Instructions / Assembly

ManualsBrandsGAME ManualsOutdoor ShowersBlack and Gold Outdoor Solar Shower

A A

B B

4 3

85001-BB Assembly Drawings

FIGURE 5

Hose attachment

port/Water Inlet

Shower Arm

Upper Tube

Lower Tube

Footwash

Knob

Shower Head

FIGURE 2

FIGURE 3 FIGURE 4

FIGURE 5

FIGURE 6FIGURE 1

When using tools, care must be taken not to scratch and/or damage gold plating. We recommend using a cloth between

wrench and shower parts to avoid scratching and/or damage.

MOUNTING THE SHOWER: CONCRETE/MASONRY INSTALLATION ONLY

1. Choose a location for shower that receives the most direct sunlight.

2. Use the base plate on the lower shower tube to mark the position of the mounting holes. FIGURE 3

3. Remove shower. Drill ½” diameter holes, 2” deep, using the marks just created.

4. Insert expansion nuts into holes. Place the long bolt inside the

expansion nut and TAP with a hammer to slightly expand the nut.

5. Remove bolt and place the base plate on the lower shower tube over the holes and secure to surface

with bolts and washers provided. NOTE: Base plate will appear loose until shower is fully secured to the

surface.

ASSEMBLING THE SHOWER

1. If not assembled, assemble the shower head assembly. FIGURE 1

2. Install footwash and 19mm gasket washer into lower tube. FIGURE 3

3. Install the shower head assembly onto the end of the shower head attachment pipe.

DO NOT OVERTIGHTEN. FIGURE 2

4. Install the shower head attachment pipe into the tting on the upper shower tube. Turn gently until

pipe is secure and shower head is pointing down.

NOTE: If shower arm is stopped by end of threads in any other orientation, rotate shower arm counter-

clockwise until it is pointed downward. FIGURE 2

5. Install the 85mm O-Ring into the circular groove on the lower shower tube. FIGURE 4

6. Set the upper shower tube on the lower shower tube. Rotate the upper shower tube to lock it to the

lower shower tube. NOTE: The shower head, footwash, and temperature knob should all face the same

direction. FIGURES 4 & 6

7. Attach garden hose adapter to the water inlet port of the solar shower. FIGURE 5

8. Attach garden hose to the garden hose adapter on the solar shower and to the the water supply.

NOTE: Be sure that the garden hose is located safely to avoid any tripping hazards. FIGURE 5

INSTRUCTIONS English

Before you begin, please check to ensure you have all the parts. Read ALL the directions before beginning.

The shower uses solar energy from the sun to heat the water.

1 - Shower Upper Tube Assembly 1

2 - Shower Lower Tube Assembly 1

3 - 85mm O-Ring 1

4 - Shower Head Assembly 1

4a Shower Head 1

4b 24mm Shower Head Gasket 1

4c 19mm Gasket Washer 1

4d 1-1/4” Shower Connector 1

5 - Shower Head Attachment Pipe 1

6 - 19mm Rubber Gasket 3

7 - Footwash 1

8 - Concrete Anchor System 4

8a M10x25 Bolt 4

8b M10 Washer 4

8c 12/40mm Drop-in

Concrete Anchor 4

9 - Garden Hose Adapter 1

TOOLS NEEDED

1⁄” socket or adjustable wrench

Water Inlet Port

Garden Hose

Summary of content (2 pages)

PAGE 1
INSTRUCTIONS (English) The shower uses solar energy from the sun to heat the water. Before you begin, please check to ensure you have all the parts. Read ALL the directions before beginning.
PAGE 2
INITIAL SET UP OF THE SHOWER 1. Shower will take about 3 to 5 minutes to fill. 2. Lift temperature knob and rotate so that the temperature knob is in the full HOT position. 3. When water flows from shower head, turn temperature knob off. Turning the shower off allows the water to begin heating. 4. Shower is ready to absorb sunlight and heat your water. NOTE: Depending on available sunlight and outside temperature, it may take up to 2 hours or longer to fully heat the water.