GPSMAP 192C ® chartplotting receiver owner’s manual
© Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax 913/397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Tel. 44/0870.8501241 Fax 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax 886/2.2642.9099 All rights reserved.
INTRODUCTION > ABOUT THIS MANUAL INTRODUCTION Thank you for choosing the Garmin® GPSMAP® 192C. The GPSMAP 192C utilizes the proven performance of Garmin GPS and full-featured BlueChart® coverage of the entire U S coastline. Please take a moment now to compare the contents of this package with the packing list on the outside of the box. If any pieces are missing, contact your Garmin dealer immediately.
INTRODUCTION > TABLE OF CONTENTS Table of Contents Introduction...........................................................................i About This Manual ................................................................... i Care Information..................................................................... iv Basic Operation ...................................................................1 Initializing the Receiver .......................................................... 1 Simulator Mode ....
INTRODUCTION > TABLE OF CONTENTS Time Tab ................................................................................. 62 Pages Tab ............................................................................... 63 Map Tab .................................................................................. 64 General Tab ................................................................................... 64 Source Tab ...................................................................................
INTRODUCTION > CARE INFORMATION Care Information Cleaning the Unit The GPSMAP 192C is constructed of high quality materials and does not require user maintenance other than cleaning. Clean the unit using a cloth dampened with a mild detergent solution and then wipe dry. Avoid chemical cleaners and solvents that can damage plastic components. Storing the GPSMAP 192C Immersing the Unit in Water The GPSMAP 192C is waterproof to IEC Standard 60529 IPX7.
BASIC OPERATION > INITIALIZING THE RECEIVER BASIC OPERATION Initializing the Receiver The first time you turn on the GPSMAP 192C, the receiver must be given an opportunity to collect satellite data and establish its present location. To ensure proper initialization, the GPSMAP 192C is shipped from the factory in AutoLocate mode. Before you initialize, make sure the GPSMAP 192C unit and antenna have been correctly installed on your vessel according to the instructions in the Appendix.
BASIC OPERATION > INITIALIZING THE RECEIVER To graphically initialize the GPSMAP 192C: 1. Press MENU twice for the Main Menu. Press Up or Down on the ROCKER until the GPS tab is highlighted, then press MENU one time. 2. Using the ROCKER, highlight Initialize Position, and press ENTER. The Initialize Position page appears, prompting you to select your approximate location with the map pointer. 3. Use the ROCKER to move the map pointer to your approximate location within 200 miles.
BASIC OPERATION > SIMULATOR MODE Simulator Mode Simulator Mode turns the GPS receiver off for use indoors or practice. Any of the functions discussed in the following pages can be performed in Simulator Mode. While in Simulator Mode, a “Running Simulator” message appears after 2 minutes of inactivity. Keep in mind that the GPSMAP 192C does not track satellites in Simulator Mode, and this mode should never be used for actual navigation.
BASIC OPERATION > ADJUSTING THE BACKLIGHT To adjust the simulated speed and heading from the Pointer or Highway pages: The Set Position, Track Control, Track and Speed fields only show while in Simulator Mode. 1. Press Up on the ROCKER increase the speed in 10 knot/kph/mph increments. Press Down on the ROCKER to decrease the speed in the same increments. 2. Press Left and Right on the ROCKER to steer the boat.
BASIC OPERATION > INTERFACE KEYS Interface Keys POWER Key • Press and hold to turn unit On/Off. • Press and release to adjust backlighting. PAGE Key • Press to cycle through the Main pages. • Press to end an operation in progress and return to the main page. QUIT Key • Press and release to cancel data entry or exit a page. ENTER/MARK Key • Press and release to enter highlighted options and data or confirm on-screen messages. • Press and hold at any time to mark your current location as a waypoint.
BASIC OPERATION > ENTERING DATA AND SELECTING OPTIONS Entering Data and Selecting Options You can select and activate options, and enter data to customize the GPSMAP 192C to fit your requirements. Use the ENTER key and the ROCKER to select options, enter names and numbers in data fields, and activate your selections. To select and activate a function button: Some pages contain function buttons. As shown below, the New Waypoint page has three function buttons: Map, Delete, and OK.
BASIC OPERATION > USING THE MAP POINTER Using the Map Pointer To Pan the Map: Working from the Map page is a simple process that centers around the use of the pointer. Controlled by the ROCKER, the pointer is an important tool that can be used to pan to other map locations, mark and edit waypoints and routes, and review position data of on-screen map items and waypoints. 1. Use the IN/OUT keys to select a map scale. 2. Use the ROCKER to move the pointer.
BASIC OPERATION > CREATING AND USING WAYPOINTS Creating and Using Waypoints The GPSMAP 192C stores up to 3,000 alphanumeric waypoints with a user-defined symbol, comments, and depth available for each waypoint. Waypoints can be created using two basic methods. ENTER/MARK Key—marks your present location, and provides options to select a map position or map item from the map display. You can also enter a new waypoint’s location coordinates manually.
BASIC OPERATION > CREATING AND USING WAYPOINTS 5. To enter optional comments or a depth, highlight the Comments or Depth field to the right of the location coordinates and press ENTER/MARK, use the ROCKER to enter a value, and press ENTER/MARK. 6. To manually enter a set of coordinates, highlight the coordinates and press ENTER/MARK, use the ROCKER to enter the new coordinates, and press ENTER/MARK when finished. 7.
BASIC OPERATION > MAN OVERBOARD (MOB) Man OverBoard (MOB) The GPSMAP 192C’s Man OverBoard function (MOB) simultaneously marks and sets a course to a location for quick response to emergency situations. When a MOB has been activated, a MOB waypoint with an international MOB symbol is created and the unit is on an active navigation to that point. Use any of the Navigation pages to guide you back to the MOB point.
BASIC OPERATION > REVIEWING AND EDITING WAYPOINTS Reviewing and Editing Waypoints When you have created and stored a waypoint, it can be reviewed, modified, renamed, moved, or deleted at any time through the Waypoint Edit page. The Waypoint Edit page is available for any stored waypoint by selecting the waypoint on the map, or selecting it from the waypoint lists under the Points tab in the Main Menu. Submenu Tabs 3.
BASIC OPERATION > NAVIGATING TO A DESTINATION To change the waypoint symbol: 1. Highlight the waypoint symbol field to the left of the waypoint name, and press ENTER. 2. Use the ROCKER to select a new symbol and press ENTER. To change the Comment, Location, Coordinates, or Depth: 1. Highlight the field, and press ENTER. 2. Use the ROCKER to edit/enter the data. To move to the next line, press Right on the ROCKER. 3. Press ENTER when finished.
BASIC OPERATION > NAVIGATING TO A DESTINATION To activate a Go To from a point list: 1. Press the NAV key. Highlight Go To Point and press ENTER. 2. From the Find menu, highlight Waypoints and press ENTER. (You can also choose to go to other points, such as Cities or Tide Stations from this list.) 3. To select a waypoint from the waypoint lists, use the ROCKER to highlight either the By Name or Nearest tab, select a waypoint, and press ENTER.
BASIC OPERATION > NAVIGATING TO A DESTINATION To Go To a new map point (non-map item): 1. Use the ROCKER to move the map pointer to a location. 2. Press NAV. 3. With Go To MAP Point highlighted, press ENTER. TracBack Navigation (Navigating a Track) The TracBack function allows you to retrace your path using the track log automatically stored in the receiver’s memory. This feature eliminates the need to store waypoints along the way.
BASIC OPERATION > NAVIGATING TO A DESTINATION To clear the track log and define a starting point for a TracBack route: 1. Press MENU twice to display the Main Menu page. 2. Using the ROCKER, highlight the Track tab, then highlight the Active tab to the right. 3. Use the ROCKER to select the Erase option, and press ENTER. 4. Highlight the OK field, and press ENTER. You must first save the track log before you can use the Follow Track feature.
BASIC OPERATION > NAVIGATING TO A DESTINATION To activate a TracBack using the NAV key: 1. Press NAV, highlight the Follow Track option, and press ENTER. 2. Highlight the track you want to follow, and press ENTER. 3. Choose Original, to navigate from the start to the end of your trip, or Reverse, to navigate from the end to the start of your trip, and press ENTER. 4. To stop TracBack navigation, press NAV, highlight Stop Navigation, and press ENTER.
BASIC OPERATION > ROUTES Routes To create a route using the Route Edit Map page: The last way to navigate to a destination is to create a user-defined route. The GPSMAP 192C allows you to create and store up to 50 reversible routes (numbered 1-50), with up to 254 waypoints each. Routes can be created and modified in two ways. The first method is to create the route using a map page. This method allows you to select points on the map and see each route leg as it is created.
BASIC OPERATION > ROUTES 7. When finished, press QUIT twice to return to the Route List page. Highlight Edit as Text, and press ENTER to return to the Route Review page. To create a route using text on the Route Review page: 1. Press MENU twice to display the Main Menu page. 2. Use the ROCKER to highlight the Route tab and press MENU to display the route options page, or highlight the first available blank route slot, and press ENTER. (Skip to step 4 if you use this method.) 3.
BASIC OPERATION > FIND 6. From the Find menu, highlight Waypoints, and press ENTER. You can also choose from other points, such as Cities or Tide Stations from this list. From either the By Name or Nearest tab lists, choose the waypoint you want and press ENTER. (See page 50 for searching for waypoints by name.) 7. From the Waypoint Review page, OK is automatically highlighted.
BASIC OPERATION > FIND To Find an item from your current location: 1. From any page, press FIND. 2. Using the ROCKER, highlight the category from the list, and press ENTER. 3. For Waypoints and Cities, search using By Name or Nearest. Use the ROCKER to highlight a sub tab. For By Name, use the top field to spell out the name or scroll down through the list. (See also page 8 for steps on entering a name.) To Find an item from other locations: 1.
BASIC OPERATION > ADDITIONAL INFORMATION To Find an item using the Find options: 1 From any page, press FIND. 2. Using the ROCKER, highlight a category from the list, and press ENTER. 3 From the search results list, press MENU, highlight the an option, and press ENTER. Additional Information Items located using the Find feature have information about the point available. The information varies depending on the type of data loaded on the optional data card.
BASIC OPERATION > DSC DSC The DSC page of the Main Menu allows you to control and set up the Digital Selective Calling (DSC) features on the GPSMAP 192C. Digital Selective Calling (DSC) uses marine VHF radio and Global Positioning System (GPS) technologies to transmit and receive location information. The chartplotter repeats the call properties received from the VHF radio on the chartplotter.
BASIC OPERATION > DSC Understanding Position Reports A Position Report is similar to a Distress Call except no alarm is sounded. Position Reports are not broadcast to all DSC users and are shown with a boat symbol. Receiving DSC Calls Each time you receive a Distress Call or Position Report, a Notification page is displayed, and the call is placed in the DSC Call List and Log.
BASIC OPERATION > DSC DSC Call List The DSC Call List displays the 50 most recent calls, even if the unit is left unattended. The Call List displays the most recent call from a vessel. If a second call is received from the same vessel, it replaces the first call in the Call List. Press MENU to sort the list and delete entries. DSC Log When DSC calls are received, they are automatically placed in the Log, with the most recent call at the top. The unit can log up to 100 calls.
BASIC OPERATION > DSC Navigating to a Position Report or Distress Call After a Position Report or a Distress Call is received, navigation can be quickly set to the call location. To navigate to Position Report or Distress Call: 1 Press the NAV key. 2. With Go To (MMSI/Name) highlighted, press ENTER. Or 1. Highlight the call on the Call List or Log, and press NAV. Setting up DSC The DSC Setup tab allows you to turn DSC On and Off.
MAIN PAGES > OVERVIEW MAIN PAGES There are five main display pages that are always available: Map page, Pointer page, Numbers page, Highway page, and Active Route page. You can cycle through these pages by pressing either PAGE or QUIT. If you have an external Sonar Module with transducer connected to the GPSMAP 192C, a Sonar page is inserted between the Map page and Pointer page. For more information on the Sonar page, please refer to the “Using Sonar” section on pages 78.
MAIN PAGES > MAP PAGE Map Page The GPSMAP 192C’s Map page provides a comprehensive display of electronic cartography, plotting, and navigational data. When in the BlueChart data coverage area or using optional MapSource software, the map display shows your boat on a digital chart, complete with geographic names, map items, navaids, and a host of other chart features. It also plots your track and displays any routes and waypoints you create.
MAIN PAGES > MAP PAGE Using the Map Pointer The pointer pans away from your present location (even outside of your current detail coverage.) As you pan past the edge of the current map display, the screen actively scrolls forward to provide continuous map coverage. An hourglass symbol appears by the pointer while the unit is busy drawing new map details. Additional Information Tabs Pressing ENTER while highlighting a map item brings up additional details and options.
MAIN PAGES > MAP PAGE Use the pointer to create new waypoints directly from the map. To create a waypoint with the pointer: 1. Use the ROCKER to move the pointer to the map location. 2. Press ENTER and the New Map Waypoint window appears. If the pointer is on a map item, you get a new window with details about the item when ENTER is pressed. Press ENTER again on the highlighted Create Wpt option. 3. Press ENTER to confirm the new waypoint using the default three-digit name and symbol.
MAIN PAGES > MAP PAGE The GPSMAP 192C’s system has a built-in worldwide database to 20 mi, with more detailed coverage available through the use of the BlueChart or MapSource data. The GPSMAP 192C displays cartography as long as there is chart information available for the range you have selected. Map coverage conforms to the following conditions: • When the selected zoom range is covered by the internal database, BlueChart, or MapSource data, cartography is displayed.
MAIN PAGES > MAP PAGE Change Numbers—specifies the type of data displayed in each data field used on the map display. To change a data field: 1. From the menu, use the ROCKER to highlight the Change Numbers option, and press ENTER. 2. Move the field highlight to the data field you want to change and press ENTER. 3. Move up or down on the list using the ROCKER to highlight the data you want to display, and press ENTER. To exit, press QUIT.
MAIN PAGES > MAP PAGE You can also choose to merge the four medium default data fields to a single, large field for better readability or you can split any or all of the default data fields to show four small data fields. 3. Move the pointer to the end measurement point. The bearing and distance from the reference point and pointer coordinates is displayed in the data window at the top of the display. Press QUIT to finish.
MAIN PAGES > POINTER PAGE Set Up Map—configures the map display preferences, including map detail, map orientation, automatic zoom, and various map items and points. Please refer to “Main Menu Map Tab” on page 64 for more information. • Defaults—restores settings back to factory settings for the tab highlighted. • All Map Defaults—restores settings back to factory settings for all tabs. To change a map setup feature: 1. From the Map page menu, highlight Set Up Map, and press ENTER. 2.
MAIN PAGES > NUMBERS PAGE Current Go To Destination Data Fields Bearing Bug Bearing Pointer Compass Ring The GPSMAP 192C’s Pointer page features a menu page that provides access to layout and data field options. The data window, located at the top of the page, provides a user-selectable layout of various types of useful data. Each data field can be configured to display several data options. The data window layout can be configured to display additional data fields and change the size of the data displayed.
MAIN PAGES > HIGHWAY PAGE Highway Page Numbers Page shown with middle data field split into four fields The GPSMAP 192C’s Highway page provides graphic steering guidance to a destination waypoint, placing greater emphasis on your straight-line course, and the distance and direction you are off course. As you head toward your destination, the middle of the screen provides visual guidance to your waypoint on a moving graphic highway. Your present location is at the bottom center of the highway display.
MAIN PAGES > HIGHWAY PAGE The four data fields at the top of the page provide additional userselectable guidance information. Additionally, a compass ribbon is displayed to show your current heading along with a dark, vertical bar that indicates the direct bearing to the navigation point. When the dark, vertical indicator (or arrow) lines up with the lighter red bar in the middle, you are heading directly to the navigation point.
MAIN PAGES > ACTIVE ROUTE PAGE Active Route Page Check or uncheck the options you want to show/not show on the Highway page. The Active Route page shows each point of the active route, with the point name, distance and choice of Course, ETA, Fuel, Leg Distance, Leg Fuel, Leg Time, Sunrise, Sunset, or Time To for each point from your present location. The current destination point is marked with an arrow icon.
MAIN PAGES > ACTIVE ROUTE PAGE Active Route Page Options The following options are available from the Active Route page: • Hide/Show Numbers—see page 31 for instructions (same as Map page option). • Change Numbers—see page 31 for instructions. • Edit on Map—see page 17 for instructions. • Add Before—see pages 17 for instructions. • Remove—see pages 17 for instructions. • Invert—reverses the direction of the route. • Re-evaluate—recalculates and reactivates the current route. • Invert—reverses the route.
MAIN MENU > GPS TAB MAIN MENU The GPSMAP 192C’s Main Menu page provides access to various waypoint, system, navigation, interface management, and setup menus. The 19 Menu tabs are divided into categories by function. The Main Menu page is available from any page in the system, and is accessed by pressing MENU twice. See pages 6 for additional instructions on changing settings and entering data. Sub Tabs To select a Menu tab from the Main Menu Page: 1. Press Up or Down on the ROCKER to highlight a tab.
MAIN MENU > GPS TAB • No signal strength bars—the receiver is looking for the satellites indicated. • Light signal strength bars—the receiver has found the satellite(s) and is collecting data. • Dark signal strength bars—the receiver has collected the necessary data and the satellite(s) are ready for use.
MAIN MENU > GPS TAB WAAS satellites are numbered 33 or higher when viewing the sky view on your GPSMAP 192C. Initial reception of the WAAS signal can take up to 15-20 minutes, then 1-2 minutes afterwards. When WAAS differential correction has been received for GPS satellites (numbers 32 or below), a D appears in the signal bar of the sky view and 2D or 3D Differential appears in the receiver status.
MAIN MENU > GPS TAB • AutoLocate—the receiver is looking for any satellite whose almanac has been collected. This process can take up to five minutes. • Acquiring Satellites—the receiver is looking for and collecting data from satellites visible at its last known or initialized position, but has not collected enough data to calculate a fix. • 2D—at least three satellites with good geometry have been acquired and a 2 dimensional position fix (latitude and longitude) is being calculated.
MAIN MENU > TIDE TAB GPS Tab Options The GPS tab features an options page that provides access to functions and features relating to the GPS Info display. To display and select the GPS Tab options: Tide Tab The Tide tab shows a graphical chart that displays tide station information in a 24 hour span starting at midnight station time. You can choose from different dates and more than 3,000 tide stations. 1. Press MENU. 2. Using the ROCKER, highlight an option, and press ENTER.
MAIN MENU > TIDE TAB are in 4-hour increments, and the light, dotted vertical lines are in 1-hour increments. A solid, vertical line (with the current time box at the top) indicates the time of day when using current date and intersects the tide graph to show their relation. You can select from a list of nearest stations. The tide curve shows as a shaded area, with higher tides being taller (blue) and lower tides shorter (red).
MAIN MENU > TIDE TAB Automatically search for the nearest station using a variety of search locations. You must select a location within 100 nm of a tide station. If you are not within this range, you see a message “None Found.” Use the Nearest To Other Find option and select a location closer to a tide station. To select a tide station from the map: 1. When the search results appear, press FIND, highlight Tide Stations, press ENTER, and then press MENU. 2. Highlight Nearest To Other, and press ENTER. 3.
MAIN MENU > TRIP TAB Move the time bar on the tide chart in 5 minute increments to show tide heights at various times on the chart. To see tide heights at various times on the chart: 1. Press MENU, highlight Move Cursor, and press ENTER. 2. Press Left or Right on the ROCKER to change the time. Press QUIT when finished or press MENU, highlight Stop Moving Cursor, and press ENTER.
MAIN MENU > CELES TAB Celes (Celestial) Tab To choose a position: The Celestial tab displays celestial data for sun and moon rise/set, moon phase, and approximate skyview location of the sun and moon. The moon phase displays the current visible portion of the moon as a light color. You can display this data for your current location, a location from the map, or a Find item location. Use the current data, or select a different date and time.
MAIN MENU > POINTS TAB Points Tab The Main Menu Points tab features two waypoint sub tabs, User and Proximity, that allow you manage a large number of waypoints quickly and efficiently. The sub tabs also provide a continuously updated proximity waypoint alarm function that can be used to define an alarm circle around items such as submerged hazards or shallow waters. Sub Tabs Celestial Tab Menu To change the time or date: 1.
MAIN MENU > POINTS TAB To select the Points (Waypoint) sub tab: 1. Use the ROCKER to highlight the Points menu tab. A list of stored waypoints appear to the right of the Main Menu list. 2. Press Right one time on the ROCKER. The User tab is now highlighted. 3. Press down on the ROCKER until a waypoint is highlighted. User Waypoint List The first waypoint sub tab list available from the Points tab is the User list, that displays a master list of all waypoints currently stored in memory.
MAIN MENU > POINTS TAB To display the waypoint menu options: Using the ROCKER, highlight the User tab, and press MENU. To scroll through and review the waypoint list: 1. With the ROCKER, highlight the Points tab from the main menu page and then highlight User. 2. Use the ROCKER to scroll through the list. 3. Press ENTER to review the highlighted waypoint on the Waypoint Edit page. 4. Press ENTER to return to the list and automatically highlight the next waypoint.
MAIN MENU > POINTS TAB To delete waypoints by symbol: 1. From the User sub tab, highlight the waypoint to delete, and press MENU. Select Delete By Symbol, and press ENTER. 2. Use the ROCKER to highlight the symbol of the waypoint(s) to delete, and press ENTER. 3. Press ENTER to confirm. To stop the deletion, choose Cancel, or press QUIT. To delete all waypoints or the entire waypoint list: 1. Press MENU to select the options window. 2. Use the ROCKER to highlight Delete All, and press ENTER. 3.
MAIN MENU > POINTS TAB To add a proximity waypoint: 1. Use the ROCKER to highlight an empty space on the Proximity list, and press ENTER. The Find screen appears. Highlight Waypoints, and press ENTER. 2. To select a waypoint from the lists, use the ROCKER to highlight a waypoint from the User or Nearest tab. To select a waypoint from the map, highlight either the User or Nearest tab, and press MENU. With Select From Map highlighted, press ENTER.
MAIN MENU > ROUTES TAB Routes Tab The GPSMAP 192C Route List page displays all the routes currently stored in memory, along with a descriptive name for each route. When a route has been created, it can be activated and used for navigation with the NAV key. A route can be followed in the same sequence as it was originally created, or you can invert the route and navigate from the end waypoint back to the beginning waypoint.
MAIN MENU > ROUTES TAB Route Review Page Route Name When you have created a route, the Route Review page allows you to review and modify the route displayed. Data Fields To display the Route Review page: 1. Press MENU twice, highlight the Route tab. 2. Highlight the route you want to review, and press ENTER. Route Points Data Totals The Route Review page also allows you to enter your own 15character name for any listed route. By default, the name includes the first and last waypoints in the route.
MAIN MENU > ROUTES TAB When you are on the Route Review page, you can review the route points (waypoints or map items) one at a time from the list. To review individual route points: Route Review Menu Options Menu options available from the Route Review page are Edit on Map, Add Before, Remove, and Trip Planning. 1. Highlight a point, and press ENTER. 2.
MAIN MENU > ROUTES TAB Edit on Map—allows you to review and modify the route displayed for each point (waypoint or map item) on a map page. Use the pointer to insert a new route point on a route leg, review the waypoint, or map item. To edit the route on the map: From the Route Review page, press MENU, highlight Edit on Map, and press ENTER. To edit a route point: Use the ROCKER to highlight a route waypoint, and press MENU. To review a route point: Highlight the point, and press ENTER.
MAIN MENU > ROUTES TAB Add Before—inserts a waypoint into the list of route points or add a point(s) onto the end of the route. To insert a point into the route, or add a point to the end: 1. From either the Route Review or Active Route pages, use the ROCKER to highlight the point you want to insert the new point before (to add a point to the end, highlight the blank field at the bottom of the list), and press MENU. 2. Highlight Add Before, and press ENTER. 3.
MAIN MENU > ROUTES TAB Trip Planning—the Route Review and Active Route pages also display trip-planning information for each leg or the entire route. Available information includes Course, ETA, Fuel (to point), Leg Distance, Leg Fuel, Leg Time, Sunrise and Sunset (at point location), and Time To (point). Trip Planning Data Fields To use the Trip Planning feature: 1. To select a planning field, highlight a route from the Route List, and press ENTER to display the Route Review page. 2.
MAIN MENU > TRACK TAB Track Tab The Track tab allows you specify whether or not to record a track log, define how it is recorded, or save track log data for future use. The Track Logs page also provides an indicator of the memory used for the active track log and options to clear the track memory or start a TracBack route. See pages 14 for TracBack information. The Track submenu is divided in two sub tabs: Active tab and Saved tab.
MAIN MENU > TRACK TAB For the Active tab, the following settings are available: • Record Mode—contains three track recording options: Off—the track log is not recorded. Selecting the Off setting prevents you from using the TracBack feature. Fill—a track log is recorded until the track memory is full. Wrap—records the track log is continuously recorded, wrapping through the available memory (replacing the oldest track data with new data). • Interval—defines the frequency the track plots are recorded.
MAIN MENU > DSC TAB You can use the Review On Map option to display a saved track on a Track Map page. To activate a TracBack from the Saved tab list: 1. Using the ROCKER, highlight a track, and press NAV. 2. The Follow
MAIN MENU > CARD AND TIME TABS Card Tab The Card tab contains options for saving waypoints, routes and tracks to a data card. When data is saved to a data card, it can be exchanged with other compatible units and Garmin’s MapSource PC program. To transfer data to/from a data card: 1. Insert the data card. From the Card tab, select the check box next to each type of item you want to transfer. 2. Highlight Save To Card, and press ENTER to save the selected items to the data card. 3.
MAIN MENU > PAGES TAB Pages Tab The Pages tab allows you to turn on/off any of the main pages or Jump To a particular page. You can also set the page that appears first when you turn on the unit or enable/disable the GPS Info on the initial screen. To select/deselect a main page: Use the ROCKER to highlight the box to the left of the page name. Pressing ENTER selects/deselects that page. When a page is selected a check mark appears in the box. You must leave at least one page checked.
MAIN MENU > MAP TAB Map Tab The Map tab changes the display properties of the Map page. The following pages contain descriptions of the Map tab’s eight sub tabs. General Tab • Detail—Most, More, Normal, Less, Least: controls how much map detail is displayed. This setting only applies to map features set to Auto. Features that have a specified scale or are turned Off are unaffected by this setting. • Orientation—North Up: fixes the top of the map display to a north heading.
MAIN MENU > MAP TAB To display the Map Information page: 1. Highlight the Detail option box, and press ENTER. 2. Use the ROCKER to scroll through the list of maps. 3. To select/deselect a map, highlight the check box to the left of the name of a map. Press ENTER to select/deselect the map. The map is selected and is displayed on the Map page when a check mark appears in the box adjacent to that map. 4. To display detailed information and notes for each area, highlight a name and press ENTER.
MAIN MENU > MAP TAB Points Tab The Spot Soundings, Tide Stations, and Services options each contain adjustments for Text and Zoom. • Text—None (except Spot Snd.), Small, Medium, and Large: controls the screen size of the name. • Zoom—Auto, Off, 120 ft-800 mi: sets the maximum scale features should appear on the Map page. Some types of data only show up to specific zoom scales. 66 Navaids Tab • Symbol Set—Auto, Garmin, NOAA, International: controls the navaid symbol set.
MAIN MENU > MAP TAB Nav Line Tab • Heading Line—On/Off: draws an extension from the end of the boat icon in the direction of travel. • Bearing Line—On/Off: toggles the black/white line that points to the current navigation point. • Course Line—Auto, Off, 120 ft-800 mi: sets the maximum zoom scale the course line appears on the screen. Track Tab Other Tab • Accuracy Circle—On/Off: toggles the circle On and Off.
MAIN MENU > HIWAY, TEMP, AND SONAR TABS Hiway (Highway) Tab The Highway tab contains display settings for the Highway page. Please refer to the “Highway Page” section on page 35. Temp (Temperature) Tab Sonar Tab The Sonar tab contains setup options for the Sonar page. The Sonar page is not active if you do not have an external Sonar Module with transducer. Please refer to the “Using Sonar” section on page 78 for more information on sonar setup options.
MAIN MENU > SYSTM TAB Systm (System) Tab The System tab controls system setting for beeper, speed filter, languages, system mode, and simulator controls, restores factory settings, displays software version, and prepares software update cards. The following settings are available: • Beeper—Off, Alarms Only, Key and Alarm: controls audible beeps for keys and alarms. • Speed Filter—Off, Auto, On: averages speed-readings. • Language—displays the on-screen display languages.
MAIN MENU > UNITS TAB Units Tab The Unit tab defines the Position Format, Map Datum, Heading, Distance, Speed, Elevation, Depth, and Temperature units. The following settings are available: • Position Format—changes the coordinate system. You should only change the position format if you are using a map or chart that specifies a different position format or want to use a format you are familiar with. For additional information on Loran TD setup, see pages 108.
MAIN MENU > UNITS TAB • Heading—selects the reference used in calculating heading information. You can select from Auto Mag Var, True, Grid, and User Mag Var. Auto Mag Var provides magnetic north heading references that are automatically determined from your current location. True provides headings based on a true north reference. Grid provides headings based on a grid north reference (and is used in conjunction with the grid position formats described on page 70).
MAIN MENU > COMM TAB Comm (Communications) Tab The Communications tab controls the input/output format used when connecting your GPSMAP 192C to external NMEA devices, such as an external Sonar Module, a DGPS beacon receiver, a personal computer, or another Garmin unit. NOTE: If a DGPS receiver is used, WAAS capability is automatically turned to Off. See page 99 for wiring and NMEA version information. The unit supports two input/output ports.
MAIN MENU > COMM TAB To select a transfer mode: 1. Use the ROCKER to select Garmin Data Transfer in the Serial Data Format field. 2. Highlight the Transfer Mode field, and press ENTER. 3. Use the ROCKER to select the setting, and press ENTER. Advanced NMEA settings to adjust the NMEA output are available if you have one of the ports set to NMEA In/NMEA. Advanced NMEA settings enable/disable certain sentences and adjust the number of Lat/Lon output precision digits.
MAIN MENU > COMM TAB To adjust the NMEA output: 1. From the Comm tab, press MENU, highlight NMEA Setup, and press ENTER. 2. Highlight an option, and press ENTER. 3. Use the ROCKER to select the setting, and press ENTER. Press QUIT to return to the Comm tab. To restore the Serial Data Format settings back to the default Garmin Data Transfer: From the Comm tab, press MENU, highlight Defaults, and press ENTER.
MAIN MENU > COMM TAB To manually enter a frequency and bit rate: Status Field SNR and Distance shows data when signal is received. 1. With the unit set to Garmin DGPS or RTCM In/NMEA Out, use the ROCKER to highlight the Beacon field, and press ENTER. 2. Highlight User, and press ENTER. 3. Highlight the Frequency or Bit Rate field, press ENTER, enter a frequency or bit rate, and press ENTER when finished. The Status field shows one of the following: NOTE: The DGPS beacon transmitters are operated by the U.S.
MAIN MENU > ALARM TAB Alarm Tab The Alarm tab allows you to define the alarm settings. The Alarm tab is divided into three sub tabs: System alarms, Nav alarms, and Sonar alarms. System Tab • Clock—provides an alarm for the system clock. Enter a time in the time field, and turn the alarm on and off from the control field menu. Remember to enter alarm times in the same time format (UTC or local) you are using for your system. The unit must be on for the clock alarm to work.
MAIN MENU > ALARM TAB To set an alarm: Use the ROCKER to highlight a sub tab. Highlight the field you want activate, and press ENTER. Change the mode to the setting, and press ENTER. Highlight the next field to the right, press ENTER, enter the settings, and press ENTER to finish. 5. If you want the alarm to display and beep until acknowledged, highlight the Persist box, and press ENTER. 1. 2. 3. 4. GPSMAP 192C Owner’s Manual If Persist is checked, an alarm stays active until acknowledged.
USING SONAR > SONAR PAGE USING SONAR This section covers the additional sonar options for the GPSMAP 192C when used in conjunction with a Sounder Module. Read the Installation Instructions to properly install the Sounder Module. NOTE: You MUST have a Sounder Module installed and connected to your GPSMAP 192C to use the sonar features. When a Sonar Module, such as the GSD 20, and a transducer are connected to the GPSMAP 192C, the Sonar page is added to the page sequence.
USING SONAR > SONAR PAGE Using the Adjustment Menu The Adjustment Menu gives you direct access to the settings and features most commonly used on the Sonar page. The option selected currently appears in the upper left of the display. Press MENU and highlight Adjustments to see a list of all options and their current settings. To select an adjustment option from the Sonar page: 1. Press the ROCKER Left/Right to scroll through the options in the upper left of the display. 2.
USING SONAR > SONAR PAGE Zoom Adjustment Range Adjustment Range—sets the display depth range used for viewing. The unit can be set to automatically track the bottom or set to a userspecified depth range. Auto mode displays the most information possible while continuously showing the bottom. Zoom—used to quickly select a display zoom scale or split the display. When a scale other than No Zoom is selected, the Adjustment Menu displays a new selection labeled View.
USING SONAR > SONAR PAGE • Btm (Bottom) Split—shows two reduced pictures; the right at the original depth scale and the left showing sonar returns from the bottom up. All target depths read as a distance from the bottom. • Btm (Bottom) Lock—displays only the Bottom Lock picture (returns from the bottom up) on the full screen. However, if Dual Frequency Display is set to Split, then a 50/200kHz split screen is displayed. When activated, the zoomed picture becomes the Sonar page display.
USING SONAR > SONAR PAGE Target Level—adjusts how dark or light a return (or target) is displayed on-screen. A Color Bar (see page 87) appears on the right side of the screen as you adjust this setting. The higher the percentage, the darker the return appears. This setting does not increase or decrease the unit Gain. Whiteline Adjustment Frequency—allows you to choose a transducer frequency. Frequency refers to the pitch of the sound that the transducer sends and receives.
USING SONAR > SONAR PAGE Scroll—adjusts the rate that the graph scrolls from right to left. If you are sitting still or the graph is moving too fast, slowing the scroll rate or pausing it can be beneficial. Depth Line Adjustment Noise Reject—helps filter unwanted noise from the graph. The Noise Reject tool can be turned Off, set to Normal (automatically adjusts for optimum viewing), or to a fixed 1-100% setting.
USING SONAR > SONAR PAGE Sonar Page Options The GPSMAP 192C’s Sonar page features a menu page that provides access to additional functions and to layout and data field options. To change an Adjustment setting: 1. While on the Adjustment options list, use the ROCKER to highlight the option, and press ENTER. 2. Use the ROCKER to make the change, and press ENTER. Show/Hide Pointer—allows you to reference sonar items and mark underwater waypoints.
USING SONAR > SONAR PAGE To mark an underwater waypoint: 1. From the Sonar page, press MENU, highlight Show Pointer, and press ENTER to pause the screen movement. 2. Use the ROCKER to move the cursor onto the target, such as underwater drop offs and stumps, you want to mark. The data window at the top of the screen displays the cursor’s depth, coordinates, bearing and distance from your current position. 3. Press ENTER/MARK.
USING SONAR > SONAR TAB OPTIONS Double-Arrow Size Split Menu Options Resizing the Split Sonar Display Sonar Tab Options To access and change a setting on the Sonar tab: 1. Press MENU twice to access the Main Menu. Use the ROCKER to highlight the Sonar tab. 2. Using the ROCKER, highlight the field, and press ENTER. 3. Highlight the setting, and press ENTER. 4. Press QUIT to return to the Sonar page or previous page.
USING SONAR > SONAR TAB OPTIONS Depth Number—controls the efficiency of the digital depth update rate. Fast Update updates more quickly and is recommended for low-noise, deeper water (>50 ft) Auto is best for shallow water or high noise areas, and produces a slower screen update. Use Auto when you travel a wide variety of depths. NOTE: If the unit is unable to track the bottom for any reason, the digits in the depth window flash on and off to alert you that the unit is not tracking the bottom.
USING SONAR > SONAR TAB OPTIONS Keel Offset—controls offset the surface reading for the depth of a keel. This makes it possible to measure depth from the bottom of your keel instead of from the transducer’s location. Enter a positive number to offset for a keel, or enter a negative number to compensate for a large vessel that can draw several feet of water. The Keel Offset reflects in the depth reading.
USING SONAR > SONAR TAB OPTIONS To calibrate the water speed: 1. On the Sonar tab, use the ROCKER to highlight Calibrate Water Speed, and press ENTER. 2. Bring the boat to a cruising speed. The top ground and uncalibrated water speeds are shown at the bottom of the calibration window. Note your top water speed, then stop the boat, and press ENTER. 3. By default, the top ground speed automatically displays in the What was your top water speed? field.
USING SONAR > UNDERSTANDING SONAR Understanding Sonar The transducer mounted on your vessel transmits sound waves toward the bottom of a lake, stream, or seabed in a cone-shaped pattern. When a transmitted sound wave strikes an underwater object—such as the bottom, a piece of structure, or a fish—sound is reflected back to the transducer. The transducer collects the reflected sound waves and sends the data to the GPSMAP 192C to be processed and displayed.
USING SONAR > UNDERSTANDING SONAR Transducer Coverage The area covered by the transmitted sound waves is determined by the cone angle of the transducer and the water depth. The wide cone angles (40°) associated with low frequencies (50 kHz) provide a large coverage area for finding fish within a coverage width that is approximately 2/3 of the water depth. However, this also means that wide cone angles produce less bottom detail and resolution.
USING SONAR > UNDERSTANDING SONAR Whiteline The Sounder Module can help you determine whether the bottom is hard or soft. When the sonar sound waves are reflected back by the bottom, a hard bottom returns a stronger signal than a soft bottom. A thin whiteline indicates a softer bottom, while a thick whiteline indicates a harder bottom. Normally, a red line is used to show the point where water meets the bottom. This line follows the bottom contour, along with any significant objects lying on the bottom.
APPENDIX > SPECIFICATIONS APPENDIX Specifications Physical Specifications Size: 6.20" H x 6.30" W x 2.64" D (15.7 cm x 16.0 cm x 6.7 cm) Weight: Less than 2.0 lb Display: 5.0" diagonal (12.7 cm) 16-color TFT display with backlighting (234 x 320 pixels) Case: Fully gasketed, high-impact plastic alloy, waterproof to IEC 529-IPX-7 Temp. Range: 5°F to 158°F (-15°C to 70°C) Performance Receiver: Differential-ready 12 parallel channel WAAS capable receiver Acquisition Times: Warm: Approx.
APPENDIX > INSTALLING THE GPSMAP 192C Installing the GPSMAP 192C The GPSMAP 192C must be properly installed according to the following instructions to get the best possible performance. If you have the GPSMAP 192C with the built-in internal bail mount antenna, you can skip this section and proceed to the next page. For units purchased with the remote antenna, follow the instructions below.
APPENDIX > MOUNTING THE GPSMAP 192C UNIT To install the GPS antenna: 1. Screw the antenna directly onto the 1" x 14-thread mount. 2. Route the cable to the mounting location of the display unit. Use the appropriate tie-wraps, fasteners, and sealant to secure the cable along the route and through any bulkhead or deck. 3. After the GPSMAP 192C unit is installed, connect the cable to the antenna connector on the back of the display unit.
APPENDIX > MOUNTING THE GPSMAP 192C UNIT 5. Screw the two mounting knobs through the bracket and into the display case. 6. Connect the power/data and antenna cables (external antenna only) to the back of the unit, making sure the locking rings are fully tightened on both connectors. The GPSMAP 192C with external antenna can be flush mounted on a flat panel of .08-.52" thickness using the cam lobe feature on its gimbal mounting bracket.
APPENDIX > MOUNTING THE GPSMAP 192C UNIT To flush mount the GPSMAP 192C unit using the gimbal mounting bracket: 1. Cut a 4.33" x 4.33" (110 x 110 mm) hole in the panel. 2. Place the GPSMAP 192C into the hole from the front until the flange rests against the mounting surface. 3. From the back of the panel, loosely attach the bracket so the slot in the ratchet area points away from the mounting panel (figure 1). 4.
APPENDIX > INSTALLING THE FERRITE BEAD CLAMP Installing the Ferrite Bead Clamp In order to filter Radio Frequency Interference (RFI) radiation that could possibly interfere with items such as televisions, radios, or other marine electronics operating in close proximity to the GPSMAP 192C with the remote antenna, a ferrite bead filter clamp and neoprene foam strip are included for attachment to the unit’s antenna cable.
APPENDIX > CONNECTING THE POWER/DATA Connecting the Power/Data The power/data cable connects the GPSMAP 192C to a DC system and provides interface capabilities for connecting external devices. The color code in the diagram below indicates the appropriate harness connections. Replacement fuse is a AGC/3AG - 1.5 Amp fuse. For wiring the GPSMAP to a GSD 20 Sonar Module, refer to the “GSD 20 Installation Guide.
APPENDIX > INSTALLING AND REMOVING DATA CARDS Installing and Removing Data Cards The GPSMAP 192C uses optional Garmin marine BlueChart and MapSource data cards to display digital charts and maps on-screen. Data cards are installed in the card slot located at the bottom right of the unit. Data cards can be installed or removed at any time, whether the unit is on or off. To remove a data card: 1.
APPENDIX > SATELLITE INFORMATION Satellite Information 90° Satellite Strength Indicator Bars Center dot - 90° above the horizon Inner ring- 45° above the horizon Outer ring the horizon 45° Satellite Sky View Satellite Location The location of each available satellite is displayed over two location rings on the Satellite Information page. The outer ring represents the horizon, the inner ring represents 45° above the horizon, and the center represents directly overhead.
APPENDIX > WHAT IS A WAAS AND DGPS? What is WAAS? The Wide Area Augmentation System (WAAS) is an F.A.A. funded project to improve the overall integrity of the GPS signal. It is a space-based system that broadcasts integrity information and correction data as determined by ground reference stations. WAAS testing completed in September of 2003 confirmed an accuracy of 2 to 3 vertical meters throughout the majority of the continental U.S. and portions of Alaska. For more information, go to http://gps.faa.
APPENDIX > WHAT IS MMSI? What is a Maritime Mobile Service Identity (MMSI)? Maritime Mobile Service Identity (MMSI) basically allows a VHF radio to act like a phone. In order to make a “call” on a phone, you first need a phone number to dial. The 9 digit MMSI number acts like a phone number when used in a Position Report and as a unique identifier to the Coast Guard when used in an emergency Distress Call.
APPENDIX > NAVIGATION TERMS Navigation Terms destination or the final waypoint in a route. Avg Speed—The average of all second-by-second speed readings since last reset. ETA at Next—The time you estimate to reach a Goto destination or the next waypoint in a route. Bearing (BRG)—The compass direction from your current location to a destination. Fuel—The fuel required to travel from current location to the indicated route waypoint. Course—The course between the active from and to waypoints.
APPENDIX > NAVIGATION TERMS Speed—The current velocity at which you are travelling, relative to a ground position. Also referred to as ground speed. Sunrise—The current day’s time of sunrise. Sunset—The current day’s time of sunset. Time Of Day—The current time. Time To—The estimated time required to reach a Goto destination, or the next waypoint in a route. Also known as “estimated time en route.” Time to Dest—The estimated time required to reach a Goto destination, or the final waypoint in a route.
APPENDIX > MESSAGES Messages No Diff GPS Location—RTCM is selected but no DGPS data is being received. Arriving at Destination—You are nearing your destination. No Tide Stations for that Area—No tide stations within 100 miles of the area. Approaching Turn—You are nearing a turn in a route. Batteries Low—You have less than 10 minutes of battery left. Can’t Unlock Maps—No applicable unlock code for one or more maps was found.
APPENDIX > MESSAGES Track Already Exists—A saved track with the same name already exists. Track Truncated—A complete uploaded track does not fit in memory. The oldest track log points have been deleted. Track Memory Full—No more track data can be stored without deleting old data. Transfer Complete—Data transfer has been completed. Track Log Full—The track log is full and track recording has been turned off. To record more track points, you need to clear the track log and turn track recording on.
APPENDIX > LORAN TD SYSTEM LORAN TD System LORAN C is a radio navigation aid operated and maintained in the United States by the United States Coast Guard. The name LORAN is an acronym for “LOng RAnge Navigation.” The LORAN system covers the entire United States and the U.S. Coastal Confluence Zone. From the perspective of a mariner, the system is used for ocean and coastal navigation.
APPENDIX > LORAN TD SYSTEM The LORAN Position Format field is located under the Setup– Location tab in the Main Menu. The LORAN TD Setup window contains the fields to select the Loran GRI-Chain Number, Primary and Secondary Stations, and TD Offsets. To set up Loran TD from the Main Menu: 1. Press MENU twice to display the Main Menu. 2. Using the ROCKER, highlight the Position Format field on the Units tab, and press ENTER. 3. Highlight Loran TD and press ENTER. 4. Highlight Setup and press ENTER. 5.
APPENDIX > OPTIONAL ACCESSORIES Optional Accessories The following optional accessories are designed to enhance the operation of the GPSMAP 192C. To obtain replacement parts and optional accessories, contact your Garmin Dealer, Garmin Product Support in the U.S.A. at 800-800-1020, or Garmin Europe at 44-0870-8501241. WARNING: Garmin accessories have been designed and specifically tested for use with Garmin products.
APPENDIX > OPTIONAL ACCESSORIES Software License Agreement Product Registration Garmin grants you a limited license to use the software embedded in this device (the “Software”) in binary executable form in the normal operation of the product. Title, ownership rights, and intellectual property rights in and to the Software remain in Garmin. Use this area to record the serial number (8-digit number located on the back of the box) in case your GPSMAP 192C unit is lost, stolen, or needs service.
APPENDIX > OPTIONAL ACCESSORIES Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase. Within this period, Garmin will at its sole option repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts or labor, provided that the customer shall be responsible for any transportation cost.
APPENDIX > OPTIONAL ACCESSORIES The Garmin GPSMAP 192C has no user-serviceable parts. Should you ever encounter a problem with your unit, please take it to an authorized Garmin dealer for repairs. The GPSMAP 192C is fastened shut with screws. Any attempt to open the case to change or modify the unit in any way will void your warranty and may result in permanent damage to the equipment.
APPENDIX > OPTIONAL ACCESSORIES Safety Information MAP DATA INFORMATION: One of the goals of Garmin is to provide customers with the most complete and accurate cartography that is available to us at a reasonable cost. We use a combination of governmental and private data sources, which we identify as required in product literature and copyright messages displayed to the consumer. Virtually all data sources contain inaccurate or incomplete data to some degree.
INDEX INDEX Symbols 2D Differential 42 2D GPS Location 90, 101 3D Differential 42 3D GPS Location 101 A Accessories 110 Accuracy 39 Accuracy Alarm 76 Accuracy Circle 67 Active Route Page 37 Options 38 Alarms Accuracy 76 Anchor Drag 76 Arrival 76 Battery 76 Clock 76 DGPS 76 DSC 25 Fish 76 Off Course 76 Shallow/Deep Water 76 Temperature 76 Alarm Tab 76 GPSMAP 192C Owner’s Manual Anchor Drag Alarm 76 Arrival Alarm 76 B BackLight 4 Base Map 64 Battery Alarm 76 Bearing Line 67 Bottom Split 81 C Card Tab
INDEX L Language 69 License Agreement 111 LORAN TD 108 M Magnetic Variation 71 Main Menu 39 Main Pages 26 Man OverBoard 10 MapSource 62 Map Data Information 114 Map Datum 70 Map Detail 64 Map Information Page 65 Map Page 27 Options 30 Setup Map 33 Map Pointer 7, 28 Map Scales 29 Map Tab 64 Maritime Mobile Service Identity 103 Mark Key 5 Measure Distance 32 Menu Key 5 Merge From Card 62 Messages 105 MMSI 22, 103 MOB 10 MOB Key 5 116 N NAV/MOB Key 5, 12 Navaids 66 Navigating 12 Distress Call 25 Go To 13
INDEX TracBack 14 Activate 16 Track Logs Clear 15 Save 15 Track Tab 59 Active 59 Saved 59 Track Up 64 Transducer 91 Trip Planning 58 Trip Tab 46 U Underwater Waypoints 85 Units Tab 70 Unit Defaults 69 W WAAS 40, 102 Disable/Enable 41 Waterproof iv Water Speed 88 Water Temperature Alarm 76 GPSMAP 192C Owner’s Manual Waypoints Creating 8 Creating Graphically 9 Editing 11 Enter/Mark 8 Move 12 Proximity 52 Reviewing 11 Underwater 85 Waypoint Lists Proximity 51 User 49 Whiteline 82, 92 Wide Area Augmentati
For the latest free software updates (excluding map data) throughout the life of your Garmin products, visit the Garmin Web site at www.garmin.com. © Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00546-00 Rev.
