Installation Instructions
Table Of Contents
- BS 470/471 611 BS 474/475 611 BS 484/485 611
- Table of ContentsInstallation instructions
- IMPORTANT SAFETY INSTRUCTIONS
- Before you beginBefore you begin
- Preparing Kitchen UnitsPreparing Kitchen Units
- Dimensions and Cabinet Requirements
- Removing Packaging
- Water connection
- Waste water connection
- Install Appliance
- Note:
- Mount to Cabinet
- Adjusting the door
- Three wire connection
- Combination with an oven
- Combination with warming drawer, width 24" (60 cm)
- Combination with warming drawer, width 30" (76 cm)
- Check the Installation
- Removal
- Customer serviceCustomer service
- Avant de commencerAvant de commencer
- Préparation des meublesPréparation des meubles
- Exigences en matière de dimensions et d'armoire
- Pour enlever l’emballage
- Raccordement de l’eau
- Raccord d'évacuation
- Installation de l’appareil
- Remarque :
- Fixation à l'armoire
- Ajustement de la porte
- Connexion à trois fils
- Association avec un four
- Combinaison avec un tiroir chauffant de largeur 24 po (60 cm)
- Combinaison avec un tiroir chauffant de largeur 30" (76 cm)
- Vérification de l'installation
- Dépose
- Service après-venteService après-vente
- Antes de empezarAntes de empezar
- Preparar los muebles empotrablesPreparar los muebles empotrables
- Dimensiones y requisitos del gabinete
- Quitar el embalaje
- Toma de agua
- Conexión de aguas residuales
- Montaje del electrodoméstico
- Nota:
- Monte el electrodoméstico en el gabinete
- Ajustar la puerta
- Conexión a tres cables
- 1 Conecte el cable rojo del horno al cable rojo del suministro eléctrico (cable con corriente).
- 2 Conecte el cable negro del horno al cable negro del suministro eléctrico (cable con corriente).
- 3 Conecte el cable de conexión a tierra amarillo/ verde del horno al cable de conexión a tierra desnudo del suministro eléctrico.
- Combinación con horno
- Combinación con cajón calentador (anchura 24")
- Combinación con cajón calentador (anchura 30")
- Pruebe la instalación
- Desmontaje
- Servicio de Atención al ClienteServicio de Atención al Cliente
11
For this purpose, slightly pull out the appliance from the
built-in cut-out. At the top of the appliance there is an
oval opening located on the hinge side. Remove the
cover cap. Slightly loosen both screws (Inbus 5 mm),
but do not remove them!
Align the door via the lateral screw (Torx 20).
Tighten both screws (Inbus 5 mm) again. Attach the
cover cap again.
Notes
‒ The alignment of the appliance door can be
adjusted via the upper hinge, in order to achieve a
precise gap size of the top edge of the door to the
upper air output.
‒ The height of the door cannot be adjusted.
‒ The device door is already aligned when the
appliance is delivered. You do not normally need to
align the door.
Three wire connection
BO 450/451-610
1 Connect red wire from oven to red electrical supply
wire (hot wire).
2 Connect black wire from oven to black electrical
supply wire (hot wire).
3 Connect yellow/green ground oven wire to bare
ground electrical supply wire.
Attach flexible conduit to the junction box.
To facilitate serviceability, the flex conduit must not be
shortened and should be routed to allow for temporary
removal of the oven.
Combination with an oven
In the case of the BS 474/475 and BS 484/485
appliance versions, the control panel is at the bottom.
As a result, these models are particularly suitable for
installation over a Gaggenau Series BO 4.. oven.
Fit the Combi-steam oven first and then the oven.
For an installation depth of 21
5
/
8
" (550 mm), position
the water hoses and the connecting cable in the area of
the housing cut-out.
The rear of the BO 4.. ovens has a bevelled corner.
Route the Combi-steam oven's connecting cable and
supply and drain water hoses downwards to the
connection points on the rear left in the kitchen unit.
7RU[