VARIA UT800 ™ Owner’s Manual
© 2017 Garmin Ltd. or its subsidiaries All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates and supplemental information concerning the use of this product.
Table of Contents Introduction..................................... 1 Installing the Out-Front Mount............... 2 Installing the Helmet Mount................... 5 Device Overview...................................... 6 Turning On the Device............................ 6 Bike Light Status LEDs........................... 6 Device Settings................................ 6 Pairing Your Bike Light with Your Edge 830 or 1030.............................................
Introduction WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. The device is intended for outdoor use. Without proper airflow during use, the device may become hot. Handle with care.
Installing the Out-Front Mount You can use the out-front mount to install the headlight and your Edge device. Garmin recommends that you adjust the mount for the Edge viewing angle before you install and adjust the headlight angle. 1 Select a secure location to mount the Edge device and headlight where they do not interfere with the safe operation of your bike. 2 Use the 2.5 mm hex key to remove the screw from the handlebar connector .
9 Insert the screw , and hand tighten. 10 Align the notches of the quarter-turn adapter with the tabs on the bottom of the mount. 11 Press up slightly, and turn the adapter counterclockwise until it locks into place. 12 Adjust the headlight angle so it is parallel to the ground, and use the 4 mm hex key to tighten the screw.
NOTE: You should check the tightness of the screw periodically.
Installing the Helmet Mount 1 Select a secure location to mount the headlight where it does not interfere with the safety and comfort of your helmet. 2 Attach the mount using both straps. 3 Lock the straps by pressing down the clasp. 4 Connect the adapter to the headlight. 5 Insert the screw , and hand tighten. 6 Align the tabs on the adapter with the notches of the mount. must be in the open position. The lever 7 Insert the device into the mount.
The lever must be flush with the base. 9 Adjust the headlight angle, and use the 4 mm hex key to tighten the screw. NOTE: You should check the tightness of the screw periodically. Device Overview Device key Hold for 1 sec. to turn the device on. Hold for 2 sec. to turn the device off. Hold to enter pairing mode (Pairing Your Bike Light with Your Edge 830 or 1030, page 7). Select to change operating modes. Status LED View device status (Bike Light Status LEDs, page 6).
Pairing Your Bike Light with Your Edge 830 or 1030 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ bike lights while pairing. 2 Turn on the Edge device. 3 Select > Sensors > Add Sensor > Search All. 4 While the headlight is turned off, hold the Varia device key for 2 seconds to enter pairing mode. The status LED flashes purple, and the headlight turns on. The device is in pairing mode for 5 minutes or until you press the device key.
Light Mode Settings From the Sensors menu, select Lights > Network Options > Light Mode. Auto: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. High Visibility: Sets the light intensity to flash mode or the brightest setting available. Trail: Automatically adjusts the light intensity and light mode based on the ambient light and time of day. This mode is recommended for mountain biking.
Device Information Specifications Battery type Rechargeable, built-in lithium-ion battery Battery life Up to 1 yr. in standby mode See Headlight Light Intensity Modes and Battery Life, page 9 Operating temperature range From -15° to 50°C (from 5° to 122°F) Charging temperature range From 0º to 45ºC (from 32º to 113ºF) Wireless frequency 2.
Charging the Device WARNING This device contains a lithium-ion battery. See the Important Safety and Product Information guide in the product box for product warnings and other important information. NOTICE To prevent corrosion, thoroughly dry the USB port, the weather cap, and the surrounding area before charging or connecting to a computer. NOTE: The device does not charge when outside the approved temperature range (Specifications, page 9). 1 Pull up the weather cap from the USB port.
Cleaning the Device 1 Wipe the device using a cloth dampened with a mild detergent solution. 2 Wipe it dry. After cleaning, allow the device to dry completely. Troubleshooting Resetting the Device You can reset the device if it stops responding. Hold the device key for 8 seconds until all the LEDs turn off. Resetting deletes the pairing connections from the device. Thermal Safety Shutdown To prevent overheating, the Varia device may turn off when operated at a high intensity in warm, stagnant air.
Other Compatible Devices Pairing Your Bike Light with Another Edge Device 1 Bring the Edge device within range (1 m) of the sensor. NOTE: Stay 10 m (33 ft.) away from other ANT+ bike lights while pairing. 2 Turn on the Edge device. 3 From the Sensors menu, select Add Sensor > Search All. 4 While the headlight is turned off, hold the Varia device key for 2 seconds to enter pairing mode. The status LED flashes purple. 5 Select your sensor.
Index A accessories 11 ANT+ sensors 7 B battery 9, 11 charging 10 brightness 8, 11 C charging 10 cleaning the device 11 customizing the device 6 D device, care 10 E Edge 6–8, 12 G Garmin Express, updating software 11 GPS, signal 7 I installing 2, 5 K keys 6 M mounting the device 2, 5 P pairing 7, 12 remote control 12 R remote control, pairing 12 resetting, device 11 S satellite signals 7 settings 7, 8 smartphone 7 software, updating 11 specifications 9 speed 8 T temperature 11 troub
support.garmin.
