PUBLISHED BY Gallagher Group Limited Kahikatea Drive, Private Bag 3026 Hamilton, New Zealand www.gallagherams.
Table of Contents Overview .................................................................................................................... 1 Electronic ID tags ................................................................................................. 2 Configurator........................................................................................................ 2 MyScale Pro .........................................................................................................
Gallagher SmartReader R Series User Manual OVERVIEW The Gallagher SmartReader R Series is a panel reader for use in permanent installations where it can be connected to: • an external power supply, and • a permanently connected data collection device. The captured Electronic ID tag data is transferred to the data collection device (Scale or computer).
User Manual Gallagher SmartReader R Series Electronic ID tags The Gallagher SmartReader enables you to read both HDX (Half Duplex) and FDX-B (Full Duplex-B) Electronic ID tags. HDX and FDX-B Electronic ID tags operate differently and therefore have different applications. Configurator The Configurator is a software program provided with the SmartReader R Series. Use it to alter settings and to diagnose performance problems in the installed SmartReader.
Gallagher SmartReader R Series User Manual USER INFORMATION SmartReader user interface Button Button Volume Function There are two volume levels on the SmartReader ON and OFF. To change the volume on the SmartReader while it is operating, press the Volume button. Note: Warning beeps (low battery warning etc) ignore the Volume setting and beep as required.
User Manual Gallagher SmartReader R Series INSTALLATION Mounting the Antenna Panel Antenna Panel Kit The Antenna Panel kit contains the following components: • Antenna Panel • Mounting instructions • Antenna Panel mounting kit: - 4 x Washers M8 x 21 mm flat Stainless steel - 4 x Bolt M8 x 70mm HEX Stainless steel - 4 x Nut M8 HEX Stainless steel - 4 x Screw Wood TEK 14 x 10 90mm - 4 x Screw Wood TEK 14 x 10 65mm Notes on locating the Antenna Panel Gallagher recommends the following when ins
Gallagher SmartReader R Series Procedure 1. User Manual Measure the vertical range of the Electronic ID tags on the animals to be scanned. 2. Determine the average height of the Electronic ID and mark this on the outside of the animal handler. 3. Determine what the Antenna Panel is to be mounted on, wood or pipe work, and prepare the appropriate mounting hardware from the supplied kit. Wood - washers and tek screws 4.
User Manual Gallagher SmartReader R Series Note: DO NOT drill through the Antenna Panel as it will damage the antenna. Note: You may want to temporarily attach the Antenna Panel and test the read range prior to permanently attaching the Antenna Panel. Mounting the SmartReader Considerations Ensure the mounting location of the SmartReader provides protection from being knocked or damaged by animals.
Gallagher SmartReader R Series User Manual Connecting the SmartReader to the Antenna Panel For information on using the 4 Metre Antenna Extension Cable Kit see 4 Metre Antenna Extension Cable Kit (p 24). 1. Ensure the SmartReader is turned off. 2. On the Antenna Panel, unscrew the Amphenol connector locking nut from the Amphenol socket and pull it down to unplug from the Antenna Panel. 3.
User Manual Gallagher SmartReader R Series Connect the SmartReader to a computer 1. Using one of the supplied cables, connect one end into the RS-232 port on the SmartReader. 2. Connect the other end into appropriate port on the Scale or computer: - Scale: RS-232 (COM Port 2) - Computer: RS-232 or USB Testing the SmartReader EID tag read range The SmartReader EID tag read range should be tested to ensure the animals passing through the animal handler are accurately and reliably identified.
Gallagher SmartReader R Series User Manual Testing the read range For your SmartReader installation you need to determine the size of the EID tag read range. If the read range is too small you need to take steps to improve it. You need to test the appropriate type of EID tag you will be using, either HDX (Half duplex) and/or FDX (Full duplex). To determine the size of your installation’s SmartReader EID tag read range, complete the following steps: 1. Turn on the SmartReader. 2.
User Manual Gallagher SmartReader R Series Investigating SmartReader read range issues If the EID tag read range on your SmartReader installation is not adequate, check the following: • The SmartReader is turned on and connected to the Antenna Panel. • The EID tag is functional and is in the correct orientation for testing. Re-test the read range by passing a small group of animals through the animal handler and reading their Electronic ID tags.
Gallagher SmartReader R Series User Manual Start the Diagnostics Wizard 1. Connect the SmartReader to a computer. See Connect the SmartReader to a computer (p 10). 2. Open the Configurator software. - Double-click on the Configurator icon on the desktop. OR a) Click on the Windows Start button. b) Select All Programs (Windows XP) or Programs (Windows 2000). c) Select MyScale. d) Click on SmartReader Configurator. 3. Click .
User Manual 12 Gallagher SmartReader R Series 4. Click on the 5. Click tab. The following window displays: .
Gallagher SmartReader R Series User Manual Assessing background noise With this window displayed, SmartReader “hears” background electrical noise like that generated by computers, mobile phones, and electrical generators for example, in the frequency band that the Electronic ID tags work in. This background noise can interfere with the reading of the Electronic ID tags. 1. Press . The following window is displayed: Note: While this window is displayed, the SmartReader will not read Electronic ID tags.
User Manual Gallagher SmartReader R Series Test read range 1. Press . The following window is displayed: 2. Follow the window instructions to test the EID tag read range in your animal handler. 3. Click . The following window is displayed: Note: While this window is displayed the SmartReader is automatically set to continuously read. The type of tag being read is shown at the bottom of the window.
Gallagher SmartReader R Series 4. User Manual Alter the mounting location of the Antenna Panel with the aim of improving the read range. See Mounting the Antenna Panel (p 4). Note: Once you have finished using the Configurator ensure you click on the disconnect button in the Configurator program prior to unplugging the cable. This ensures the data transmission returns to the correct state. Testing with live animals 1. Pass a small group of animals through the animal handler. 2.
User Manual Gallagher SmartReader R Series INSTALLING MULTIPLE SMARTREADERS When multiple SmartReaders are installed in close proximity, additional set up is required to ensure all Electronic ID tags are read correctly. Each SmartReader must be able to communicate with all other SmartReaders to enable the antenna panel to be switched on and off at the appropriate times to ensure both Electronic ID tags can be read. For additional information about tags, see Electronic ID tags (p 2).
Gallagher SmartReader R Series 4. Click User Manual . The SmartReader current settings are transferred to the Configurator and displayed. 5. Set the Synchronisation - Wireless option to On. 6. Click 7. Repeat for the second SmartReader. to copy the changes down to the SmartReader. Wired installation • Applicable if you are installing more than two SmartReaders. • Applicable for two SmartReader installations where greater reliability is required and it is practical to run the required cables.
User Manual Gallagher SmartReader R Series - Double-click on the Configurator icon on the desktop. OR a) Click on the Windows Start button. b) Select All Programs (Windows XP) or Programs (Windows 2000). c) Select MyScale. d) Click on SmartReader Configurator. 3. Click . The current settings for the connected SmartReader are displayed in the lower part of the screen. 4. Click . The SmartReader current settings are transferred to the Configurator and displayed. 18 5.
Gallagher SmartReader R Series User Manual Cabling requirements for connecting SmartReaders During the wired installation you need to connect all SmartReaders together with a cable with the following pin outs: This cable in not supplied by Gallagher - you are expected to have a custom cable made to suit the individual installation. The extra COM connectors enable you to alter the settings of each SmartReader. Create one for every SmartReader you have.
User Manual Gallagher SmartReader R Series Dual-Reader Mode This option enables increased Electronic ID reading performance, using two panel readers, which can be connected to operate in tandem as a Dual-Reader. If you are unable to get a consistent 100% read of animals in a race, then the Dual-Reader option may deliver the required performance. Positioning two panel readers opposite each other on either side of a race, enables them to be operated as if they were a single reader with a larger read range.
Gallagher SmartReader R Series User Manual The current settings for the connected SmartReader are displayed in the lower part of the window under the Operational Settings tab: 5. The Dual-Reader mode is set to the default, OFF. Select Primary to set up the master SmartReader and then select Custom Wired or Bluetooth. The Synchronisation settings default, depending on your selection. . The settings are transferred to the SmartReader. 6. Click 7. Click 8.
User Manual Gallagher SmartReader R Series 2. Plug the other end into the Female plug on the custom serial cable. 3. Plug the Male plugs of the custom serial cable into the master and slave SmartReaders. Note: If your computer does not have a serial port, use the supplied RS-232 to USB adaptor to connect to a USB port on the computer. 4. Return to Step 2. of Dual-Reader Mode to complete the installation process for Dual-Readers.
Gallagher SmartReader R Series User Manual Dual-Reader wireless installation This section describes how to connect a master and slave SmartReader using the Bluetooth module, and how to establish a connection between the SmartReaders and the data collection device. (PC, SmartTSi, Weighscale) Note: A standard serial cable will be required for this configuration, so the Primary tag data (tags read at both master and slave readers) can be transported to the data collection device. 1.
User Manual Gallagher SmartReader R Series ACCESSORIES 4 Metre Antenna Extension Cable Kit The 4 Metre Antenna Extension Cable Kit contains: • 1 x Extension cable (4m) • 1 x Mounting bracket • 2 x Metal TEK screws Mounting the extension kit to the SmartReader Mount the Antenna Panel as per Mounting the Antenna Panel (p 4). Considerations • The Extension cable is part of the Antenna Panel circuit so keep away from large metal surfaces.
Gallagher SmartReader R Series User Manual 5. On the Antenna Panel, unscrew the Amphenol connector locking nut from the Amphenol socket and pull it down to unplug from the Antenna Panel. 6. Connect the Extension cable to the Amphenol connector and tighten. 7. Mount the SmartReader on the mounting bracket by grasping the SmartReader on both sides and slide the back handle onto the mounting bracket. 8.
User Manual Gallagher SmartReader R Series OPTIONAL Overview The SmartReader (BR and R series) can be upgraded to use Bluetooth for communications between the SmartReader and a Scale, or a SmartReader and a computer. The Bluetooth upgrade needs to be done by your Gallagher distributor. For communications between a SmartReader and a Scale, a Bluetooth RS-232 adaptor will need to be purchased.
Gallagher SmartReader R Series User Manual - The "Power" LED illuminates when power is supplied to the adaptor. - The Bluetooth light flashes when a wireless connection is active. - The "Mode" LED (middle LED) only illuminates during configuration. Pairing the RS-232 Adaptor with your reader The RS-232 Adaptor must be paired with your individual SmartReader, i.e. the adaptor must be uniquely identified by your reader. This is achieved by assigning your SmartReader "MAC address" to the adaptor.
User Manual 28 Gallagher SmartReader R Series 3. Click on the Bluetooth icon. The following menu will be displayed: 4. Select the Add a Bluetooth Device option. This opens the Bluetooth Wizard. 5. Populate the My device is set up and ready to be found check box. 6. Turn on your SmartReader. A panel reader will constantly scan for a connecting computer. 7. Click Next on the Wizard.
Gallagher SmartReader R Series User Manual 8. Double click on . The following window will be displayed: 9. Select Let me choose my own passkey. Enter 0000 (four zeroes) and click Next. 10. Passkeys will be exchanged and the wizard completes. 11. Click on Finish. Note: The Bluetooth connection should be effective to a range of at least ten metres.
User Manual Gallagher SmartReader R Series SPECIFICATIONS Small Antenna Panel Small Antenna Panel 3 kg Dimensions (w x h x d) 400 x 600 x 50 mm 30
Gallagher SmartReader R Series User Manual Large Antenna Panel Large Antenna Panel 7.
User Manual Gallagher SmartReader R Series Sheep Auto Drafter Antenna Panel Sheep Auto Drafter Antenna Panel 15 kg Dimensions (w x h x d) 1080 x 900 x 200 mm 32
Gallagher SmartReader R Series User Manual SmartReader Weight R Series 1.5 kg Dimensions (w x h x d) 300 x 220 x 100 mm (approx) The front and back are slightly curved out. Power Requirements Battery 12 V Power Supply 12 V Linear Input voltage Nominal 12 V DC, Maximum 15 V DC Battery or Power supply can be plugged into the Gallagher R Series SmartReader.
User Manual Gallagher SmartReader R Series generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
Gallagher SmartReader R Series User Manual Waste Electrical and Electronic Equipment This symbol on the product or its packaging indicates that this product must not be disposed of with other waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.
ONE YEAR WARRANTY REGISTER ONLINE AT www.gallagherams.com TO EXTEND YOUR WARRANTY TO TWO YEARS FOR THIS PRODUCT FROM DATE OF PURCHASE SELLING DEALER STAMP MODEL ....................................................................................... SERIAL NO ....................................................................................... DATE PURCHASED ......................................................................................
