Owner's Manual

• Select Track Color, and select a color.
Saving a Track as a Route
1
Select Nav Info > Tracks > Saved Tracks.
2
Select a track.
3
Select Edit Track > Save As > Save as Route.
Browsing for and Navigating a Recorded Track
Before you can browse a list of tracks and navigate to them, you
must record and save at least one track (Tracks, page 16).
1
Select Nav Info > Tracks > Saved Tracks.
2
Select a track.
3
Select Follow Track.
4
Select an option:
• To navigate the track from the starting point used when
the track was created, select Forward.
• To navigate the track from the destination point used
when the track was created, select Backward.
5
Review the course indicated by the colored line.
6
Follow the line along each leg in the route, steering to avoid
land, shallow water, and other obstacles.
Deleting a Saved Track
1
Select Nav Info > Tracks > Saved Tracks.
2
Select a track.
3
Select Delete.
Deleting All Saved Tracks
Select Nav Info > Manage Data > Clear User Data > Saved
Tracks.
Retracing the Active Track
The track currently being recorded is called the active track.
1
Select Nav Info > Tracks > Follow Active Track.
2
Select an option:
• Select the time the active track began.
• Select Entire Log.
3
Review the course indicated by the colored line.
4
Follow the colored line, steering to avoid land, shallow water,
and other obstacles.
Clearing the Active Track
Select Nav Info > Manage Data > Tracks > Clear Active
Track.
The track memory is cleared, and the active track continues
to be recorded.
Managing the Track Log Memory During Recording
1
Select Nav Info > Tracks > Active Track Options.
2
Select Record Mode.
3
Select an option:
• To record a track log until the track memory is full, select
Fill.
• To continuously record a track log, replacing the oldest
track data with new data, select Wrap.
Configuring the Recording Interval of the Track Log
You can indicate the frequency at which the track plot is
recorded. Recording more frequent plots is more accurate but
fills the track log faster. The resolution interval is recommended
for the most efficient use of memory.
1
Select Nav Info > Tracks > Active Track Options > Record
Interval.
2
Select an option:
• To record the track based on a distance between points,
select Interval > Distance > Change, and enter the
distance.
• To record the track based on a time interval, select
Interval > Time > Change, and enter the time interval.
• To record the track plot based on a variance from your
course, select Interval > Resolution > Change, and enter
the maximum error allowed from the true course before
recording a track point. This is the recommended
recording option.
Boundaries
CAUTION
The Beeper setting must be turned on to make alarms audible
(System Settings, page 37). Failure to set audible alarms could
lead to injury or property damage.
Boundaries allow you to avoid or remain in designated areas in
a body of water. You can set an alarm to alert you when you
enter or exit a boundary.
You can create boundary areas, lines, and circles using the
map. You can also convert saved tracks and routes into
boundary lines. You can create a boundary area using
waypoints by creating a route from the waypoints, and
converting the route into a boundary line.
You can select a boundary to act as the active boundary. You
can add the active boundary data to the data fields on the chart.
Creating a Boundary
1
Select Nav Info > Boundaries > New.
2
Select a boundary shape.
3
Follow the on-screen instructions.
Converting a Route to a Boundary
Before you can convert a route to a boundary, you must create
and save at least one route (Creating and Saving a Route,
page 14).
1
Select Nav Info > Routes.
2
Select a route.
3
Select Edit Route > Save as Boundary.
Converting a Track to a Boundary
Before you can convert a track to a boundary, you must record
and save at least one track (Saving the Active Track, page 16).
1
Select Nav Info > Tracks > Saved Tracks.
2
Select a track.
3
Select Edit Track > Save As > Save as Boundary.
Editing a Boundary
1
Select Nav Info > Boundaries.
2
Select a boundary.
3
Select an option:
• To edit the appearance of the boundary on the chart,
select Display Options.
• To change the boundary lines or name, select Edit
Boundary.
• To edit the boundary alarm, select Alarm.
Setting a Boundary Alarm
Boundary alarms alert you when you are within a specified
distance of a set boundary. This can be helpful when attempting
to avoid certain areas or when you should be very alert in
certain areas, such as shipping lanes.
1
Select Nav Info > Boundaries.
2
Select a boundary.
Navigation with a Chartplotter 17