User manual

3
If necessary, select an option:
• Select Spell Search to search using the name of the
waypoint.
• Select Search Near to search near a recently found
location, another waypoint, your current location, or a
point on the map.
• Select Sort to view the list of waypoints based on nearest
distance or alphabetical order.
4
Select a waypoint from the list.
Editing a Waypoint
1
From the home screen, select Waypoint Manager.
2
Select a saved waypoint.
3
Select an item to edit, such as the name.
4
Enter the new information, and select Done.
Deleting a Waypoint
1
From the home screen, select Waypoint Manager.
2
Select a waypoint.
3
Select > Delete.
Sending a Waypoint
You can send a saved waypoint to other Rino users.
1
From the home screen, select Waypoint Manager.
2
Select a waypoint.
3
Select > Send Location.
Increasing the Accuracy of a Waypoint
Location
You can refine the accuracy of a waypoint location by averaging
the location data. When averaging, the device takes several
GPS readings at the same location and uses the average value
to provide more accuracy.
1
Select Waypoint Manager.
2
Select a waypoint.
3
Select > Average Location.
4
Move to the waypoint location.
5
Select Start.
6
Follow the on-screen instructions.
7
When the confidence status bar reaches 100%, select Save.
For best results, collect four to eight samples for the waypoint,
waiting at least 90 minutes between samples.
Projecting a Waypoint
You can save a new waypoint by projecting the distance and
bearing from a saved waypoint to a new location.
For example, if you would like to navigate to a location you
observe on the other side of a river or stream, you can project a
waypoint from your current location to the observed location,
then navigate to the new location after crossing the river or
stream at a more suitable location.
1
From the home screen, select Waypoint Manager.
2
Select a waypoint.
3
Select > Project Waypoint.
4
Enter the bearing, and select Done.
5
Select a unit of measure.
6
Enter the distance, and select Done.
7
Select Save.
Routes
A route is a sequence of waypoints or locations that leads you to
your final destination.
Creating a Route Using Route Planner
A route can include many waypoints, and it should include at
least a starting point and one destination.
1
From the home screen, select Route Planner > Create
Route > Select First Point.
2
Select a category.
3
Select the first point in the route.
4
Select Use.
5
Select Select Next Point to add additional points to the
route.
6
Select to save the route.
Creating a Route Using the Map
1
From the home screen, select Route Planner > Create
Route > Select First Point > Use Map.
2
Use the Thumb Stick controller to select a point on the map.
3
Press the Thumb Stick controller to select Use.
4
Move the map, and select additional points on the map to
add to the route (optional).
5
Select .
Editing the Name of a Route
You can customize the name of a route to make it distinct.
1
From the home screen, select Route Planner.
2
Select a route.
3
Select Change Name.
4
Enter the new name.
Editing a Route
You can add, remove, or rearrange points on a route.
1
From the home screen, select Route Planner.
2
Select a route.
3
Select Edit Route.
4
Select a point.
5
Select an option:
• To view the point on the map, select Review.
• To change the order of the points on the route, select
Move Up or Move Down.
• To insert an additional point on the route, select Insert.
The additional point is inserted before the point you are
editing.
• To remove the point from the route, select Remove.
6
Select to save the route.
Viewing a Route on the Map
1
From the home screen, select Route Planner.
2
Select a route.
3
Select View Map.
Deleting a Route
1
From the home screen, select Route Planner.
2
Select a route.
3
Select Delete Route.
Routes 5