GPSMAP 2006/2010 & GPS 17 ® installation instructions
INSTALLATION INSTRUCTIONS © Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Tel. 913/397.8200 or 800/800.1020 Fax 913/397.8282 Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Tel. 44/0870.8501241 Fax 44/0870.8501251 Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax 886/2.2642.9099 All rights reserved.
INSTALLATION INSTRUCTIONS INTRODUCTION The GPSMAP 2006C/2010C Multi-Function Display (MFD) and GPS 17 must be properly installed according to the following instructions for the best possible performance. To complete the installation, you need the appropriate fasteners, tools, and mounts listed in each section. These items are available at most marine dealers. Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding.
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Surface Mount Tools • • • • Drill and Drill Bit Screwdriver Pencil Mounting Hardware (not included) NOTE: Mounting hardware (fasteners) not included. Mounting holes are 5/16" (7.9 mm) in diameter. To install the Bail Mount and unit: 1. Using the bail mount as a template, mark the location of the four mounting holes. Be sure to leave at least two inches of clearance behind the unit for the wiring. 2.
INSTALLATION INSTRUCTIONS Flush Mount Tools • • • • • • • • • • Flush Mount Template Jig saw Masking tape Scissors Drill Drill bits—1/8" (3 mm) and 3/8" (6 mm) 1/16" (2 mm) Allen (Hex) wrench Sockets or wrenches Hammer Center punch Flush Mount To flush mount the GPSMAP 2006C/2010C: 1. 2. 3. 4. 5. Trim the Flush Mount Template and tape it in the location you want. Using the center punch, indent the center of each mounting hole location. Using an 1/8” (3 mm) drill bit, drill the four mounting holes.
INSTALLATION INSTRUCTIONS Installing the GPS 17 The GPS 17 can be flush mounted or installed on any standard 1" O.D. (Outer Dimension), 14 threads-per-inch marine mount. When mounting the GPS 17, the cable can be run externally or through the mounting panel or through the center of the marine mount. The GPS 17 connects to the 18-pin Power/Data Cable on the GPSMAP 2006C/2010C and provides the GPS/WAAS signal for the unit.
INSTALLATION INSTRUCTIONS To attach the enclosed pole mount to the GPS 17: 1. Thread the cable though the pole mount. 2. Align the tab on the mount to the notch on the GPS 17. 3. Use the enclosed screws to secure the mount to the base. Attaching the Pole Mount to the GPS 17 To mount the GPS 17 with cable outside mount: 1. Place the cable in the vertical slot along the side of the base of the unit. 2. Screw the GPS 17 onto the mount. DO NOT overtighten the head.
INSTALLATION INSTRUCTIONS Wiring There are two wiring diagrams provided for you convenience. The first is a simple hook-up showing the GPSMAP 2006/2010 (using the 18pin wiring harness), the GPS 17 and the alarm circuit. The Alarm does not have to be wired for the unit to function. The second is a complete wiring diagram showing the GPSMAP 2006/2010 (using the 18-pin wiring harness) interfacing with a variety of different equipment.
INSTALLATION INSTRUCTIONS + SHIP'S BATTERY 10-32 VOLTS - GARMIN GSD 20 SOUNDER MODULE (SEE GSD 20 INSTALL INSTRUCTIONS) (-) (-) (-) 4. A GARMIN SOUNDER UNIT (OTHER THAN GSD 20) CAN PROVIDE WATER DEPTH, WATER TEMPATURE, AND SPEED VIA NMEA DATA FOR DISPLAY ON THE GPSMAP 2006/2010.
INSTALLATION INSTRUCTIONS Final Wiring Connection Once all the wiring is complete, plug the 18-pin harness into the center connector on the backside of the GPSMAP 2006/2010. The 5-pin port on the right side is intended for future interfacing features and does not require connection at this time. With power applied to the circuit, you may test the installation by pressing the POWER Manual for steps on initializing the receiver. 18-Pin Connector 10 key on the front of the unit.
INSTALLATION INSTRUCTIONS FLUSH MOUNT DRILLING TEMPLATE Drill using a 11/64” or 4.
© Copyright 2005 Garmin Ltd. or its subsidiaries Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062, U.S.A. Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL, U.K. Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan www.garmin.com Part Number 190-00228-01 Rev.
