quick reference guide Edge® 605/705 GPS-ENABLED BIKE COMPUTER MB
Warning: This product contains a lithium-ion battery. See the Important Safety and Product Information guide in the product box for important battery safety information. Warning: Always consult your physician before you begin or modify any exercise program. See the Important Safety and Product Information guide in the product box for product warnings and other important information. Buttons ➊ power • Press and hold to turn the Edge on/off. • Press to turn the backlight on/off.
➍ thumb stick/enter Resetting the Edge • Move the thumb stick to scroll through menus, options, and data fields. • Press in the thumb stick to select options and to acknowledge messages. Icons ➎ start/stop Press to start/stop the timer. ➏ menu • Press to open the menu page. • Press and hold to lock/unlock the Edge buttons. ➐ in/out Press to zoom in/out on the map page and the altimeter page. If your Edge is locked up/frozen, press mode and reset/lap simultaneously to reset the Edge.
Step 1: Charge the Battery You can charge the Edge using the AC charger or the USB cable and your computer. Note: To prevent corrosion, thoroughly dry the mini-USB port, weather cap, and surrounding area before charging or connecting to a personal computer. To charge the Edge: 1. On the back of the Edge, pull up the weather cap from the mini-USB port. 2. Plug the mini-USB end of the AC or USB cable into the mini-USB port on the back of the Edge. Mini-USB port under weather cap 3.
be used under the mount for a better viewing angle. 2. Attach the bike mount securely using two cable ties. To install the Edge on your bike: 3. Align the Edge with the bike mount so that the slots on the back of the unit are parallel with the rails on the mount. 1. Place the wedge on the bike stem or the handlebars, and then place the bike mount on the wedge. Make sure the release lever is on the left. Release lever Wedge Rail Slot Bike mount For bars with a diameter less than 1 in (25.
To release the Edge: Press down on the release lever, and slide the Edge to the right. Step 3: Turn on Your Edge Press and hold to turn on your Edge. Follow the on-screen configuration instructions. Step 4: Acquire Satellite Signals It may take 30–60 seconds to acquire signals. Go outdoors to an open area. For the best reception, make sure the front of the Edge is oriented toward the sky. Step 5: Save Your Home Location (Optional) You can set a home location for the place you return to most often. 1.
your activity, you must reestablish the connection with the Edge, see the Edge 605/705 Owner’s Manual. Heart Rate Monitor Wear the heart rate monitor directly on your skin, just below your breastplate. It should be snug enough to stay in place during your run. 1. Push one tab on the strap through the slot in the heart rate monitor. Press the tab down. 2. Wet both electrodes on the back of the heart rate monitor to create a strong connection between your chest and the transmitter. 3.
GSC 10 mount and a cable tie. The pedal magnet must be within 5 mm of the GSC 10 and the indication line on the pedal magnet must line up with the indication line on the GSC 10. Both magnets must be aligned with their respective indication lines for the Edge to receive data. To install the GSC 10: 1. Place the GSC 10 on the rear chain stay (on the side opposite the drive train). Loosely attach the GSC 10 using two cable ties. 2. Attach the pedal magnet to the crank arm using the adhesive 3.
Spoke magnet GSC 10 Pedal magnet Sensor arm indication line GSC 10 and magnet alignment not enough room between the sensor arm and the spoke. The magnet must be aligned with the sensor arm indication line. 4. Loosen the screw on the sensor arm and move it to within 5 mm of the spoke magnet. You can also tilt the GSC 10 closer to either magnet for improved alignment. 5. Press the Reset button on the GSC 10. The LED turns red, then green. Pedal to test the sensor alignment.
6. When everything is aligned and working correctly, tighten the cable ties, sensor arm, and spoke magnet. To set your bike profile: Press menu > select Settings > Profile & Zones > Bike Profile. Step 7: ���������� Set Your Profiles The Edge uses information that you enter about yourself and your bike to calculate accurate ride data. To set your user profile: Press menu > select Settings > Profile & Zones > User Profile. Use the thumb stick to change the field values.
Step 9: Download Free Software 1. Go to www.garmin.com/edge. 2. Follow the on-screen instructions to download Garmin Training Center® or Garmin Connect™. Step 10: Transfer History to Your Computer 1. Plug the small end of the USB cable into the mini-USB port on the back of the Edge (under the weather cap). 2. Connect the larger end of the USB cable to an available USB port on your computer. 3. Open Garmin Connect or Garmin Training Center. Follow the upload instructions included with the software.
© 2009 Garmin Ltd. or its subsidiaries Garmin® is a trademark of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. Garmin Training Center®, Edge®, Garmin Connect™, GSC™ 10, Dynastream™, ANT™, and ANT+Sport™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used without the express permission of Garmin. Other trademarks and trade names are those of their respective owners. Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, USA Tel.
