Cockpit Reference Guide
Table Of Contents
- Copyright
- Record of Revisions
- Table of Contents
- List of Figures
- List of Tables
- WARRANTY
- Warnings and Cautions
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- Appendix A
- Index
- Figure 1-1 G1000 Controls
- Figure 1-2 G1000 Power-Up
- Figure 1-3 G1000 Normal Mode
- Figure 1-4 G1000 Reversionary Mode: Failed PFD
- Figure 2-1 Default PFD Information
- Figure 2-2 Additional PFD Information
- Figure 2-3 PFD Setup Menu
- Figure 2-4 PFD Softkeys (1 of 2)
- Figure 2-4 PFD Softkeys (2 of 2)
- Figure 2-5 Airspeed Indicator
- Figure 2-6 Red Pointer at Vne
- Figure 2-7 Attitude Indicator
- Figure 2-8 Attitude Indicator Nose High
- Figure 2-9 Attitude Indicator Nose Low
- Figure 2-10 Altimeter
- Figure 2-11 Colors Associated with the Altitude Alerter
- Figure 2-12 Altimeter within 1,000 ft. of Reference Altitude
- Figure 2-13 Altimeter within 200 ft. of Reference Altitude
- Figure 2-14 Altimeter (Metric)
- Figure 2-16 Marker Beacon and Vertical Deviation
- Figure 2-16 Vertical Speed Indicator
- Figure 2-17 ARC HSI
- Figure 2-18 Horizontal Situation Indicator
- Figure 2-20 Turn Rate Indicator and Trend Vector
- Figure 2-21 Selected Course Box
- Figure 2-22 HSI with Bearing Information
- Figure 2-24 BRG2 Information Window
- Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2
- Figure 2-26 Communication Frequency Window
- Figure 2-27 Navigation Frequency Window
- Figure 2-28 Navigation Status Bars
- Figure 2-28 Navigation Status Bar Message
- Figure 2-29 Transponder Status Bar
- Figure 3-1 Front Panel Controls
- Figure 3-2 Transceivers
- Figure 3-3 Split COM, PA and Speaker
- Figure 3-4 Marker Beacon
- Figure 3-5 Marker Beacon Signal Indicator Lights on the PFD
- Figure 3-6 Aircraft Radios
- Figure 3-7 ICS Isolation
- Figure 3-8 Reversionary Mode
- Figure 4-2 MFD Softkeys
- Figure 4-3 ENGINE Page (Normally Aspirated)
- Figure 4-4 ENGINE Page (Turbocharged)
- Figure 4-5 Page Group Window
- Figure 4-6 Page Title Window
- Figure 4-6 Menu With Options
- Figure 4-7 Menu With No Options
- Figure 4-8 Navigation Map Page
- Figure 4-9 Navigation Map Range
- Figure 4-10 Navigation Map Panning
- Figure 4-11 TRAFFIC, TOPO and TERRAIN Softkeys
- Figure 4-12 Topography Scale
- Figure 4-13 MFD Navigation Status Window
- Figure 4-14 Navigation Map Page Menu Options
- Figure 4-15 Traffic Map Page
- Figure 4-16 Weather Map Page
- Figure 4-17 Terrain Scale
- Figure 4-18 Direct-to Page
- Figure 4-19 Flight Plan Waypoint Direct-to
- Figure 4-20 Nearest Airport Direct-to
- Figure 4-21 Manual Course Direct-to
- Figure 4-22 New Flight Plan
- Figure 4-23 Remove Waypoint Confirmation
- Figure 4-24 Removing an Approach
- Figure 4-25 Flight Plan Catalog Page
- Figure 4-26 Flight Plan Catalog Page Options
- Figure 4-27 Activate Stored Flight Plan Confirmation
- Figure 4-28 Delete Flight Plan Confirmation
- Figure 4-29 Procedures Page
- Figure 4-30 Selecting an Approach Procedure
- Figure 4-31 Selecting an Approach Transition
- Figure 4-32 Activating an Approach Procedure
- Figure 4-33 Approach with No Procedure Turn
- Figure 4-34 Flying the Missed Approach
- Figure 4-35 Flying the Procedure Turn
- Figure 4-36 Flying the DME Arc and Vectors to the DME Arc
- Figure 4-37 Flying a Holding Pattern
- Figure A-1 G1000 Alerting System
- Figure A-2 ADVISORY Softkey Annunciation
- Figure A-3 G1000 System Failure Annunciations
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- A.1 Introduction
- A.2 Alert Levels
- A.3 Mooney Specific Aircraft Alerts
- A.4 G1000 System Annunciations
- A.5 G1000 System Message Advisories
Garmin G1000 Cockpit Reference Guide for Mooney M20M & M20R
63
SECTION 4 – MFD
TIS Symbology
TIS traffic is displayed on the Traffic Map Page accord-
ing to TCAS symbology. A Traffic Advisory (TA) symbol
is displayed as a solid yellow circle (or half circle on the
outer range ring if the traffic is outside the range of the
dedicated traffic page). All other traffic is displayed as a
hollow white diamond. Altitude deviation from the user’s
aircraft altitude is displayed above the target symbol if
they are above own aircraft altitude, and below the sym-
bol if they are below own aircraft altitude. Altitude trend
is displayed as an up arrow (+500 ft/min), down arrow
(-500 ft/min), or no symbol if less than 500 ft/min rate in
either direction. Other symbols:
• Other Traffic – this symbol represents traffic
detected within the selected display range that
does not generate a TA.
• Traffic Advisory (TA) – this symbol is generated
when traffic meets the advisory criteria described
previously.
• Traffic Ground Track is indicated on the Traffic
Map Page by a “target track vector”. The track
vector line is projected from the traffic advisory
symbol and is drawn at any angle necessary to
represent the current track of the traffic advisory
data.
Item Symbol
Traffic
Proximate Traffic
Traffic Advisory, Out of Range
Traffic Advisory
Traffic Map Page Operations
Power-Up Test
The TIS interface performs an automatic test during
power-up. If the system passes the power-up test, the
standby screen is displayed on the Traffic Map Page. If the
system passes the power-up test, and the aircraft is air-
borne, traffic is displayed on the Traffic Page in the operat-
ing mode.
If the system fails the power up test, the ‘NO DATA’,
‘DATA FAILED’, or ‘FAILED’ message is displayed. Con
-
tact your Mooney service center or Garmin dealer for cor-
rective action if the ‘DATA FAILED’, or ‘FAILED’ message
is displayed. The ‘FAILED’ message indicates the GTX
33 transponder has failed. The ‘DATA FAILED’ message
indicates data is being received from the GTX 33 but a
failure was detected in the data stream. The ‘NO DATA’
message indicates that data is not being received from the
GTX 33.
Changing the Map Range
To change the map range:
1. Turn the joystick clockwise to zoom out, or turn
the joystick counter-clockwise to zoom in. Map
ranges are 2 nm, 6 nm, and 12 nm.
NOTE: Traffic Information Service (TIS) is not
available in all areas.