User Manual

ManualsBrandsGallagher Group ManualsElectronicsCardax IDT (125 Series)

Installation Note

Cardax FT Intelligent

Door Terminal (125 Series)

Part number 3E0054 R2 1

March 2003

CAUTION

This equipment contains components that can be damaged by

electrostatic discharge. Ensure both you and the equipment are

earthed before beginning any servicing.

3E0054 R1

December 2002

The Cardax FT Intelligent Door Terminal (125 Series)

The Cardax FT Intelligent Door Terminal (125 Series) is a "remote" proximity

reader with text display and an inbuilt Intercom, designed to connect only to

Cardax FT Controller 5000s.

It can be installed as either an entry and/or exit reader and the Intercom enables

communication with the console operator.

The IDT has a back-lit keypad and an inbuilt Liquid Crystal Display (LCD).

The LCD can display both text and graphics to aid the cardholder.

The IDT sends information to the Cardax FT Controller and acts upon

information sent from the Cardax FT Controller. The IDT itself does not make

any decisions.

The "Cardax FT Prox Reader and IDT Cover" can be fitted over the IDT to

prevent the IDT being damaged by vandal attack and to increase protection

against harsh weather. Refer to the "Prox Reader and IDT Covers" Installation

Note (part number 3C4589).

Summary of content (8 pages)

PAGE 1
Installation Note Cardax FT Intelligent Door Terminal (125 Series) CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you and the equipment are earthed before beginning any servicing. 3E0054 R1 December 2002 The Cardax FT Intelligent Door Terminal (125 Series) The Cardax FT Intelligent Door Terminal (125 Series) is a "remote" proximity reader with text display and an inbuilt Intercom, designed to connect only to Cardax FT Controller 5000s.
PAGE 2
Before you begin Shipment contents Unpack the Cardax FT IDT (125 Series) and check the shipment contains the following items: • 1 x Cardax FT IDT (125 Series) base • 1 x Cardax FT IDT (125 Series) facia (pre-assembled with Processor, Display and Keypad PCBs) • 1 x Interconnect PCB • 1 x Cardax FT Intelligent Door Terminal (125 Series) Installation Note (part number 3E0054) • 1 x cable assembly • 4 x self tapper pan-head fixing screws • 4 x screw caps Note: Once the reader is installed, you req
PAGE 3
RS485 Communications High quality twisted pair communications cable with low capacitance typically Category 5 (CAT5) cable is used for communications cabling. DC Power The maximum recommended length of the DC power cable is dependant on the diameter of the conductor and the current drawn by the IDT. Mounting Note: The Cardax FT IDT (125 Series) has been designed to metric specifications therefore any imperial measurements provided are approximate only.
PAGE 4
Installation Instructions 1. Considering the recommended mounting height, mark the position where the IDT is to be mounted. Note: It is very important the base of the IDT is flush with, and tight against, the mounting surface. If you are mounting the IDT on a rough surface, make the surface as smooth as possible under the IDT and up to 25mm (1 inch) around the IDT. Failure to do so may mean it could be difficult to remove the reader at a later date. 2.
PAGE 5
13. Refit the facia onto the base. Clip the front over the top edge of the base and press the bottom of the facia down. Note: The pins on the Interconnect PCB in the base of the Cardax FT IDT (125 Series), fit into the slots on the main PCB. The connector should be fitted to the base, not the facia assembly.
PAGE 6
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 7
Viewing angle adjustment The LCD is temperature compensated which enables it to maintain optimum contrast. The viewing angle is factory set and you should not need to alter the setting of the Viewing angle potentiometer. Removal and replacement Note: Ensure you follow full antistatic precautions. Removing the Facia To remove the facia from the Cardax FT IDT (125 Series) base you need the plastic de-latching tool (part of part number C41608) shown below. The end of the tool is used for removing the facia.
PAGE 8
Technical specifications Routine maintenance and serviceable parts Not applicable for a Cardax FT IDT (125 Series) Cleaning The Cardax FT IDT (125 Series) should be only be cleaned with clean, lint free, damp cloth Power required: Voltage 13.