Cockpit Reference Guide
Table Of Contents
- Section 1: System Overview
- Section 2: Flight Instruments
- Section 3: Engine Indication System (EIS)
- Section 4: NAV/COM and Transponder
- Section 5: Audio Panel
- Section 6: Automatic Flight Control
- Section 7: Navigation
- 7.1 Navigation Map Page
- 7.2 Direct-to Navigation
- 7.3 Navigating an Example Flight Plan
- 7.4 Airport Information
- 7.5 Intersection Information
- 7.6 NDB Information
- 7.7 VOR Information
- 7.8 User Waypoint Information Page
- 7.9 Nearest Airports
- 7.10 Nearest Intersections
- 7.11 Nearest NDB
- 7.12 Nearest VOR
- 7.13 Nearest User Waypoint
- 7.14 Nearest Frequencies
- 7.15 Nearest Airspaces
- Section 8: Flight Planning
- 8.1 User Defined Waypoints
- 8.2 Viewing the Active Flight Plan
- 8.3 Activate a Stored Flight Plan
- 8.4 Activate a Flight Plan Leg
- 8.5 Stop Navigating a Flight Plan
- 8.6 Invert Active Flight Plan
- 8.7 Create a New Flight Plan
- 8.8 Enter an Airway in a Flight Plan
- 8.9 Load a Departure
- 8.10 Load an Arrival
- 8.11 Load an Approach
- 8.12 Remove a Departure, Arrival, Approach, or Airway from a Flight Plan
- 8.13 Store a Flight Plan
- 8.14 Edit a Stored Flight Plan
- 8.15 Delete a Waypoint from the Flight Plan
- 8.16 Invert and Activate a Stored Flight Plan
- 8.17 Copy a Flight Plan
- 8.18 Delete a Flight Plan
- 8.19 Graphical Flight Plan Creation
- 8.20 Trip Planning
- Section 9: Procedures
- Section 10: Hazard Avoidance
- 10.1 Customizing the Hazard Displays on the Navigation Map
- 10.2 STORMSCOPE® (Optional)
- 10.3 XM Weather (Service Optional)
- 10.4 Traffic Systems
- 10.5 Terrain and Obstacle Proximity
- 10.6 Terrain Awareness & Warning System (TAWS) Display (Optional)
- Displaying Terrain on the TAWS Page
- Enable/Disable Aviation Data
- TAWS Inhibit
- Manual System Test
- Forward Looking Terrain Avoidance (FLTA)
- Premature Descent Alert (PDA)
- Excessive Descent Rate Alert (EDR)
- Negative Climb Rate After TakeoffAlert (NCR)
- “Five-Hundred” Aural Alert
- Displaying Terrain and Obstacles on the Navigation Map
- Pop-up Alerts
- TAWS Alerts Summary
- Alert Annunciations
- Section 11: Abnormal Operation
- Section 12: Annunciations & Alerts
- 12.1 Alert Level Definitions
- 12.2 NAV III Aircraft Alerts
- 12.3 CO Guardian Messages
- 12.4 AFCS Alerts
- 12.5 TAWS Alerts
- 12.6 Other G1000 Aural Alerts
- 12.7 G1000 System Annunciations
- 12.8 G1000 System Message Advisories
- MFD & PFD Message Advisories
- Database Message Advisories
- GMA 1347 Message Advisories
- GIA 63 Message Advisories
- GIA 63W Message Advisories
- GEA 71 Message Advisories
- GTX 33 Message Advisories
- GRS 77 Message Advisories
- GMU 44 Message Advisories
- GDL 69A Message Advisories
- GDC 74A Message Advisories
- Miscellaneous Message Advisories
- Index

Garmin G1000 Cockpit Reference Guide for the Cessna Nav III
190-00384-08 Rev. A
SECTION 7 – NAVIGATION
7-4
Enter a Direct-to Destination
1)
Press the Direct-to Key
( )
.
2)
Turn the large
FMS
Knob to place the cursor in the
desired selection field.
3)
Turn the small
FMS
Knob to begin selecting the
desired identifier, location, etc.
4)
Press the
ENT
Key.
5)
The cursor is now flashing on ‘ACTIVATE?’. If no
altitude constraint or course is desired, press the
ENT
Key to activate. To enter an altitude constraint,
proceed to step 6.
6)
Turn the large
FMS
Knob to place the cursor over
the ‘VNAV’ altitude field.
7)
Turn the small
FMS
Knob to enter the desired VNAV
altitude.
8)
Press the
ENT
Key. The option to select ‘MSL’ or
‘AGL’ is now displayed.
9)
Turn the small
FMS
Knob to select ‘MSL’ or ‘AGL’.
10)
Press the
ENT
Key. The cursor is placed in the
‘VNAV’ offset distance field.
11)
Turn the small
FMS
Knob to enter the desired target
altitude offset from the selected Direct-to.
12)
Press the
ENT
Key to highlight ‘Activate?’ or turn the
large
FMS
Knob to highlight the ‘COURSE’ field.
13)
Turn the small
FMS
Knob to enter the desired course
to the waypoint.
14)
Press the
ENT
Key to highlight ‘ACTIVATE?’.
15)
Press the
ENT
Key again to activate the Direct-to.
Select a Direct-to Destination to a Flight Plan
Waypoint
1)
While navigating an active flight plan, press the
Direct-to
( )
Key.
2)
Turn the small
FMS
Knob to the left to display a list
of flight plan waypoints as shown in Figure 7-8.
Figure 7-8 Flight Plan Waypoint List (PFD)
3)
Turn the large
FMS
Knob to select the desired
waypoint.
4)
Press the
ENT
Key. The cursor is now displayed on
‘ACTIVATE?’.
5)
Press the
ENT
Key again to activate a Direct-to.
Select a Direct-to Destination to a Nearest
Airport
1)
Press the
Direct-to
( )
Key.
2)
Turn the small
FMS
Knob to the left. Initially, a
flight plan waypoint list is displayed as in Figure
7-8. The list is only populated when navigating a
flight plan.
Figure 7-9 Nearest Airport List (PFD)
3)
Turn the small
FMS
Knob to the right to display the
‘NRST’ airports to the aircraft’s current position as
shown in Figure 7-9.










