Parts List

ManualsBrandsG&G ARMAMENT ManualsAirsoftG980

Manufactured by G&G ARMAMENT

100% Made in Taiwan

[ Address ]

Changhua Headquarters / No. 999, Zhonghua Rd., Shengang Township, Changhua County 50952, Taiwan

Taipei Office / 11F-3,NO.27,Lane 169,Kangning St,Shijr City, Taipei County 22180,Taiwan

Warehouse in USA / 1122 Coiner Court City of Industry, CA91748 U.S.A.

[ E-Mail ]

Sales Department / sales@guay2.com

b2b@guay2.com

Technology support Department / support@guay2.com

Warehouse in USA / sales101@guay2.com

[ Tel ]

Changhua Headquarters / 886-4-798-9000 (Technical Support Line)

Taipei Office / 886-2-2692-2000

Warehouse in USA / (1) 626.581.0101

[ Fax ]

Changhua Headquarters / 886-4-798-9900

Taipei Office / 886-2-2692-4000

Warehouse in USA / (1) 626.581.1011

Summary of content (8 pages)

PAGE 1
[ Address ] Changhua Headquarters / No. 999, Zhonghua Rd., Shengang Township, Changhua County 50952, Taiwan Taipei Office / 11F-3,NO.27,Lane 169,Kangning St,Shijr City, Taipei County 22180,Taiwan Warehouse in USA / 1122 Coiner Court City of Industry, CA91748 U.S.A. [ E-Mail ] Sales Department / sales@guay2.com | b2b@guay2.com Technology support Department / support@guay2.com Warehouse in USA / sales101@guay2.
PAGE 2
Introduction 1 Contents 01 Introduction 02 Components 03 Warning 05 Selector and safety setting 06 Installing CO2 cartridge 07 Sight adjustment 08 Removing the bolt & Hop-up adjustment 09 Loading the magazine 10 Installing the rifle sling 11 Parts list 13 Maintenance 14 Trouble shooting 2 Magazine catch Bolt handle Introduction Bolt Components Rear sight Barrel Stock plate G980 was derived from an earlier rifle (The Karabiner 98 Kurz).
PAGE 3
4 Warning 3 Orange tip disclaimer： All G&G Airsoft products come with a permanently affixed blaze orange tip required by United States law to comply with any and all safety regulations. If you alter, remove, or modify the orange tip, the warranty will be Void. For more product information please visit our website www.guay2.com All products employ high precision 6.04mm barrel. Use with precision 5.95mm BB pellets is highly recommended. Damage to the product due by faulty BB pellets voids the warranty.
PAGE 4
Warning 5 Selector and safety setting ► Don’t expose CO2 cartridges to heat or store them at temperatures above 120°F(48.9°C). ► Don’t mutilate or incinerate CO2 cartridges. ► Keep hands and face away from escaping CO2 gas. It may cause frostbite if it comes in contact with skin. Warning ► Never operate the selector while pulling the trigger. Otherwise, malfunctions may occur. ► Pulling the trigger with the selector being set at safe mode may damage the airsoft gun.
PAGE 5
Sight adjustment 8 7 Removing the bolt & Hop-up adjustment Front sight adjustment Hop-up adjustment Left Right 2 1 Left Push the left side receiver button. Right Remove the front sight hood. Turning the screw will move the pellet hitting point to the left or right. Removing the bolt Hop 1.Move the bolt stop away. 2.Remove the bolt handle. Warning Rear sight adjustment Press the button and slide forward or ► Never hold the gun sideways as the BB pellets will curve right or left.
PAGE 6
Loading the magazine 10 9 Installing the rifle sling 2 1 1.Press magazine catch button. 2.Remove the magazine. 1.Loop back around and slide under the sling's loop. 2.Slide the sling through the adjustable clamp. Load G&G 5.95 mm BB pellets into the magazine. Warning ► Make sure to set the magazine upwards.It is securely installed when you hear a click sound. ► Confirm that the safety lever is set to safety position and do not place your finger on the trigger.
PAGE 7
Parts list 11 G9 1 2 3 1 ► You may buy all of the groups’ parts from G&G support Dep or your Local G&G distributor.
PAGE 8
Maintenance 13 14 Warning ► Make sure no dirt gets into the chamber to avoid clogging of pellets. ► Hop-up may be unstable for the first 200 to 300 rounds after using silicone oil, this is the normal operation of the gun. ► Never use CRC-556, WD40 or other corrosive lubricant. Trouble shooting 1 Check to ensure that your lubricant reservoir is at the required level for optimal operation. This can cause mechanical malfunctions if not properly maintained.