TABLE TOP PATIO HEATER Owner’s Manual Model : HPS-C-PC IMPORTANT Read this manual carefully before assembling, using or servicing this heater. Keep this manual for future reference. R R ANSI Z83.26-2007/CSA 2.
Contents DANGER General Safety Information....................................... 1 Contents Breakdown ............................................. 4 Package Contents .................................................. 4 Assembly.................................................................. 5 DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
WARNING • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone. WARNING California Proposition 65 Combustion by products produced when using this product contain chemicals known to the state of California to cause cancer, birth defects, and other reproductive harm.
Contents Breakdown 1 Finial 2 Reflector cap 3 Nuts (qty. 3) 4 Reflector 5 Washers (qty. 6) 6 Reflector spacers (qty. 3) 15 3/16" Stainless bolts (qty. 4) 7 Emitter 8 M6X60 bolt (qty. 1) 16 9 Nuts (qty. 4) Post with burner assembly 17 10 Wire guard 3/16" Stainless bolts (qty. 4) 11 Access panel 19 Bolt M5X8 / Nut M5 / washer (qty. 1) 18 Heater housing 12 Base 13 Ring weight 14 M6X20 bolts (qty. 4) Package Contents This outdoor/tabletop heater requires some assembly.
Assembly For additional assistance or service, please call: 888-775-1330. STEP 1: Attach post with burner assembly onto heater housing, using 4pcs 3/16" Stainless bolts and M5X8 bolt / Nut M5/ washer, Keep the access panel open. STEP 2: Attach ring weight to base, using 4pcs M6X20 bolts. STEP 3: Put 3pcs reflector spacers into the hole in emitter using 3pcs nuts to firm the reflector spacers inside of the emitter.
A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT). or the Standard for Cylinders, Spheres and Tubes for Transportation of Dangerous Goods and Commission, CAN/CSA-B339. Provided with a listed overfilling prevention device.
Portable Heater Location 1. This portable heater is intended for outdoor use only. Always ensure that adequate fresh air ventilation is provided. 2. Always maintain proper clearance to combustible. materials, i.e. top 24 inches and sides 36 inches minimum. 3. The heater must be put on a strong and stable table. 4. Never operate the heater in an explosive atmosphere like in areas where gasoline or other flammable liquids or vapors are stored. CEILING Procedure for Leakage Test 1.
Troubleshooting If the problem is: And this condition exists: Then do this Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Open gas line and bleed it (pressing control Pilot won’t light Air in gas line knob in) for not more than 1 - 2 minutes or until you smell gas Low gas pressure with cylinder valve Note: Heater operates at reduced efficiency below 40ºF fully open Clean dirt from around pilot Connection between gas valve and Ti
.. .. . . Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. Ґ . . . Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. Never leave LP cylinder exposed to direct sunlight or excessive heat.
