Cockpit Reference Guide
Table Of Contents
- Section 1: System Overview
- Section 2: Flight Instruments
- Section 3: Engine Indication System (EIS)
- Section 4: NAV/COM and Transponder
- Section 5: Audio Panel
- Section 6: Automatic Flight Control
- Section 7: Navigation
- 7.1 Navigation Map Page
- 7.2 Direct-to Navigation
- 7.3 Navigating an Example Flight Plan
- 7.4 Airport Information
- 7.5 Intersection Information
- 7.6 NDB Information
- 7.7 VOR Information
- 7.8 User Waypoint Information Page
- 7.9 Nearest Airports
- 7.10 Nearest Intersections
- 7.11 Nearest NDB
- 7.12 Nearest VOR
- 7.13 Nearest User Waypoint
- 7.14 Nearest Frequencies
- 7.15 Nearest Airspaces
- Section 8: Flight Planning
- 8.1 User Defined Waypoints
- 8.2 Viewing the Active Flight Plan
- 8.3 Activate a Stored Flight Plan
- 8.4 Activate a Flight Plan Leg
- 8.5 Stop Navigating a Flight Plan
- 8.6 Invert Active Flight Plan
- 8.7 Create a New Flight Plan
- 8.8 Enter an Airway in a Flight Plan
- 8.9 Load a Departure
- 8.10 Load an Arrival
- 8.11 Load an Approach
- 8.12 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- 8.13 Store a Flight Plan
- 8.14 Edit a Stored Flight Plan
- 8.15 Delete a Waypoint from the Flight Plan
- 8.16 Invert and Activate a Stored Flight Plan
- 8.17 Copy a Flight Plan
- 8.18 Delete a Flight Plan
- 8.19 Graphical Flight Plan Creation
- 8.20 Trip Planning
- Section 9: Procedures
- Section 10: Hazard Avoidance
- 10.1 Customizing the Hazard Displays on the Navigation Map
- 10.2 STORMSCOPE® (Optional)
- 10.3 XM Weather (Service Optional)
- 10.4 Traffic Systems
- 10.5 Terrain and Obstacle Proximity
- 10.6 Terrain Awareness & Warning System (TAWS) Display (Optional)
- Displaying Terrain on the TAWS Page
- Enable/Disable Aviation Data
- TAWS Inhibit
- Manual System Test
- Forward Looking Terrain Avoidance (FLTA)
- Premature Descent Alert (PDA)
- Excessive Descent Rate Alert (EDR)
- Negative Climb Rate After TakeoffAlert (NCR)
- “Five-Hundred” Aural Alert
- Displaying Terrain and Obstacles on the Navigation Map
- Pop-up Alerts
- TAWS Alerts Summary
- Alert Annunciations
- Section 11: Abnormal Operation
- Section 12: Annunciations & Alerts
- 12.1 Alert Level Definitions
- 12.2 NAV III Aircraft Alerts
- 12.3 CO Guardian Messages
- 12.4 AFCS Alerts
- 12.5 TAWS Alerts
- 12.6 Other G1000 Aural Alerts
- 12.7 G1000 System Annunciations
- 12.8 G1000 System Message Advisories
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347 Message Advisories
- GIA 63 Message Advisories
- GIA 63W Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GDL 69A Message Advisories
- GDC 74A Message Advisories
- Miscellaneous Message Advisories
- Index
Garmin G1000 Cockpit Reference Guide for the Cessna Nav III
190-00384-08 Rev. A
12-14
SECTION 12 – ANNUNCIATIONS
& ALERTS
GIA 63 Message Advisories (Cont.)
Message Comments
MANIFEST – GIA1 software mismatch,
communication halted.
The GIA1 and/or GIA 2 has incorrect software installed. The G1000 system should
be serviced.
MANIFEST – GIA2 software mismatch,
communication halted.
COM1 TEMP – COM1 over temp.
Reducing transmitter power.
The system has detected an over temperature condition in COM1 and/or COM2. The
transmitter is operating at reduced power. If the problem persists, the G1000 system
should be serviced.
COM2 TEMP – COM2 over temp.
Reducing transmitter power.
COM1 SERVICE
– COM1 needs
service. Return unit for repair.
The system has detected a failure in COM1 and/or COM2. COM1 and/or COM2 may
still be usable. The G1000 system should be serviced when possible.
COM2 SERVICE
– COM2 needs
service. Return unit for repair.
COM1 PTT – COM1 push-to-talk key
is stuck.
The COM1 and/or COM2 external push-to-talk switch is stuck in the enable (or
“pressed”) position. Press the PTT switch again to cycle its operation.
If the problem persists, the G1000 system should be serviced.
COM2 PTT – COM2 push-to-talk key
is stuck.
COM1 RMT XFR – COM1 remote
transfer key is stuck.
The COM1 and/or COM2 transfer switch is stuck in the enabled (or “pressed”) posi-
tion. Press the transfer switch again to cycle its operation. If the problem persists,
the G1000 system should be serviced.
COM2 RMT XFR – COM2 remote
transfer key is stuck.
RAIM UNAVAIL
– RAIM is not
available from FAF to MAP waypoints.
GPS satellite coverage is insufficient to perform Receiver Autonomous Integrity
Monitoring (RAIM) from the FAF to the MAP waypoints.
LOI – GPS integrity lost. Crosscheck
with other NAVS.
Loss of GPS integrity monitoring.
GPS NAV LOST
– Loss of GPS naviga-
tion. Insufficient satellites.
Loss of GPS navigation due to insufficient satellites.
GPS NAV LOST
– Loss of GPS
navigation. Position error.
Loss of GPS navigation due to position error.
GPS NAV LOST
– Loss of GPS
navigation. GPS fail.
Loss of GPS navigation due to GPS failure.