Cockpit Reference Guide
Table Of Contents
- Copyright
- Record of Revisions
- Table of Contents
- List of Figures
- List of Tables
- WARRANTY
- Warnings and Cautions
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- Appendix A
- Index
- Figure 1-1 G1000 Controls
- Figure 1-2 G1000 Power-Up
- Figure 1-3 G1000 Normal Mode
- Figure 1-4 G1000 Reversionary Mode: Failed PFD
- Figure 2-1 Default PFD Information
- Figure 2-2 Additional PFD Information
- Figure 2-3 PFD Setup Menu
- Figure 2-4 PFD Softkeys (1 of 2)
- Figure 2-4 PFD Softkeys (2 of 2)
- Figure 2-5 Airspeed Indicator
- Figure 2-6 Red Pointer at Vne
- Figure 2-7 Attitude Indicator
- Figure 2-8 Attitude Indicator Nose High
- Figure 2-9 Attitude Indicator Nose Low
- Figure 2-10 Altimeter
- Figure 2-11 Colors Associated with the Altitude Alerter
- Figure 2-12 Altimeter within 1,000 ft. of Reference Altitude
- Figure 2-13 Altimeter within 200 ft. of Reference Altitude
- Figure 2-14 Altimeter (Metric)
- Figure 2-16 Marker Beacon and Vertical Deviation
- Figure 2-16 Vertical Speed Indicator
- Figure 2-17 ARC HSI
- Figure 2-18 Horizontal Situation Indicator
- Figure 2-20 Turn Rate Indicator and Trend Vector
- Figure 2-21 Selected Course Box
- Figure 2-22 HSI with Bearing Information
- Figure 2-24 BRG2 Information Window
- Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2
- Figure 2-26 Communication Frequency Window
- Figure 2-27 Navigation Frequency Window
- Figure 2-28 Navigation Status Bars
- Figure 2-28 Navigation Status Bar Message
- Figure 2-29 Transponder Status Bar
- Figure 3-1 Front Panel Controls
- Figure 3-2 Transceivers
- Figure 3-3 Split COM, PA and Speaker
- Figure 3-4 Marker Beacon
- Figure 3-5 Marker Beacon Signal Indicator Lights on the PFD
- Figure 3-6 Aircraft Radios
- Figure 3-7 ICS Isolation
- Figure 3-8 Reversionary Mode
- Figure 4-2 MFD Softkeys
- Figure 4-3 ENGINE Page (Normally Aspirated)
- Figure 4-4 ENGINE Page (Turbocharged)
- Figure 4-5 Page Group Window
- Figure 4-6 Page Title Window
- Figure 4-6 Menu With Options
- Figure 4-7 Menu With No Options
- Figure 4-8 Navigation Map Page
- Figure 4-9 Navigation Map Range
- Figure 4-10 Navigation Map Panning
- Figure 4-11 TRAFFIC, TOPO and TERRAIN Softkeys
- Figure 4-12 Topography Scale
- Figure 4-13 MFD Navigation Status Window
- Figure 4-14 Navigation Map Page Menu Options
- Figure 4-15 Traffic Map Page
- Figure 4-16 Weather Map Page
- Figure 4-17 Terrain Scale
- Figure 4-18 Direct-to Page
- Figure 4-19 Flight Plan Waypoint Direct-to
- Figure 4-20 Nearest Airport Direct-to
- Figure 4-21 Manual Course Direct-to
- Figure 4-22 New Flight Plan
- Figure 4-23 Remove Waypoint Confirmation
- Figure 4-24 Removing an Approach
- Figure 4-25 Flight Plan Catalog Page
- Figure 4-26 Flight Plan Catalog Page Options
- Figure 4-27 Activate Stored Flight Plan Confirmation
- Figure 4-28 Delete Flight Plan Confirmation
- Figure 4-29 Procedures Page
- Figure 4-30 Selecting an Approach Procedure
- Figure 4-31 Selecting an Approach Transition
- Figure 4-32 Activating an Approach Procedure
- Figure 4-33 Approach with No Procedure Turn
- Figure 4-34 Flying the Missed Approach
- Figure 4-35 Flying the Procedure Turn
- Figure 4-36 Flying the DME Arc and Vectors to the DME Arc
- Figure 4-37 Flying a Holding Pattern
- Figure A-1 G1000 Alerting System
- Figure A-2 ADVISORY Softkey Annunciation
- Figure A-3 G1000 System Failure Annunciations
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- A.1 Introduction
- A.2 Alert Levels
- A.3 Mooney Specific Aircraft Alerts
- A.4 G1000 System Annunciations
- A.5 G1000 System Message Advisories
Garmin G1000 Cockpit Reference Guide for Mooney M20M & M20R
30
SECTION 2 – PFD
Transponder Status Bar
The Transponder Status Bar displays the transponder
code, reply symbol, and mode of operation. TIS (Traffic
Information System) surveillance data up-linked by Air
Traffic Control (ATC) radar through the GTX33 Mode S
Transponder appears on the Inset Map (PFD), Navigation
and Traffic Map Pages on the MFD (refer to the MFD Pilot’s
Guide). If the transponder is configured with
Automated
Airborne Determination, normal operation begins when
lift off is sensed. When the aircraft is on the ground, the
window automatically displays “GND”. The transponder
does not respond to ATCRBS interrogations when GND is
annunciated. If a delay time is set in Configuration Mode,
the transponder waits a specified length of time after land
-
ing before changing to
GND mode.
Transponder Operation
Pressing the
XPDR softkey displays the second-level
softkeys:
• STBY – Selects standby mode. When in standby
mode, the transponder does not reply to any
interrogations.
• ON – Selects Mode A. In this mode, the transpon-
der replies to interrogations, as indicated by the
Reply Symbol (R). Replies do not include altitude
information.
• ALT – Selects Mode C. In ALT mode, the tran-
sponder replies to identification and altitude
interrogations as indicated by the Reply Symbol
(R). Replies to altitude interrogations include the
standard pressure altitude received from an exter
-
nal altitude source, which is not adjusted for baro
-
metric pressure. The ALT mode may be selected
in aircraft not equipped with an optional altitude
encoder; however, the reply signal will only reply
to mode A interrogations. The transponder also
responds to interrogations from TCAS equipped
aircraft.
• VFR – Sets the transponder code to the pre-pro-
grammed VFR code selected in Configuration
Mode (this is set to 1200 at the factory).
• CODE – Displays the transponder code selection
softkeys, which includes the digits 0-7 and BKSP.
• IDENT – Pressing the IDENT softkey activates
the Special Position Identification (SPI) Pulse for
18 seconds, identifying the transponder return on
the ATC screen.
Transponder Code Selection
Transponder code selection is performed with eight
softkeys (0-7) providing 4,096 active identification codes.
Pushing one of those keys begins the code selection se
-
quence. The new code is activated five seconds after the
fourth digit is entered. Pressing the BKSP softkey removes
one digit at a time until the status bar is empty (refer to the
Mode S Transponder Pilot’s Guide).
Figure 2-30 Transponder Status Bar
2.5 ALERTS AND ANNUNCIATIONS
Alerts and Annunciations that appear on the PFD are
described in detail in Appendix A of this Cockpit Refer-
ence Guide.