SandPRO™ POOL FILTER SYSTEM OWNER’S MANUAL MODELS 50D (items 4710 and 61201-BB) and 75D (item 4711 and 61301-BB) IMPORTANT SAFETY RULES Read all instructions BEFORE assembling and using this product. KEEP THIS MANUAL. MODEL 75D (item 4711) MODEL 50D (item 4710) Sand not included. USE ONLY #20 Silica Sand with a particle size of 0.45 mm – 0.55 mm IMPORTANT DO NOT RETURN PRODUCT TO STORE For technical assistance and missing parts, call or email Customer Service 1.888.339.
YOUR POOL FILTER SYSTEM HAS BEEN ENGINEERED AND MANUFACTURED TO OUR HIGHEST STANDARD FOR DEPENDABILITY, EASE OF OPERATION AND SAFETY. WITH PROPER CARE, IT WILL GIVE YOU YEARS OF DURABLE, TROUBLE-FREE PERFORMANCE. THANK YOU FOR YOUR PURCHASE. READ ALL INSTRUCTIONS BEFORE ASSEMBLING AND USING THIS PRODUCT. FAILURE TO FOLLOW INSTRUCTIONS CAN CAUSE SEVERE AND/OR FATAL INJURY. IMPORTANT DO NOT RETURN PRODUCT TO STORE For technical assistance and missing parts, call or email Customer Service 1.888.339.
TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Safety Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Appendix: Exploded Parts Diagram . . . . . . . . . . . . . .
1. SAFETY WARNINGS READ ALL WARNINGS BELOW. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH. • For use with above-ground pools only. • Do not block inlet or outlet ports. • Connect ONLY to a Ground-Fault Circuit Interrupter (GFCI) power outlet. Consult a qualified, professional electrician for safe and proper installation of the required electrical outlet. • Incorrectly installed equipment may fail, causing severe injuries or damage to the pump-filter system.
3. TECHNICAL SPECIFICATIONS SandPRO 50D (item 4710, 1/2 hp) Item U.S. Units Pump Flow Rate Design Flow Rate MAX Operating Pressure Filtration Area Rated Voltage Sand Volume 2,400 GPH 912 GPH 40 psi 0.76 ft2 110 V 50 lbs SandPRO 75D (item 4711, 3/4 hp) Item Pump Flow Rate Design Flow Rate MAX Operating Pressure Filtration Area Rated Voltage Sand Volume U.S. Units 3,120 GPH 1,392 GPH 40 psi 1.16 ft2 110 V 75 lbs NOTE: Requires 50 lbs (22.6 kg) not included Metric Units 9.1 m3/hr 3.5 m3/hr 2.75 Bar 0.
4.
5 15 12 14 13 11 19 16 20 17 10 7 22 11 4 9 13 14 18 21 6 8 7 SAVE THESE INSTRUCTIONS
5. PARTS LIST/REFERENCE (some parts may be pre-assembled) Before starting installation, check to make sure all parts are present in package.
6. GETTING STARTED Unpacking Your Filter System This product requires assembly. Carefully remove the product and all parts. Make sure all items listed in the Parts List/Reference are included. Please note that some parts may be pre-assembled. Inspect everything carefully to make sure nothing is damaged. Do not discard packing material until you have satisfactorily operated the product. If any parts are missing or damaged, please call the number listed on the front page of this manual.
7. ASSEMBLY INSTRUCTIONS (some parts may be pre-assembled) Step 1: Motor Assembly Step 1A Step 1B Strainer Lid Screws & Washers Stainer Housing Forward Strainer Basket Pump Groove Strainer Housing A. Secure the pump to the filter base with the mounting screws. The side of the pump WITHOUT the metal ID plate should face towards the groove. B. Place the strainer basket into the strainer housing. Be sure that the opening in the basket is aligned with the opening in the housing. Secure lid.
Step 3: Filling the Tank Step 3A Step 3B Sand Shield Manifold Pipe Manifold Assembly Tank B. Filling the filter tank with sand. CAUTION: AVOID BREATHING IN DUST. USE A BREATHING MASK APPROVED FOR DUST & SAND AND EYE PROTECTION WHILE FILLING THE TANK. A. Place the manifold assembly into the tank. 1. Fill the tank 1/3 full with water. 2. Place the sand shield on the center stem of the manifold. This will ensure that when filling the tank, no sand will enter the manifold assembly. 3.
Step 5: Connecting the Pump Step 5A Hose Clamp Step 5B Filter Hose Plug O-Ring Pressure Gauge Hose Adapter Step 5C Wrap thread with Teflon® Tape Hose Adapter Hose Clamp Tip Wrap thread with Teflon® Tape Waste Backwash Port Plug O-Ring O-Ring Pump Outlet Port Hose Clamp A. Connecting the pump to the valve. 1. Attach adapters to the OUTLET on the pump and the PUMP port on the valve. 8. 2. Connect the ports with the filter hose. Secure with the hose clamps.
FOR POOLS WITH 32MM OR 38MM DIAMETER UNTHREADED HOSES Hose FROM Pool Hose TO Pool O-Ring Standard Adapter Standard Adapter O-Ring POOL Outlet Hose Clamp Wrap thread with Teflon® Tape Hose Clamp Wrap thread with Teflon® Tape FOR POOLS WITH 40 MM DIAMETER THREADED HOSE CONNECTORS Hose FROM Pool Hose TO Pool O-Ring Threaded Adapter Threaded Adapter O-Ring Gasket POOL Outlet Wrap thread with Teflon® Tape Gasket Wrap thread with Teflon® Tape 13 SAVE THESE INSTRUCTIONS
9. VALVE OPERATIONS Make yourself familiar with your filter system’s valve settings and functions. Filter Valve Settings & Functions Setting Complete Water Flow/Function Filtration Regular pool filter action. This is the setting the filter will be set to most of the time. In this position, water is directed through the top of the filter where it compresses and flattens the sand. Contaminants are trapped by the sand as water makes it way to the bottom strainer, out of the filter and back to the pool.
10. FILTER OPERATIONS Start Up Once the filter system has been properly assembled, the filter tank filled with sand and the hoses connected, you may begin with filtration. However, we recommend that you clean and prepare the new sand that is in the sand chamber first. Cleaning the sand prior to filtering your pool will remove most of the dust and tiny sand particles that may exist in the sand. If you move straight to filtering, these particles will end up in your pool. Cleaning the Sand 1.
11. MAINTENANCE The chart below outlines the recommended maintenance schedule for your Pool Filter System.
12. TROUBLESHOOTING Problem Cause Solution Pressure is too low Strainer basket is dirty Clean the strainer basket. Air in Pump Poor seal on the intake side of the pump Tighten hose clamps and connection fittings. Water flows into the drainpipe Dirt around the seal of the 4 way valve Remove the 4 way valve from tank and clean the seal. Leaking filter Clamp not tight Tighten clamp. DO NOT overtighten hose clamps (35 in/lb max torque).
13. LIMITED WARRANTY STATEMENT The manufacturer warranties safe operation and reliability only under the following conditions: The filter system is installed and operated according to the assembly and operating instructions. Only original replacement parts are used. Consumable parts do NOT fall under the warranty Expendable parts do NOT fall under the warranty.
SAVE THESE INSTRUCTIONS
IMPORTANT DO NOT RETURN PRODUCT TO STORE For technical assistance and missing parts, call or email Customer Service 1.888.339.2546 (Extension 135) products@game-group.com Monday through Thursday, 8:00 am to 5:00 pm MST Friday, 8:00 am to 2:00 pm MST If replacement parts are needed please visit Amazon.com/GAMELLC Look for other GAME products at your favorite store or visit our website, www.game-group.com. /GAME.DerbyDuck Great American Merchandise & Events®, LLC 16444 N.
