Cockpit Reference Guide
Table Of Contents
- Copyright
- Record of Revisions
- Table of Contents
- List of Figures
- List of Tables
- WARRANTY
- Warnings and Cautions
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- Appendix A
- Index
- Figure 1-1 G1000 Controls
- Figure 1-2 G1000 Power-Up
- Figure 1-3 G1000 Normal Mode
- Figure 1-4 G1000 Reversionary Mode: Failed PFD
- Figure 2-1 Default PFD Information
- Figure 2-2 Additional PFD Information
- Figure 2-3 PFD Setup Menu
- Figure 2-4 PFD Softkeys (1 of 2)
- Figure 2-4 PFD Softkeys (2 of 2)
- Figure 2-5 Airspeed Indicator
- Figure 2-6 Red Pointer at Vne
- Figure 2-7 Attitude Indicator
- Figure 2-8 Attitude Indicator Nose High
- Figure 2-9 Attitude Indicator Nose Low
- Figure 2-10 Altimeter
- Figure 2-11 Colors Associated with the Altitude Alerter
- Figure 2-12 Altimeter within 1,000 ft. of Reference Altitude
- Figure 2-13 Altimeter within 200 ft. of Reference Altitude
- Figure 2-14 Altimeter (Metric)
- Figure 2-16 Marker Beacon and Vertical Deviation
- Figure 2-16 Vertical Speed Indicator
- Figure 2-17 ARC HSI
- Figure 2-18 Horizontal Situation Indicator
- Figure 2-20 Turn Rate Indicator and Trend Vector
- Figure 2-21 Selected Course Box
- Figure 2-22 HSI with Bearing Information
- Figure 2-24 BRG2 Information Window
- Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2
- Figure 2-26 Communication Frequency Window
- Figure 2-27 Navigation Frequency Window
- Figure 2-28 Navigation Status Bars
- Figure 2-28 Navigation Status Bar Message
- Figure 2-29 Transponder Status Bar
- Figure 3-1 Front Panel Controls
- Figure 3-2 Transceivers
- Figure 3-3 Split COM, PA and Speaker
- Figure 3-4 Marker Beacon
- Figure 3-5 Marker Beacon Signal Indicator Lights on the PFD
- Figure 3-6 Aircraft Radios
- Figure 3-7 ICS Isolation
- Figure 3-8 Reversionary Mode
- Figure 4-2 MFD Softkeys
- Figure 4-3 ENGINE Page (Normally Aspirated)
- Figure 4-4 ENGINE Page (Turbocharged)
- Figure 4-5 Page Group Window
- Figure 4-6 Page Title Window
- Figure 4-6 Menu With Options
- Figure 4-7 Menu With No Options
- Figure 4-8 Navigation Map Page
- Figure 4-9 Navigation Map Range
- Figure 4-10 Navigation Map Panning
- Figure 4-11 TRAFFIC, TOPO and TERRAIN Softkeys
- Figure 4-12 Topography Scale
- Figure 4-13 MFD Navigation Status Window
- Figure 4-14 Navigation Map Page Menu Options
- Figure 4-15 Traffic Map Page
- Figure 4-16 Weather Map Page
- Figure 4-17 Terrain Scale
- Figure 4-18 Direct-to Page
- Figure 4-19 Flight Plan Waypoint Direct-to
- Figure 4-20 Nearest Airport Direct-to
- Figure 4-21 Manual Course Direct-to
- Figure 4-22 New Flight Plan
- Figure 4-23 Remove Waypoint Confirmation
- Figure 4-24 Removing an Approach
- Figure 4-25 Flight Plan Catalog Page
- Figure 4-26 Flight Plan Catalog Page Options
- Figure 4-27 Activate Stored Flight Plan Confirmation
- Figure 4-28 Delete Flight Plan Confirmation
- Figure 4-29 Procedures Page
- Figure 4-30 Selecting an Approach Procedure
- Figure 4-31 Selecting an Approach Transition
- Figure 4-32 Activating an Approach Procedure
- Figure 4-33 Approach with No Procedure Turn
- Figure 4-34 Flying the Missed Approach
- Figure 4-35 Flying the Procedure Turn
- Figure 4-36 Flying the DME Arc and Vectors to the DME Arc
- Figure 4-37 Flying a Holding Pattern
- Figure A-1 G1000 Alerting System
- Figure A-2 ADVISORY Softkey Annunciation
- Figure A-3 G1000 System Failure Annunciations
- Section 1: Introduction
- Section 2: Primary Flight Display
- Section 3: Audio Panel
- Section 4: Multi Function Display
- 4.1 Introduction
- 4.2 MFD Softkeys
- 4.3 Engine Indication System Window
- ENGINE Page
- Manifold Pressure Gauge
- Tachometer
- Fuel Qty Indicator
- Fuel Flow Indicator (Normally Aspirated)
- Fuel Pressure Indicator (Turbocharged Only)
- Oil Pressure Indicator
- Oil Temperature Indicator
- EGT Indicator (Normally Aspirated)
- TIT Indicator (Turbocharged Only)
- CHT Indicator
- Voltmeter
- Ammeter
- Rudder Trim Indicator
- Elevator Trim Indicator
- Flaps Position Indicator
- 4.3 MFD Page Groups
- 4.4 Navigation Map Page
- Navigation Map Page Operations
- Changing the Map Orientation
- Clearing Lightning Data
- Selecting a Map Range
- Using the Auto Zoom Feature
- Identifying Aviation Map Data
- Decluttering the Map
- Map Panning
- Displaying Topographic Data on the Navigation Map Page
- Displaying Terrain Data on the Navigation Map Page
- Displaying Traffic on the Navigation Map Page
- Displaying Lightning Data on the Navigation Map Page
- Lightning Data Display Range
- MFD Navigation Status Window
- Navigation Map Page Menu
- Navigation Map Page Operations
- 4.5 Traffic Map Page
- 4.6 WEATHER MAP Page
- 4.7 Terrain Proximity Page
- 4.8 Direct-To Navigation
- 4.9 Flight Plans
- 4.10 Procedures
- A.1 Introduction
- A.2 Alert Levels
- A.3 Mooney Specific Aircraft Alerts
- A.4 G1000 System Annunciations
- A.5 G1000 System Message Advisories
Garmin G1000 Cockpit Reference Guide for Mooney M20M & M20R
27
SECTION 2 – PFD
Navigation Source
The HSI can display two sources of navigation, GPS
or NAV (VOR, localizer, and glideslope). In GPS mode
the flight plan legs are sequenced automatically. Enabling
OBS mode suspends auto sequencing of waypoints, but
retains the current “active to” waypoint as your navigation
reference even after passing the waypoint. When OBS is
disabled the GPS returns to normal operation, with auto
-
matic sequencing of waypoints. OBS mode also allows
the pilot to set the desired course TO/FROM a waypoint.
Color indicates the current navigation source, magenta
(for GPS ) or green (for NAV). As the user crosses the
MAP, “SUSP” appears on the HSI in place of OBS and the
OBS softkey now reads “SUSP”, indicating that automatic
sequencing of approach waypoints is suspended at the
MAP. A yellow ‘INTEG’ and ‘WARN’ may appear on the
HSI when the following occurs:
• INTEG – RAIM is not available
• WARN – GPS detects a position error
To change between navigation sources:
1. Press the
CDI softkey to change from GPS to
NAV1. This will place the cyan tuning box over
the NAV1 standby frequency in the upper left
corner of the PFD.
2. Press the
CDI softkey again to change from
NAV1 to NAV2. This will place the cyan tuning
box over the NAV2 standby frequency.
3. Press the
CDI
softkey a third time to return to
GPS.
To enable/disable OBS mode while navigating
with GPS
:
1. Press the
OBS softkey to select OBS Mode.
2. Turn the small CRS knob to select the desired
course TO/FROM the waypoint.
3. Press the OBS softkey again to return to normal
operation.
Figure 2-25 GPS INTEG, GPS SUSP, NAV1 and NAV2