LeviTouch DM-502 DUAL-ARM MONITOR MOUNT For 15 – 27 in. (38.1 – 68.
Thank you for choosing Gabor. The Gabor Dual-Arm Desktop Mount can securely support two monitors from 15 to 27 inches. The rugged aluminum build and gas spring mechanism will hold two monitors each weighing up to 17.6 pounds. Both mounts consist of two articulating halves that give you maximum control over swivel, tilt, rotation, and height for precise monitor placement. This desktop mount includes a heavy-duty, low-profile double clamp that will fit into a space with tight clearance, like a cubicle.
Welcome 3
OVERVIEW Quick release Tilt / swivel adjustment screws VESA mount Tension adjustment screw Cable guides Audio in and out jacks USB 3.
ALSO INCLUDED Supplied Parts & Hardware A M4 × 12 screws B M4 × 30 screws C M6 × 12 hex screws D 4 mm hex key E M8 × 12 hex screws F 5 mm hex key G Spacers H Desk plates M4 M6 M8 Parts A ×8 C ×8 E ×4 G ×8 B ×8 D ×1 F ×1 H ×2 Overview 5
PRODUCT SPECIFICATIONS 44.7 in. (113.5 cm) Monitor display size: 15–27 in. (38.1–68.6 cm) ±90° Maximum load capacity: 17.6 lb. (8 kg) 100 75 Maximum desktop thickness: 3.5 in. (9 cm) ±180° Swivel: 180° +90°/-85° Rotation: 360° Arm pivot: 180° +90°/-85° Base rotation: 135° Maximum arm height: 17.7 in. (45 cm) Arm height adjustment: 14 in. (35.6 cm) Connectors: USB 3.0: Standard-A (×2) Audio: 1/8 in. (3.5 mm) stereo male (×2) Ports: USB 3.0: Standard-A Audio: 1/8 in. (3.
SAFETY WARNINGS 1 Please read and follow the instructions, and keep this manual in a safe place. 2 Clean this product with only a soft, dry cloth. 3 Keep this product away from children. 4 Make sure everything is secure before proceeding. 5 Make sure that this product is intact and that there are no missing parts. 6 To avoid damage to this product, be careful not to overtighten or improperly thread any of the threaded fittings. 7 Do not exceed the maximum load capacity.
ASSEMBLY INSTRUCTIONS 1. Attach both desk clamp mounts to the base with the M6 × 12 hex screws. Use the 4 mm hex key to tighten the screws until secure. 8 Assembly Instructions 2. Align the desk plates with the provided holes, and press them into place over the screws of both clamps. 3. Attach the clamps to the clamp mounts with the M8 × 12 hex screws. Use the 5 mm hex key to tighten the screws until secure.
Important! If you’re installing the desktop mount in a cubicle or other space with limited clearance, slide the clamp mounts between your desk and the partition first. Then attach the clamps to the clamp mounts from underneath the desk. 4. Tighten each clamp with the locking knob. For the most stability, the clamps should be parallel to the back edge of your desk. Make sure the desktop mount doesn’t wobble or shift and is securely clamped to the desk before proceeding.
ATTACHING THE MONITORS Flush Installation 1. Carefully place each monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 10 Attaching the Monitors 2. Align the holes in the VESA mount with the corresponding mounting holes in your monitor. Important: Make sure the raised edge of the VESA mount is at the top of your monitor. 3.
Recessed Installation If the back of your monitors have a recessed area for the VESA mount, follow these steps: 1. Carefully place your monitor facedown on a flat surface. Tip: To avoid scratching the screen, place your monitor on a soft cloth such as a towel. 2. Align the spacers with the mounting holes in your monitor. 3. Align the the VESA mount holes with the spacers' mounting holes and monitor mounting holes. 4.
MOUNTING THE MONITORS Once attached to the monitor, slide the VESA mount into the quick release until it locks into place. To remove the monitor, pull the locking tab while lifting the monitor out of the quick release.
ADJUSTING TENSION AND ARTICULATION Important! The arm tension is preset for lighter monitors. To avoid damage, do not continue to loosen the screw if it’s already loose. Arm Tension To support your monitor’s weight, you can adjust the tension of each mounting arm individually with the included 5 mm hex key. The tension adjustment screw is located in the joint between the two arm segments. • For heavier monitors, rotate the screw counterclockwise to increase tension.
Tilt Monitor Swivel and Tilt Two adjustment screws at the top of each mounting arm regulate the monitor’s (vertical) tilt and (horizontal) swivel action. Position your monitor as desired, and use the 5 mm hex key to tighten the screws (clockwise) to fix the monitor in its position. If you want the monitor to swivel and tilt more freely, use the 5 mm hex key to loosen the screws (counterclockwise). Important! Always hold your monitor with one hand when changing the tension of either screw.
ATTACHING THE CABLES TO YOUR COMPUTER The Dual-Arm Desktop Mount offers USB and audio connectivity with your computer, and it gives you two convenient USB 3.0 and audio ports on your desktop. 1. Connect the USB plugs to available USB ports on your computer or a USB hub. 3. Connect the green mini plug to the audio output (headphone) jack on your computer. 2. Connect the pink mini plug to the audio input (mic) jack on your computer.
CABLE ORGANIZATION The desktop mount comes with cable guides on each arm to organize the cables from your monitors and prevent clutter 1. Remove the top cable guide by pressing in on the tabs and pulling the guide out of the arm. 16 Cable Organization 2. Place the monitor cable inside the guide, and snap it back into place. 3. Remove the bottom cable guide by unscrewing the Phillips screw, and gently pull and slide it out of the guide slots. 4. Run the cable inside the guide.
TROUBLESHOOTING The desk is too thick for the clamp. If your desktop is thicker than 3.5 in. (9 cm), follow these steps: 1. Remove the clamps from the clamp mounts. 2. Completely remove the clamp screws and attachments. 3. Turn the clamps upside down, and reattach the clamp screws and attachments. The monitor won’t stay in one position. • Make sure your monitor weighs less than 17.6 lb. (8 kg). • Adjust the arm tension by turning the adjustment screw counterclockwise to increase the tension.
CUSTOMER SUPPORT For more information or to arrange service, visit www.madebygabor.com or call Customer Service at 212-594-2353. Product warranty is provided by the Gradus Group. www.gradusgroup.com Gabor is a registered trademark of the Gradus Group. © 2016 Gradus Group LLC. All Rights Reserved.
Customer Support / Warranty 19
WWW.MADEBYGABOR.
