D ® S NL F GB GARDENA NL S I E P DK FIN I E F P GB Betriebsanleitung Spindelmäher Operating Instructions Cylinder Lawnmower Mode d’emploi Tondeuse hélicoïdale Instructies voor gebruik Kooimesmaaier Bruksanvisning Handgräsklippare Istruzioni per l’uso Rasaprato a mano Manual de instrucciones Cortacésped helicoidal Instruções de utilização Cortador de relva cilíndrico Brugsanvisning Håndplæneklipper Käyttöohje Työnnettävä ruohonleikkuri DK D Art. 4021 Art.
GARDENA Cylinder Lawnmower 300 C / 380 C Welcome to the Garden of GARDENA... GB Translation of the original instructions from German. Please read these operating instructions carefully and observe the notes given. Use these instructions to familiarise yourself with the cylinder lawnmower, its correct use and the notes on safety. For safety reasons, children under the age of 16 as well as persons not familiar with these operating instructions should not use this cylinder lawnmower.
The safety distance between the blade cylinder and the operator that is created by the guiding spar is to be always maintained. When mowing embankments and slopes, special care must be taken: v Make sure you always keep a safe distance and wear shoes with a nonslip sole. Always cut diagonally to the slope. Take special care when moving backwards and when pulling the lawn mower.
GB After relatively long intervals between mowing (e.g. holiday), first of all cut in one direction with the cutting height as high as possible (42 mm), then cut in the crosswise direction at the cutting height required. The blades of grass should not be more than 12 cm long if they are to be cut with a cylinder mower. If possible only cut the grass when it is dry. If the grass is damp, the cutting pattern will be uneven.
7. Troubleshooting GB DANGER ! Cutting tool can cause injuries ! V Wear suitable work gloves when rectifying faults. Fault Possible Cause Rectification Abnormal Noises Screws / components loose. v Tighten screws. Foreign bodies on the blade. v Remove foreign bodies. Notch in the blade. v Remove notches with grindstone. Blades are striking each other too hard. v Adjust cutting mechanism. Blade adjustment incorrect. v Adjust cutting mechanism. Blade blunt. v Regrind or replace blade.
Regrinding / repairs : A On safety grounds, only original GARDENA spares may be used. GB Please contact GARDENA Service if it is necessary to replace the cutting tool, which will only become blunt after several years use if well-maintained. Repairs to the cylinder mower and the installation of the blades can be undertaken by suitable specialist workshops. Have the cylinder mower checked over in the autumn if possible so that it is ready for use immediately when the next lawn-mowing season starts.
Produkthaftung Wir weisen ausdrücklich darauf hin, dass wir nach dem Produkthaftungsgesetz nicht für durch unsere Geräte hervorgerufene Schäden einzustehen haben, sofern diese durch unsachgemäße Reparatur verursacht oder bei einem Teileaustausch nicht unsere Original GARDENA Teile oder von uns freigegebene Teile verwendet werden und die Reparatur nicht vom GARDENA Service oder dem autorisierten Fachmann durchgeführt wird. Entsprechendes gilt für Ergänzungsteile und Zubehör.
Deutschland / Germany GARDENA Manufacturing GmbH Central Service Hans-Lorenser-Straße 40 D-89079 Ulm Produktfragen: (+ 49) 731 490 - 123 Reparaturen: (+ 49) 731 490 - 290 service@gardena.com Argentina Husqvarna Argentina S.A. Vera 745 (C1414AOO) Buenos Aires Phone: (+ 54) 11 4858-5000 diego.poggi@ar.husqvarna.com Australia Husqvarna Australia Pty. Ltd. Locked Bag 18 Gosford NSW 2250 Phone: (+ 61) (0) 2 4372 1500 customer.service@ husqvarna.com.
