Overview A 20 19 1 18 17 16 15 2 14 13 3 12 11 4 10 9 5 8 6 7 3
Package contents Package contents 1 Right armrest (775 × 610 × 90 mm), ×1 2 Backrest for the corner element (530 × 610 × 90 mm), ×1 3 Seat for the corner element (1,330 × 700 × 310 mm), ×1 4 Backrest for the sofa (1,300 × 610 × 90 mm), ×1 5 Seat for the sofa (1,300 × 670 × 310 mm), ×1 6 Left armrest (775 × 610 × 90 mm), ×1 7 Seat cushion for the corner element (1,325 × 690 × 70 mm), ×1 8 Seat cushion for the sofa (1,210 × 660 × 70 mm), ×1 9 Pillow for the backrest (625 × 400 × 120 mm), ×3 10 Pillow for the
General information IMPORTANT, RETAIN FOR FURTURE REFERENCE: READ CAREFULLY The pillow and seat covers are not suitable for bleaching. The pillow and seat covers are not suitable for being dried in a drum dryer. General information The pillow and seat covers are not suitable for ironing. Reading and storing the assembly instructions These assembly instructions accompany this rattan effect corner set (hereinafter referred to only as “rattan sofa set”).
Preparation complete (see Fig. A). Risk of damage! Improper handling of the rattan sofa set 3. Check whether the individual parts of the rattan sofa set exhibit damages. If this is the may damage it. case, do not assemble or use the rattan sofa −− Place the rattan sofa set on an easily set. Contact the manufacturer via the service accessible, level, dry, heat-resistant and address specified on the warranty card. sufficiently stable surface.
Assembly of the rattan sofa set Use the open-ended spanner and the hex key to tighten the hexagon socket screws. 3. Hook the backrest for the sofa 4 into the left armrest 6 . Place the hexagon socket screws (6 × 60), the washers and the hexagon nuts on the points shown. Remove the plastic plug 20 from the connection hole (see Assembly of sitting arrangement 1, step 3). Use the openended spanner and the hex key to tighten the hexagon socket screws. 4.
Cleaning and maintenance 1. Insert the side panels for the stool/table 12 in the frame for the stool/table 11 (see Assembly of the stool/table, step 1). 2. Turn the frame for the stool/table on its side. Place the hexagon socket screws (6 × 35) 18 and the washers 17 on the points shown (see Assembly of the stool/table, step 2). Tighten the hexagon socket screws with the hex key 14 . 3. Turn the frame for the stool back into a level position. 4.
Assembly Assembly Assembly of sitting arrangement 1 1 2 16 15 14 17 19 1+2 1 2 ×1 2 2 ×1 19 3 3 19 2 1 ×1 19 19 6 × 60, ×6 17 17 ×12 16 ×6 16 9
Assembly 3 3+4 4 20 ×1 5 6 4 ×1 6 17 ×1 20 16 19 ×1 19 6 × 60, ×8 4 17 ×16 17 16 19 16 ×8 20 5 19 6 4 19 17 16 10 16 17 19
Assembly 5+6+7 5 19 19 17 6 × 60, ×4 17 ×8 16 16 20 ×4 3 20 6 5 4 ×1 1 7 20 2 17 ×1 8 16 16 19 ×1 9 ×3 10 ×2 6 7 11
Assembly Assembly of sitting arrangement 2 1 6 2 15 14 17 16 19 1+2 2 ×1 3 2 19 ×1 6 2 6 19 3 ×1 19 19 6 × 60, ×6 17 17 ×12 16 ×6 16 12
Assembly 3 3+4 1 20 ×1 4 1 4 ×1 5 ×1 20 ×1 16 19 17 19 6 × 60, ×8 4 17 ×16 16 16 17 ×8 19 20 1 5 19 4 16 17 19 17 19 16 13
Assembly 5 5+6+7 19 19 17 6 × 60, ×4 17 ×8 16 16 ×4 20 20 20 ×1 3 1 5 7 6 4 2 ×1 8 19 19 17 ×1 16 9 ×3 10 ×2 6 14 7
