TM-SX / TILTING WALL MOUNT for Extra-Large Flat-Panel Displays TM-SX / TILTING WALL MOUNT / X-LARGE User Manual
Thank you for choosing Gabor. The Gabor TM-SX Tilting Wall Mount offers durable and discreet support for extra-large flat panel displays measuring 70 to 90 inches and weighing up to 176.4 pounds. This mount’s slim 2.37-inch profile assures that your screen will hang practically flush against the wall. And an anti-theft locking bar adds security, making the mount ideal for public spaces. If you have safety concerns about installing this product, contact a qualified professional or installation contractor.
Safety Warnings • When installing this product, be sure to refer to the mounting instructions detailed in this manual; failure to abide by the mounting instructions may void the product’s warranty. • Do not mount the device on structures that may be affected by vibrations or noticeable impacts; do not install near a heater, fireplace, or any other source of direct heat energy.
Product Specifications 4 Depth from Mounting Source 2.37 in. (6 cm) Max Weight Capacity 176.4 lb. (80 kg) Recommended Screen Sizes 70 to 90 in. (177.8 to 228.6 cm) Material Steel VESA Mounting Patterns 200×200 mm 300×300 mm 400×200 mm 400×400 mm 600×400 mm 800×400 mm Weight 8 lb. (3.
Overview Required Tools Display Brackets Wall Bracket Drill Phillips screwdriver TM-SX / TILTING WALL MOUNT / X-LARGE Adjustable crescent wrench A 4X B 4X C 4X D 4X E 4X F 4X G 8X Hammer M6,M8 Stud finder M5 M5 × 14 mm screws H 8X Large spacers M6 × 14 mm screws I 6X M6 × 55 mm anchor screws M6 × 30 mm screws J 6X 10 × 45 mm concrete anchors M8 × 30 mm screws M8 × 50 mm screws Rectangle washers K L M 6X M6 anchor screw washers 1X 1X Small spacers N 1X Tape m
Display/TV Placement Before installing the Gabor Tilting Wall Mount, you will need to determine the placement of your display and identify surrounding support structures for attachment. The best height for a display is at the viewer’s eye level. You can find this height in one of two ways. 1. Measure the distance from the seating area to the viewing area. The ideal position is when the center of the display (where the diagonals meet) is as close as possible to eye level. OR 2.
Attaching the Display/TV Brackets Selecting the Right VESA Mounting Hardware for Your Display A variety of screws are included to fit VESA standards on the backs of most displays. Select the M4, M5, M6, or M8 screws and washers that best fit your display. Hand-thread the screws to determine the correct diameter. A 4X B 4X C 4X D 4X E 4X F 4X G H 8X 8X If the screw is too short, it may not hold the display. If it’s too long, it may damage the display.
Attaching the Wall Bracket to Wooden Studs K 6X N 1X WA TM LL -SX MO UN / TIL T TIN / X-L G AR GE I 6X Wooden studs run vertically inside the wall, 16 inches apart, behind the drywall or plaster. The wall bracket must be mounted to a wooden stud, or the bracket could fall out and damage your display or cause personal harm. Use a stud finder to locate the edges of the wooden studs, and mark the center of each stud. 2.
Attaching the Wall Bracket (cont.) Wooden Studs Wall bracket mounted to wooden stud, with correct screw placement.
Attaching the Wall Bracket to Concrete J 6X K 6X 1. Place the wall bracket up to the location marked for your display, and use a pencil to mark the six drilling holes needed for the concrete anchors. Use the included bubble level to make sure the bracket is level before drilling. 2. Use a 3/8-inch (10 mm) concrete drill bit to predrill the marked spots 2.4 inches (60 mm) deep, and then clean out the debris from the holes. 3.
Attaching the Wall Bracket (cont.) Concrete Wall bracket mounted to concrete, with correct screw placement.
Mounting the Display on the Wall Bracket Warning! We recommend that two people perform this step. 12 1. Lift your display up to the wall bracket, and hang the display from the top hooks of the brackets. 2. Slide the locking bar, from the display’s right side, in between the bottom hooks of the brackets and behind the wall bracket’s bottom flange. The locking bar’s eyelet should extend slightly from the left side of the wall bracket.
Post-Installation Adjustment M Once your display is mounted on the wall mount you can fine-tune the horizontal level, and adjust the tilt angle +5° to -10°. Horizontal Level If necessary, use the included hex key to turn the adjustment screws located at the top of each display bracket. Tilt Angle Use the tilt tension knobs on both brackets to adjust the tension for the tilting mechanisms. Tilt the display into the ideal viewing angle from +5° to -10°, and tighten the tilt tension knobs until secure.
Padlock Security For extra protection against display theft, install a padlock (not included). This provides added security and is ideal when using the mount in public spaces. Insert a lock through the locking bar’s eyelet.
One-Year Limited Warranty This Gabor product is warranted to the original purchaser to be free from defects in materials and workmanship under normal consumer use for a period of one (1) year from the original purchase date or thirty (30) days after replacement, whichever occurs later.
WWW.MADEBYGABOR.
