Cockpit Reference Guide
Table Of Contents
- Section 1: System Overview
- Section 2: Flight Instruments
- Section 3: Engine Indication System (EIS)
- Section 4: NAV/COM and Transponder
- Section 5: Audio Panel
- Section 6: Automatic Flight Control
- Section 7: Navigation
- 7.1 Navigation Map Page
- 7.2 Direct-to Navigation
- 7.3 Navigating an Example Flight Plan
- 7.4 Airport Information
- 7.5 Intersection Information
- 7.6 NDB Information
- 7.7 VOR Information
- 7.8 User Waypoint Information Page
- 7.9 Nearest Airports
- 7.10 Nearest Intersections
- 7.11 Nearest NDB
- 7.12 Nearest VOR
- 7.13 Nearest User Waypoint
- 7.14 Nearest Frequencies
- 7.15 Nearest Airspaces
- Section 8: Flight Planning
- 8.1 User Defined Waypoints
- 8.2 Viewing the Active Flight Plan
- 8.3 Activate a Stored Flight Plan
- 8.4 Activate a Flight Plan Leg
- 8.5 Stop Navigating a Flight Plan
- 8.6 Invert Active Flight Plan
- 8.7 Create a New Flight Plan
- 8.8 Enter an Airway in a Flight Plan
- 8.9 Load a Departure
- 8.10 Load an Arrival
- 8.11 Load an Approach
- 8.12 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- 8.13 Store a Flight Plan
- 8.14 Edit a Stored Flight Plan
- 8.15 Delete a Waypoint from the Flight Plan
- 8.16 Invert and Activate a Stored Flight Plan
- 8.17 Copy a Flight Plan
- 8.18 Delete a Flight Plan
- 8.19 Graphical Flight Plan Creation
- 8.20 Trip Planning
- Section 9: Procedures
- Section 10: Hazard Avoidance
- 10.1 Customizing the Hazard Displays on the Navigation Map
- 10.2 STORMSCOPE® (Optional)
- 10.3 XM Weather (Service Optional)
- 10.4 Traffic Systems
- 10.5 Terrain and Obstacle Proximity
- 10.6 Terrain Awareness & Warning System (TAWS) Display (Optional)
- Displaying Terrain on the TAWS Page
- Enable/Disable Aviation Data
- TAWS Inhibit
- Manual System Test
- Forward Looking Terrain Avoidance (FLTA)
- Premature Descent Alert (PDA)
- Excessive Descent Rate Alert (EDR)
- Negative Climb Rate After TakeoffAlert (NCR)
- “Five-Hundred” Aural Alert
- Displaying Terrain and Obstacles on the Navigation Map
- Pop-up Alerts
- TAWS Alerts Summary
- Alert Annunciations
- Section 11: Abnormal Operation
- Section 12: Annunciations & Alerts
- 12.1 Alert Level Definitions
- 12.2 NAV III Aircraft Alerts
- 12.3 CO Guardian Messages
- 12.4 AFCS Alerts
- 12.5 TAWS Alerts
- 12.6 Other G1000 Aural Alerts
- 12.7 G1000 System Annunciations
- 12.8 G1000 System Message Advisories
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347 Message Advisories
- GIA 63 Message Advisories
- GIA 63W Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GDL 69A Message Advisories
- GDC 74A Message Advisories
- Miscellaneous Message Advisories
- Index
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III
190-00384-08 Rev. A
12-15
SECTION 12 – ANNUNCIATIONS
& ALERTS
GIA 63 Message Advisories (Cont.)
Message Comments
ABORT APR – Loss of GPS navigation.
Abort approach.
Abort approach due to loss of GPS navigation.
TRUE APR – True north approach.
Change hdg reference to TRUE.
Displayed after passing the first waypoint of a true north approach when the nav
angle is set to ‘AUTO’.
GPS1 FAIL – GPS1 is inoperative.
A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver is
unavailable. The G1000 system should be serviced.
GPS2 FAIL – GPS2 is inoperative.
GPS1 SERVICE – GPS1 needs service.
Return unit for repair.
A failure has been detected in the GPS1 and/or GPS2 receiver. The receiver may still
be available. The G1000 system should be serviced.
GPS2 SERVICE – GPS2 needs service.
Return unit for repair.
NAV1 SERVICE – NAV1 needs service.
Return unit for repair.
A failure has been detected in the NAV1 and/or NAV2 receiver. The receiver may still
be available. The G1000 system should be serviced.
NAV2 SERVICE – NAV2 needs service.
Return unit for repair.
NAV1 RMT XFR – NAV1 remote
transfer key is stuck.
The remote NAV1 and/or NAV2 transfer switch is stuck in the enabled (or “pressed”)
state. Press the transfer switch again to cycle its operation. If the problem persists,
the G1000 system should be serviced.
NAV2 RMT XFR – NAV2 remote
transfer key is stuck.
G/S1 FAIL – G/S1 is inoperative.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The G1000
system should be serviced.
G/S2 FAIL – G/S2 is inoperative.
G/S1 SERVICE – G/S1 needs service.
Return unit for repair.
A failure has been detected in glideslope receiver 1 and/or receiver 2. The receiver
may still be available. The G1000 system should be serviced when possible.
G/S2 SERVICE – G/S2 needs service.
Return unit for repair.