User manual
Switching between 12 h and 24 h modes
The weekday timer switch must be in the time display mode.
Briefl y press the “HRS” button to switch between the 12 h and 24 h modes.
In the 12 h mode, “AM” is displayed above the second display for before noon and “PM” for
afternoon.
Reset
To reset the week day timer switch, press the countersunk reset button briefl y e.g. with a
toothpick.
The display will briefl y show all display segments, then the DCF reception is started (as
described in “Getting Started” chapter).
☞
During a reset, the programmed setting are retained for the on/off times and the
countdown.
Lighting of the LC display / night light feature
With the “ ” switch, the lighting of the display can be turned on or off.
This can also be used as a night light due to the spacious and bright lighting.
Maintenance and Cleaning
The product does not require maintenance. The product contains no parts that require servic-
ing. Therefore, do not open/dismantle it. Maintenance or repairs may only be performed by
qualifi ed personnel or a specialist repair shop.
Before cleaning, disconnect the weekday timer switch from the power supply. To do this, pull
it completely out of the mains socket (the wall socket). The settings remain unchanged with
the help of the integrated NiMH battery.
Use a clean, dry, soft cloth for cleaning. Do not press too hard on the display; this can lead to
scratches and could also damage the display!
Dust can easily be removed using a clean, soft and long-bristled brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical solutions,
since these could damage the housing or even impair operation.
Disposal
Dispose of the unserviceable product according to the relevant statutory regulations!
Technical Data
Operating voltage ................. 230 V/AC, 50 Hz
Switching capacity ................max. 3680 W
Protection class .................... I
Model: ................................... Relay; 1-pole disconnection
Child-proof lock: .................... yes, integrated into socket
Switching times per day ........ 4 On/off programs
Shortest switching time ......... 1 min
Countdown timer time ........... 1 min to max. 23 h, 59 min
Data retention ......................... via internal NiMH battery (max. 10 hours with fully charged battery)
Ambient temperature ............0 °C to +40 °C
Ambient humidity ..................0% to 90% relative humidity, not condensing
Dimensions ........................... 70.5 x 132 x 37 mm (W x H x D), without plug)
Weight ..................................225 g
Proceed as follows for programming an off-time:
Press the “MENU” button to select and display the off-time of the respective program group
(e.g. “1
”).
Set the hours by pressing the “HRS” button (for quick adjustment hold the button a bit longer).
Set the minutes by pressing the “MIN/CD” button (for quick adjustment hold the button a bit
longer).
With the “DAY/WEEK” button you can now choose on which day of the week (or on which
weekday combinations) the switching program of the program group is to be executed. The
days of the week will be shown at the top of the display.
☞
You are advised to program the same day of the week (or the same combination of
weekdays) as the on-time.
If you do not press any button for several minutes, the settings will be saved and the display
returns to the current time.
This completes the programming mode.
Enable / disable switch-on / off time of a program group
You can also temporarily disable a program group set by you, for example on holiday. The set-
tings are retained, but the switching program will not run any longer.
Disable program group:
To disable the on-time or off-time of a program group (for example, when you are on holiday),
fi rst select the desired on-time or off-time of the program group with the “MENU” button.
Keep the button “DAY/WEEK” pressed for more than 2 seconds, the display shows “- - : - -”,
the on-time or off-time of the program group is deactivated and will not be carried out (a
programmed on/off-time will not be deleted, however – only the execution of the switching
program is deactivated).
☞
Always disable the on-time and the off-time of the respective program group.
Enable the program group once again:
Select the preferred on/off-time of the program group with the “MENU” button and press one
of the 3 buttons “HRS”, “MIN/CD” or “DAY/WEEK” briefl y.
If you have already programmed the respective on/off-time (and the settings have been
saved) it will now be reactivated and shown on the display, i.e. the respective switching
program is active again.
☞
Always activate the on-time and the off-time of the respective program group.
Countdown Mode
In the countdown mode you can set a time between min. 1 minute and max. 23 hours, 59 minutes.
With the start of the countdown the device is switched on. When the countdown is over (“0:00:00”)
the device is switched off.
☞
When a countdown starts, all automatic switching programs are disabled! That
means that no automatic switching on or off will take place at the defi ned times and
weekdays in the program groups.
Setting the countdown time
The weekday timer switch must be set to the normal time indication.
Press the “MENU” button as many times until “CD” is shown to the top left of the display.
Set the hours by pressing the “HRS” button (for quick adjustment hold the button a bit longer).
Set the minutes with the “MIN/CD” button (for quick adjustment hold the button a bit longer).
If you do not press any button for several minutes, the settings will be saved and the display
returns to the current time.
This completes the programming mode.
Start countdown
The weekday timer switch must be set to the normal time indication.
Press the “MIN/CD” button briefl y to start the countdown mode.
☞
This is possible only if you have set a countdown time as described above.
The device is switched on, the display shows the elapsed countdown time and the symbol
“CD” in the top left corner.
During a running countdown you can switch between the time display and the countdown
display with the “MENU” button. In the time display, the symbol “CD” fl ashes when the count-
down has started.
When the countdown is over (“0:00:00” in the display), the device is switched off and the
display returns to the time display after 8 seconds.
Terminate countdown prematurely
In the display, the currently running countdown time must be shown (if necessary, briefl y
press the “MENU” button).
To stop the countdown, briefl y press the “MIN/CD” or “DAY/WEEK” button.
The original countdown time will be displayed, the device is switched off. After 8 seconds, the
display returns to the normal time display.
You can now start the countdown again, if you wish.