MD-AD13MB / DUAL SEGMENT MONITOR mount For 13″–27″ (33-69 cm) LCD desktop computer monitors User Manual
Thank you for choosing Gabor. The Gabor MD-AD13MB mounts your 13″–27″ (33-69 cm) LCD computer monitor. It attaches to your desk via a built-in clamp, freeing up valuable desk space and enabling personalized monitor placement for improved safety and comfort over conventional monitor stands. This desktop mount incorporates a dual-segment arm with multiple points of articulation to provide a full range of motion, making it easy to adjust your monitor’s horizontal position, tilt, swivel, and roll.
User Manual Welcome 3
(x1) Overview F Mounting Arm G Shaft cap Mounting socket Locking collar Ratchet handle VESA mount Hex screws ±15° Shaft Cable clips Clamp Clamp locking knob Overview 4 Locking knob Tools Required for Installation • Phillips Screwdriver
A Also Included B A B M4x12 (x8) M5x12 (x8) Supplied Parts & Hardware A A (4) M4 × 12 screws B (4) M4 × 30 screws C (4) M5 × 12 screws M4x12 (x8) M4 A A A x4 A C D (4) M5 × 30 screws E 4(x8) mm hex key M5x12 (x8) M4x12 F Shaft cap M5x30 (x8) M4x30 (x8) B A A C C B B B B C x4 M5 M5x12 (x8) S=4mm (x1) M5x30 (x8) M4x30 (x8) B 13X5.5X16.5 (x8) G (4) Spacers H Locking collar (x8) 13X5.5X16.5 I User Manual C C Hex Key & Cap D E x1 (x8) 13X5.5X16.
Product Specifications 360° Monitor display size: 13″–27″ (33–69 cm) 360° Maximum load capacity: 22 lb. (10 kg) VESA standards: 75 × 75, 100 × 100 Tilt: ±15° Swivel: 360° 180° Roll: 360° Installation: Horizontal surfaces up to 2.4″ (6 cm) thick Maximum arm extension: 16.3″ (41.3 cm) Spacer dimensions Length: 16.5 mm Outer diameter: 13 mm Inner diameter: 5.5 mm Height: 22.8″ (58 cm) Weight: 5.1 lb. (2.
Safety Warnings 1 Please read and follow these instructions and keep this manual in a safe place. 2 Clean this product with only a soft, dry cloth. 3 Keep this product away from children. 4 Make sure everything is secure before proceeding. 5 Make sure that this product is intact and that there are no missing parts. 6 To avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings. 7 Do not exceed the maximum load capacity.
Getting Started Decide where you want to place your monitor. Position your monitor directly in front of you, at eye level, and approximately at an arm’s length away. You shouldn’t need to turn your head to look at your monitor. If you have to strain to look at it, readjust its position.
Attaching the Shaft The MD-AD13MB easily attaches to most desks up to 2.4″ (6 cm) thick, even if your desk is nearly flush against a wall. Before attaching the shaft to your desk, make sure you have enough room to fit the entire clamp behind your desk. 1. Loosen the clamp locking knob until you can fit the clamp over the edge of your desk. 2. Fit the clamp over the edge of your desk, and tighten the clamp locking knob until the shaft is securely mounted to your desk.
Attaching Your Monitor to the VESA Mounts: Before attaching your monitor to the VESA mount, you may need to detach your monitor’s built-in stand. For information on how to do this, consult your monitor’s user manual. Depending on how the rear of your monitor is configured, you can use one of two methods to install the VESA mount onto your monitor: recessed or flush. If your monitor’s VESA mounting holes are in a recessed area of the monitor, use the Recessed Installation instructions on page 12 .
Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. Installation Instructions 11 C A~B TV 3. Depending on your monitor’s thread size, insert four of the included M4×12 or M5×12 screws into the VESA mount and use a Phillips-head screwdriver to fasten them until fully tightened. TV 1. Carefully place your monitor facedown on a flat surface. Continue to Attaching the Mounting Arm Assembly on page 13. TV 2.
Recessed Installation Note: Before starting, make sure the VESA mount, mounting arm, and monitor are facing the proper direction. 1. Carefully place your monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 12 Installation Instructions 2. Place four of the included spacers on each of your monitor’s four VESA mounting holes. Tip: Thread each of the screws by hand before fastening them with the screwdriver. 3.
Attaching the Mounting Arm Assembly 1. Loosen the locking collar by rotating the ratchet handle, and then slide the collar onto the shaft. 2. Slide the locking collar to the height at which you want to mount your monitors, and then tighten the ratchet handle to lock the collar in place. 3. Slide the mounting arm assembly (with monitor attached) onto the shaft so it rests on the locking collar, and then fully tighten the locking knob until secure. 4. Insert the protective cap into the top of the shaft. 5.
or -2 Adjusting Tension and Articulation 13" - 27"(33-69cm) Arm Positioning Monitor Tilt, Swivel, and Roll The mounting arm has two joints, making it easy to adjust your monitor’s horizontal placement. Position the arm as desired and use the included 4 mm hex key to fasten the hex screws until fully tightened. You can adjust the (vertical) tilt and (horizontal) swivel action of your monitor for optimal viewing comfort.
Customer Support For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2014 Gradus Group LLC. All Rights Reserved.
www.madebygabor.
