Cockpit Reference Guide
Table Of Contents
- Copyright
- Record of Revisions
- Table of Contents
- List of Figures
- List of Tables
- WARRANTY
- Warnings and Cautions
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- Appendix A
- Index
- Figure 1-1 G1000 Controls
- Figure 1-2 G1000 Power-Up
- Figure 1-3 G1000 Normal Mode
- Figure 1-4 G1000 Reversionary Mode: Failed PFD
- Figure 2-1 Default PFD Information
- Figure 2-2 Additional PFD Information
- Figure 2-3 PFD Setup Menu
- Figure 2-4 PFD Softkeys (1 of 2)
- Figure 2-4 PFD Softkeys (2 of 2)
- Figure 2-5 Airspeed Indicator
- Figure 2-6 Red Pointer at Vne
- Figure 2-7 Attitude Indicator
- Figure 2-8 Attitude Indicator Nose High
- Figure 2-9 Attitude Indicator Nose Low
- Figure 2-10 Altimeter
- Figure 2-11 Colors Associated with the Altitude Alerter
- Figure 2-12 Altimeter within 1,000 ft. of Reference Altitude
- Figure 2-13 Altimeter within 200 ft. of Reference Altitude
- Figure 2-14 Altimeter (Metric)
- Figure 2-16 Marker Beacon and Vertical Deviation
- Figure 2-16 Vertical Speed Indicator
- Figure 2-17 ARC HSI
- Figure 2-18 Horizontal Situation Indicator
- Figure 2-20 Turn Rate Indicator and Trend Vector
- Figure 2-21 Selected Course Box
- Figure 2-22 HSI with Bearing Information
- Figure 2-24 BRG2 Information Window
- Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2
- Figure 2-26 Communication Frequency Window
- Figure 2-27 Navigation Frequency Window
- Figure 2-28 Navigation Status Bars
- Figure 2-28 Navigation Status Bar Message
- Figure 2-29 Transponder Status Bar
- Figure 3-1 Front Panel Controls
- Figure 3-2 Transceivers
- Figure 3-3 Split COM, PA and Speaker
- Figure 3-4 Marker Beacon
- Figure 3-5 Marker Beacon Signal Indicator Lights on the PFD
- Figure 3-6 Aircraft Radios
- Figure 3-7 ICS Isolation
- Figure 3-8 Reversionary Mode
- Figure 4-2 MFD Softkeys
- Figure 4-3 ENGINE Page (Normally Aspirated)
- Figure 4-4 ENGINE Page (Turbocharged)
- Figure 4-5 Page Group Window
- Figure 4-6 Page Title Window
- Figure 4-6 Menu With Options
- Figure 4-7 Menu With No Options
- Figure 4-8 Navigation Map Page
- Figure 4-9 Navigation Map Range
- Figure 4-10 Navigation Map Panning
- Figure 4-11 TRAFFIC, TOPO and TERRAIN Softkeys
- Figure 4-12 Topography Scale
- Figure 4-13 MFD Navigation Status Window
- Figure 4-14 Navigation Map Page Menu Options
- Figure 4-15 Traffic Map Page
- Figure 4-16 Weather Map Page
- Figure 4-17 Terrain Scale
- Figure 4-18 Direct-to Page
- Figure 4-19 Flight Plan Waypoint Direct-to
- Figure 4-20 Nearest Airport Direct-to
- Figure 4-21 Manual Course Direct-to
- Figure 4-22 New Flight Plan
- Figure 4-23 Remove Waypoint Confirmation
- Figure 4-24 Removing an Approach
- Figure 4-25 Flight Plan Catalog Page
- Figure 4-26 Flight Plan Catalog Page Options
- Figure 4-27 Activate Stored Flight Plan Confirmation
- Figure 4-28 Delete Flight Plan Confirmation
- Figure 4-29 Procedures Page
- Figure 4-30 Selecting an Approach Procedure
- Figure 4-31 Selecting an Approach Transition
- Figure 4-32 Activating an Approach Procedure
- Figure 4-33 Approach with No Procedure Turn
- Figure 4-34 Flying the Missed Approach
- Figure 4-35 Flying the Procedure Turn
- Figure 4-36 Flying the DME Arc and Vectors to the DME Arc
- Figure 4-37 Flying a Holding Pattern
- Figure A-1 G1000 Alerting System
- Figure A-2 ADVISORY Softkey Annunciation
- Figure A-3 G1000 System Failure Annunciations
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- A.1 Introduction
- A.2 Alert Levels
- A.3 Mooney Specific Aircraft Alerts
- A.4 G1000 System Annunciations
- A.5 G1000 System Message Advisories
Garmin G1000 Cockpit Reference Guide for Mooney M20M & M20R
70
SECTION 4 – MFD
4.8 DIRECT-TO NAVIGATION
The “Direct-to” function provides a quick method of
setting a course to a destination waypoint. Once a Di-
rect-to is activated, the G1000 establishes a point-to-point
course line from the present position to the selected Di-
rect-to destination. If the course change is greater than
30 degrees, a course extension is offset from the present
position to allow a standard rate turn to intercept the Di-
rect-to course line. Note that the CDI (HSI) needle will
not be immediately centered in this case. Direct-to course
guidance is provided until the Direct-to is cancelled or
replaced by a new destination, and the navigation data is
displayed on the Navigation Map Page.
Identifier
Facility Name
City
Map of the
Selected
Waypoint
Bearing
Distance
Direct-to
Course
Region
Latitude/
Longitude
Symbol
Nearest Airport
Selection
Map Orientation
Map Range
Flight Plan Way
-
point Selection
Activate Field
Figure 4-18 Direct-to Page
To select a direct-to destination:
1. Press the
Direct-to
key. The Direct-to page
is displayed with the destination field high-
lighted.
2. Turn the
small FMS
knob to enter the first letter
of the destination waypoint identifier. The
destination waypoint may be an airport, VOR,
NDB, intersection or user waypoint, as long as
it is in the database or stored in memory as a
user waypoint. Turn the
large FMS
knob to the
right to move the cursor to the next character
position.
3. Repeat steps 2 and 3 to spell out the rest of
the waypoint identifier.
4. Press the
ENT
key to confirm the identifier. The
‘Activate?’ field is highlighted.
5. Press the
ENT
key to activate a Direct-to course
to the selected destination.
If navigating to a waypoint and the aircraft moves off
course, the direct-to feature can be used to re-center the
CDI (HSI) needle and proceed to the same waypoint.
To re-center the CDI (HSI) needle to the
same destination waypoint:
1. Press the Direct-to key, followed by press
-
ing the
ENT
key twice. NOTE: If navigating
an approach with the missed approach point
(MAP) as the current destination, re-centering
the CDI (HSI) needle with the Direct-to key
cancels the approach.