GSD 22 Sounder Module installation instructions
© Copyright 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Tel. (913) 397.8200 or (800) 800.1020 Fax (913) 397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, UK Tel. +44 (0) 870.8501241 (outside the UK) 0808 2380000 (within the UK) Fax +44 (0) 870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax 886/2.2642.9099 All rights reserved.
INTRODUCTION INTRODUCTION Thank you for choosing the Garmin GSD 22 Sounder Module. The GSD 22 is a CANetTM and Garmin Marine Network compatible, remote sounder module designed to include powerful features found in other Garmin sounders, including Color Depth Control Gain (DCG®), DynacolorTM, and auto gain features technology. When used with compatible Garmin chartplotters, it provides full-featured depth sounder functions.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS The GSD 22 must be properly installed according to the following CANet or Marine Network installation instructions to get the best possible performance. Refer to your chartplotter to determine the correct installation method. To complete the installation, you need appropriate fasteners. If you experience difficulty with the installation, contact Garmin Product Support.
To Sounder GSD 22 Sonar Module White White Green CANet Terminator Connection CANet Terminator Green 3 wire connector To Chartplotter BATTERY 10-35 VOLTS DC CANet Unit CANet Terminator CANet Unit Multiple CANet Unit Connection FUSE 3A The CANet Extension Cable can be cut to any length 1 ft to 80 ft and a CANet compatible device can be inserted on the cable at any point between the two CANet Terminators. RED BLACK GSD 22 SOUNDER MODULE CANet Terminator CANet Unit 1.
INSTALLATION INSTRUCTIONS Marine Network Wiring and Cables Garmin Marine Network components use specialized Garmin Network cables. For some installations, it may be necessary to drill 1.25" (31.7 mm) holes to route the connector end of the cables. Garmin rubber grommets are provided to cover the installation holes (see below). Wiring instructions are found on the following pages.
INSTALLATION INSTRUCTIONS The following diagrams shows the Garmin Marine Network with a GSD 22 Sounder Module connected.
INSTALLATION INSTRUCTIONS Blink Codes When the unit is installed, it switches on when the display unit is powered on (or the GSD 22 remote power line is pulled low, with power applied). The two-color (Green/Red) LED on the GSD 22 indicates the current operational status of the module.
INSTALLATION INSTRUCTIONS SPECIFICATIONS Physical Size: 7.60" L x 6.10" W x 3.00" H (19.3 cm x 5.5 cm x 7.6 cm) Weight: 2.1 lbs. (.953 Kg) Case: Fully gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 529-IPX-7 Temp Range: 5°F to 158°F (-15°C to 70°C) Electrical Source: 10-35 Vdc Usage: 25 watts max. Fuse: AGC/3AG - 3.0 Amp Steering Compass Safe Distance: 5.9" (15.00 cm) Sonar Sounder Power: 500/1,000/2,000 watts (RMS) (Dependent on transducer type.
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. © 2006 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, USA Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, UK Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00579-00 Rev.
