5 Airport Directory
- 8.6 Satellite Telephone Services
- 8.7 SiriusXM Satellite Radio (Service Optional)
- 8.8 Scheduler
- 8.9 Electronic Checklists
- 8.10 Flight Data Logging
- 8.11 Auxiliary Video (Optional)
- 8.12 Abnormal Operation
- Appendices
- Index
190-00498-08 Rev. A
Garmin G1000 Pilot’s Guide for Cessna Nav III
SYSTEM
OVERVIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO PANEL
& CNS
FLIGHT
MANAGEMENT
HAZARD
AVOIDANCE
AFCS
ADDITIONAL
FEATURES
APPENDICESINDEX
602
APPENDIX A
GDC 74A MESSAGE ADVISORIES
Message Comments
ADC1 SERVICE
– ADC1 needs
service. Return unit for repair.
The #1 Air Data Computer should be serviced when possible.
MANIFEST
– GDC1 software
mismatch, communication halted.
The GDC 74A has incorrect software installed. The G1000 system should be serviced.
GTS 800 MESSAGE ADVISORIES
Message Comments
GTS CONFIG
– GTS config error.
Config service req’d.
The GTS and GDU have incompatible configurations. This alert is also set when the
GTS has an invalid mode S address configured or the mode S address does not match
both XPDR mode S addresses.
MANIFEST
– GTS software
mismatch, communication halted.
The GTS has incorrect software installed. The system should be serviced.
GDL 90 MESSAGE ADVISORIES
Message Comments
GDL90 CONFIG
– GDL 90 config
error. Config service req’d.
GDL 90 configuration settings do not match those of backup configuration memory.
The system should be serviced.
GDL90 FAIL
– GDL 90 has failed. A failure has been detected in the GDL 90. The receiver is unavailable. The system
should be serviced
MANIFEST
– GDL software
mismatch, communication halted.
The GDL 90 has incorrect software installed. The system should be serviced.
MISCELLANEOUS MESSAGE ADVISORIES
Message Comments
FPL WPT LOCK
– Flight plan
waypoint is locked.
Upon power-up, the system detects that a stored flight plan waypoint is locked. This
occurs when an navigation database update eliminates an obsolete waypoint. The
flight plan cannot find the specified waypoint and flags this message. This can also
occur with user waypoints in a flight plan that is deleted.
Remove the waypoint from the flight plan if it no longer exists in any database,
Or
update the waypoint name/identifier to reflect the new information.
FPL WPT MOVE
– Flight plan
waypoint moved.
The system has detected that a waypoint coordinate has changed due to a new navigation
database update. Verify that stored flight plans contain correct waypoint locations.
TIMER EXPIRD
– Timer has expired. The system notifies the pilot that the timer has expired.
DB CHANGE
– Database changed.
Verify user modified procedures.
This occurs when a stored flight plan contains procedures that have been manually
edited. This alert is issued only after an navigation database update. Verify that the
user-modified procedures in stored flight plans are correct and up to date.
DB CHANGE
– Database changed.
Verify stored airways.
This occurs when a stored flight plan contains an airway that is no longer consistent
with the navigation database. This alert is issued only after an navigation database
update. Verify use of airways in stored flight plans and reload airways as needed.