Cockpit Reference Guide
Table Of Contents
- Copyright
- Record of Revisions
- Table of Contents
- List of Figures
- List of Tables
- WARRANTY
- Warnings and Cautions
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- Appendix A
- Index
- Figure 1-1 G1000 Controls
- Figure 1-2 G1000 Power-Up
- Figure 1-3 G1000 Normal Mode
- Figure 1-4 G1000 Reversionary Mode: Failed PFD
- Figure 2-1 Default PFD Information
- Figure 2-2 Additional PFD Information
- Figure 2-3 PFD Setup Menu
- Figure 2-4 PFD Softkeys (1 of 2)
- Figure 2-4 PFD Softkeys (2 of 2)
- Figure 2-5 Airspeed Indicator
- Figure 2-6 Red Pointer at Vne
- Figure 2-7 Attitude Indicator
- Figure 2-8 Attitude Indicator Nose High
- Figure 2-9 Attitude Indicator Nose Low
- Figure 2-10 Altimeter
- Figure 2-11 Colors Associated with the Altitude Alerter
- Figure 2-12 Altimeter within 1,000 ft. of Reference Altitude
- Figure 2-13 Altimeter within 200 ft. of Reference Altitude
- Figure 2-14 Altimeter (Metric)
- Figure 2-16 Marker Beacon and Vertical Deviation
- Figure 2-16 Vertical Speed Indicator
- Figure 2-17 ARC HSI
- Figure 2-18 Horizontal Situation Indicator
- Figure 2-20 Turn Rate Indicator and Trend Vector
- Figure 2-21 Selected Course Box
- Figure 2-22 HSI with Bearing Information
- Figure 2-24 BRG2 Information Window
- Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2
- Figure 2-26 Communication Frequency Window
- Figure 2-27 Navigation Frequency Window
- Figure 2-28 Navigation Status Bars
- Figure 2-28 Navigation Status Bar Message
- Figure 2-29 Transponder Status Bar
- Figure 3-1 Front Panel Controls
- Figure 3-2 Transceivers
- Figure 3-3 Split COM, PA and Speaker
- Figure 3-4 Marker Beacon
- Figure 3-5 Marker Beacon Signal Indicator Lights on the PFD
- Figure 3-6 Aircraft Radios
- Figure 3-7 ICS Isolation
- Figure 3-8 Reversionary Mode
- Figure 4-2 MFD Softkeys
- Figure 4-3 ENGINE Page (Normally Aspirated)
- Figure 4-4 ENGINE Page (Turbocharged)
- Figure 4-5 Page Group Window
- Figure 4-6 Page Title Window
- Figure 4-6 Menu With Options
- Figure 4-7 Menu With No Options
- Figure 4-8 Navigation Map Page
- Figure 4-9 Navigation Map Range
- Figure 4-10 Navigation Map Panning
- Figure 4-11 TRAFFIC, TOPO and TERRAIN Softkeys
- Figure 4-12 Topography Scale
- Figure 4-13 MFD Navigation Status Window
- Figure 4-14 Navigation Map Page Menu Options
- Figure 4-15 Traffic Map Page
- Figure 4-16 Weather Map Page
- Figure 4-17 Terrain Scale
- Figure 4-18 Direct-to Page
- Figure 4-19 Flight Plan Waypoint Direct-to
- Figure 4-20 Nearest Airport Direct-to
- Figure 4-21 Manual Course Direct-to
- Figure 4-22 New Flight Plan
- Figure 4-23 Remove Waypoint Confirmation
- Figure 4-24 Removing an Approach
- Figure 4-25 Flight Plan Catalog Page
- Figure 4-26 Flight Plan Catalog Page Options
- Figure 4-27 Activate Stored Flight Plan Confirmation
- Figure 4-28 Delete Flight Plan Confirmation
- Figure 4-29 Procedures Page
- Figure 4-30 Selecting an Approach Procedure
- Figure 4-31 Selecting an Approach Transition
- Figure 4-32 Activating an Approach Procedure
- Figure 4-33 Approach with No Procedure Turn
- Figure 4-34 Flying the Missed Approach
- Figure 4-35 Flying the Procedure Turn
- Figure 4-36 Flying the DME Arc and Vectors to the DME Arc
- Figure 4-37 Flying a Holding Pattern
- Figure A-1 G1000 Alerting System
- Figure A-2 ADVISORY Softkey Annunciation
- Figure A-3 G1000 System Failure Annunciations
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- A.1 Introduction
- A.2 Alert Levels
- A.3 Mooney Specific Aircraft Alerts
- A.4 G1000 System Annunciations
- A.5 G1000 System Message Advisories
Garmin G1000 Cockpit Reference Guide for Mooney M20M & M20R
64
SECTION 4 – MFD
Operating Mode
Once the aircraft is airborne (determined by sys
-
tem configuration at the time of installation) the system
switches from standby mode to operating mode. The
G1000 displays ‘OPERATE’ in the upper left hand corner
of the display and begins to display traffic on the Traffic or
Map Page. The TIS Traffic Advisory (TA) should alert
the crew to use additional vigilance to identify the in-
truding aircraft. Any time the traffic symbol becomes a
yellow circle or a voice warning is announced, conduct
a visual search for the intruder. Maintain visual con-
tact to ensure safe operation.
Once the aircraft is on the ground (determined by
system configuration at the time of installation) the
system switches from operating mode to standby mode. The
Traffic Map Page displays ‘STANDBY’.
• STANDBY – when the Traffic Map Page displays
‘STANDBY’ in the status box located in the upper
left corner of the Traffic Map Page, the TIS system
is in standby mode and cannot display traffic data.
• OPERATE – when the Traffic Map Page displays
‘OPERATE’ in the status box located in the left
corner of the Traffic Map Page, the TIS system is
in operational mode and available to display traf-
fic on the Traffic or Map Page.
The pilot can switch between the standby (STBY) and
operate (ON) modes of operation to manually override
automatic operation using the page menu or softkeys.
To switch between operating modes:
1. Press the
MODE
softkey.
2. Press the
STBY
or
ON
softkey to switch between
modes. ‘STANDBY’ or ‘OPERATE’ is displayed
in the status box located in the upper left
corner of the Traffic Map Page OR:
3. Press the
MENU
key. The page menu is
displayed with ‘Standby Mode’ or ‘Operate
Mode’ highlighted. Press the
ENT
key on the
desired selection.
TIS Audio Alert
A TIS audio alert is generated whenever the number
of TAs on the Traffic Map Page display increases from one
scan to the next. The limiting to TAs only reduces the
amount of “nuisance” alerting due to proximate aircraft.
For example, when the first TA is displayed, the pilot is
alerted audibly. So long as a single TA aircraft remains on
the TIS display, no further audio alert is generated. If a
second (or more) TA aircraft appear on the display, a new
audio alert is sounded. If the number of TAs on the TIS
display decreases and then increases, a new audio alert is
sounded. The TIS audio alert is also generated whenever
TIS service becomes unavailable. The volume of the au
-
dio alert (including the choice between a male or female
voice) is configured during installation. The following
TIS audio alerts are available:
• “Traffic” - TIS traffic alert is received.
• “Traffic Not Available” - TIS service is not available
or out of range.