User's Manual

ManualsBrandsGallagher Group ManualsElectronicsProx Readers T11 Mifare and T12 Mifare

R5 | Part Number: 3E2512 | 1

Installation Note | Gallagher T12 Reader

Installation Note

Gallagher T12 Reader

The Gallagher T12 Reader

The Gallagher T12 Reader is a smart card proximity reader. It can be installed

as either an entry reader or exit reader. It can be mounted on a BS 4662 British

Standard square flush box.

The reader can read Mifare DESFire EV1, Mifare Plus and Mifare Classic cards.

The Multi Tech variant can also read 125Khz cards.

Gallagher T12 Multi Tech Readers only: Using dual technology 125/Mifare

cards with Gallagher T12 Multi Tech Readers may cause both card technologies

to be read, resulting in double card badges and unusual reader feedback.

Gallagher strongly recommends against using dual technology 125/Mifare

cards with Gallagher Multi Tech Readers for sites running pre-Command Centre

v7.00 software (due for release 2nd half, 2011). From Command Centre

v7.00, a site may specify which technology a Multi Tech reader should read

off a dual technology card.

This equipment contains components that can be damaged by electrostatic

discharge. Ensure both you and the equipment are earthed before beginning

any servicing.

Summary of content (11 pages)

PAGE 1
Installation Note | Gallagher T12 Reader Installation Note Gallagher T12 Reader This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. Gallagher T12 Multi Tech Readers only: Using dual technology 125/Mifare cards with Gallagher T12 Multi Tech Readers may cause both card technologies to be read, resulting in double card badges and unusual reader feedback.
PAGE 2
Installation Note | Gallagher T12 Reader The reader sends information to the Cardax FT Controller and acts upon information sent from the Cardax FT Controller. The reader itself does not make any access decisions. The Gallagher T12 Reader uses the “Cardax IV Reader” communications protocol to communicate with the Cardax FT Controller.
PAGE 3
Installation Note | Gallagher T12 Reader Manufacturer reference Cable format* Combined power and data in a single cable Data only in a single cable CAT5E 4 twisted pair Each 2 x 0.2mm2 (24 AWG) 100m (330ft) 300m (1000ft) SEC472 4 x 0.2mm2 Not twisted pairs (24 AWG) 100m (330ft) 250m (800ft) SEC4142 4 x 0.4mm2 Not twisted pairs (21 AWG) 150m (500ft) 150m (500ft) BELDEN 8723 2 twisted pair Each 2 x 0.4mm2 (22 AWG) 100m (330ft) 150m (500ft) BELDEN 9842 2 twisted pair Each 2 x 0.
PAGE 4
Installation Note | Gallagher T12 Reader Installation The Gallagher T12 Reader is designed to be mounted on a standard British electrical flush box, or any solid flat surface. However installation on metal surfaces, particularly those with a large surface area will reduce read range. The extent to which the range is reduced will depend upon the type of metal used. The recommended mounting height for the reader is 1.1m (3.6ft) from the floor level to the centre of the reader device.
PAGE 5
Cardax IV Reader Installation Note | Gallagher T12 Reader Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX Red Black Orange Green Brown White Blue 5. Fit the facia assembly into the base by clipping the small lip, into the top of the base and holding the top, press the bottom of the facia assembly down into the base. 6. Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole at the bottom of the base to secure the facia assembly.
PAGE 6
Installation Note | Gallagher T12 Reader Connecting to the Cardax FT Reader Module (for the Controller 6000) C 4 5 6 C 1 2 3 Red Black Orange Green Brown White Blue R2 Out R2 In Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX R1 Out R1 In Red Black Orange Green Brown White Blue + Cardax IV Reader 2 Positive Negative Reserved Reserved Reserved CDXIV TX CDXIV RX Cardax IV Reader 1 Connect the wires to the sockets as shown: Cardax FT Reader Module Connecting to the Cardax FT GBUS
PAGE 7
Installation Note | Gallagher T12 Reader Connecting to the Cardax FT Controller 3000-4R or 3000-8R The ports to which the Gallagher T12 Reader can connect are set up as groups, as follows: • Two groups (numbered 1 and 2) on the Controller 3000-4R, and • Four groups (numbered 1 to 4) on the Controller 3000-8R Each group provides connection for two Gallagher T12 Readers. Refer to the following diagram for the location of the ports on the Cardax FT Controller 3000-8R.
PAGE 8
Installation Note | Gallagher T12 Reader Make the connections from the Gallagher T12 Reader to either the Cardax FT Controller 3000-4R or 3000-8R as shown: Cardax FT Controller 3000-4R or 3000-8R Group PB1 and PA1... to...
PAGE 9
Installation Note | Gallagher T12 Reader Technical Specifications Technical Specifications Routine maintenance: Not applicable for this reader Cleaning: This reader should only be cleaned with a clean, lint free, damp cloth Power required: Voltage: 9Vdc - 16Vdc Current (at 12Vdc): 89mA (standby) Standard variant 124mA (peak) Standard variant 88mA (standby) Multi Tech variant 140mA (peak) Multi Tech variant Temperature Range: -30°C to +70°C Note: Direct sunlight may increase the internal reader temperature
PAGE 10
Installation Note | Gallagher T12 Reader FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressly approved by Gallagher Group Limited could void the user’s authority to operate this equipment.
PAGE 11
Drill Template 15mm (0.59 inches) 86mm (3.39 inches) 13mm (1/2 inch) diameter hole for cable 22.3mm (0.88 inches) 26mm (1 inch) 29mm (1.41 inches) 25mm (1 inch) 40mm (1.57 inches) 35mm (1.38 inches) 25mm (1 inch) 86mm (3.