Cockpit Reference Guide
Table Of Contents
- Section 1: System Overview
- Section 2: Flight Instruments
- Section 3: Engine Indication System (EIS)
- Section 4: NAV/COM and Transponder
- Section 5: Audio Panel
- Section 6: Automatic Flight Control
- Section 7: Navigation
- 7.1 Navigation Map Page
- 7.2 Direct-to Navigation
- 7.3 Navigating an Example Flight Plan
- 7.4 Airport Information
- 7.5 Intersection Information
- 7.6 NDB Information
- 7.7 VOR Information
- 7.8 User Waypoint Information Page
- 7.9 Nearest Airports
- 7.10 Nearest Intersections
- 7.11 Nearest NDB
- 7.12 Nearest VOR
- 7.13 Nearest User Waypoint
- 7.14 Nearest Frequencies
- 7.15 Nearest Airspaces
- Section 8: Flight Planning
- 8.1 User Defined Waypoints
- 8.2 Viewing the Active Flight Plan
- 8.3 Activate a Stored Flight Plan
- 8.4 Activate a Flight Plan Leg
- 8.5 Stop Navigating a Flight Plan
- 8.6 Invert Active Flight Plan
- 8.7 Create a New Flight Plan
- 8.8 Enter an Airway in a Flight Plan
- 8.9 Load a Departure
- 8.10 Load an Arrival
- 8.11 Load an Approach
- 8.12 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- 8.13 Store a Flight Plan
- 8.14 Edit a Stored Flight Plan
- 8.15 Delete a Waypoint from the Flight Plan
- 8.16 Invert and Activate a Stored Flight Plan
- 8.17 Copy a Flight Plan
- 8.18 Delete a Flight Plan
- 8.19 Graphical Flight Plan Creation
- 8.20 Trip Planning
- Section 9: Procedures
- Section 10: Hazard Avoidance
- 10.1 Customizing the Hazard Displays on the Navigation Map
- 10.2 STORMSCOPE® (Optional)
- 10.3 XM Weather (Service Optional)
- 10.4 Traffic Systems
- 10.5 Terrain and Obstacle Proximity
- 10.6 Terrain Awareness & Warning System (TAWS) Display (Optional)
- Displaying Terrain on the TAWS Page
- Enable/Disable Aviation Data
- TAWS Inhibit
- Manual System Test
- Forward Looking Terrain Avoidance (FLTA)
- Premature Descent Alert (PDA)
- Excessive Descent Rate Alert (EDR)
- Negative Climb Rate After TakeoffAlert (NCR)
- “Five-Hundred” Aural Alert
- Displaying Terrain and Obstacles on the Navigation Map
- Pop-up Alerts
- TAWS Alerts Summary
- Alert Annunciations
- Section 11: Abnormal Operation
- Section 12: Annunciations & Alerts
- 12.1 Alert Level Definitions
- 12.2 NAV III Aircraft Alerts
- 12.3 CO Guardian Messages
- 12.4 AFCS Alerts
- 12.5 TAWS Alerts
- 12.6 Other G1000 Aural Alerts
- 12.7 G1000 System Annunciations
- 12.8 G1000 System Message Advisories
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347 Message Advisories
- GIA 63 Message Advisories
- GIA 63W Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GDL 69A Message Advisories
- GDC 74A Message Advisories
- Miscellaneous Message Advisories
- Index

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III
190-00384-08 Rev. A
2-12
SECTION 2
FLIGHT INSTRUMENTS
• OBS – Displayed when operating in OBS Mode.
• SUSP – Displayed when in OBS Mode indicating
GPS waypoint sequencing is suspended.
• DR – Navigating using Dead Reckoning due to an
error in the GPS solution.
Figure 2-29 GPS LOI, GPS SUSP, LOC1 and VOR2
Enable/disable OBS Mode while navigating
with GPS:
1)
Press the OBS Softkey to select OBS Mode.
2)
Turn the CRS Knob to select the desired course
to/from the waypoint.
3)
Press the OBS Softkey again to disable OBS
Mode.
NOTE: The OBS Softkey is only displayed when
navigating an active leg using GPS.
2.9 WIND DATA
When the window is selected for display, but wind
information is invalid or unavailable, the window shows
“NO WIND DATA”. Wind data can be displayed in three
different ways:
• Wind direction arrows with headwind and crosswind
components (Option 1)
• Wind direction arrow and speed (Option 2)
• Wind direction arrow with direction and speed
(Option 3)
Option 1 Option 2
Option 3 No Data
Figure 2-30 Wind Data Window
Displaying wind data:
1)
Press the PFD Softkey.
2)
Press the WIND Softkey to display wind data below
the Selected Heading.
3)
Press one of the OPTN softkeys to change how
wind data is displayed.
4)
To remove the Wind Data Window, press the OFF
Softkey.










